LM2903BIDSGR - Dual 38V Comparator | Texas Instruments
MPN: LM2903BIDSGR ✓ AktifLM2903BIDSGR Genel Bakış
An analog comparator is a semiconductor that compares two input voltages and produces a logic-level output indicating which input is higher. Comparators belong to the broader analog IC hierarchy alongside amplifiers, voltage references, and data converters. They are used to implement threshold detection, sensing, overvoltage protection, oscillator functions, and digital-interface conditioning when open-collector outputs are advantageous.
The LM2903B family provides a maximum input rating of 38 V, an input offset voltage as low as 0.37 mV, and an input bias current as low as 3.5 nA. Its open-collector output stages can sink output current and support pull-up connections to the system supply, allowing the device to interface with TTL, MOS, and CMOS logic. Dedicated input ESD clamps provide an HBM ESD rating of 2 kV.
The B-version improves the original LM2903 family through lower offset voltage, lower input bias current, lower supply current, faster response, wider supply capability, and improved input ruggedness. Its common-mode input voltage range includes ground, which supports sensing around a zero-volt reference when the supply conditions permit operation near that boundary. The 1 us response time also makes the device suitable for faster control loops than classic general-purpose comparators.
Typical uses include DC overvoltage and undervoltage detection, sensor threshold interfaces, battery and power-supply monitoring, window comparators, relaxation oscillators, and industrial control logic interfaces. The compact 2 x 2 mm WSON package helps reduce board area where dense analog and mixed-signal layouts are required.
Designers should preserve adequate input and output separation when operating near absolute maximum limits, place pull-up resistors close to each open-collector output, and route sensitive input traces away from switching nodes. The exposed thermal pad should be connected to the ground plane according to the package land pattern and thermal design guidance.
This page combines the LM2903BIDSGR electrical characteristics, package and lifecycle information, replacement assessment, comparison data, and practical PCB guidance to help engineers evaluate the device quickly and design a robust comparator circuit.
Drop-in alternatifler için LM2903BIDSGR — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu ürüne yer değiştirme seçenekleri mevcut değil.
Alternatifleri Talep EdinLM2903BIDSGR Maksimum Değerlendirmeler & Elektriksel Özellikler
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Maximum Voltage Rating | 38 V |
| Differential Input Voltage Range | -38 V to +38 V |
| Common-Mode Input Voltage Range | Includes ground |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Besleme Akımı | 200 uA per comparator |
| Response Time | 1 us |
| ESD Rating | 2 kV HBM |
| Çıkış Türü | Open collector |
| Input Common-Mode Behavior | Rail-to-rail |
| Logic Compatibility | Compatible with TTL, MOS, and CMOS |
| Paket | 8-WSON, 2 x 2 mm |
| Pin Sayısı | 8 pins |
| Montaj Türü | Surface mount |
| Industrial Grade | Yes |
LM2903BIDSGR 8-wson, 2 x 2 mm Pin Yapısı Kılavuzu
LM2903BIDSGR (8-wson, 2 x 2 mm paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: LM2903BIDSGR.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LM2903BIDSGR için uygundur 6 uygulamas: Industrial Overvoltage Protection, Battery Voltage Monitoring, Sensor Threshold Interface, Window Voltage Comparator, Relaxation Oscillator, Digital Control Signal Conditioning.
Industrial Overvoltage Protection
The LM2903BIDSGR fits overvoltage supervision because each comparator can evaluate a divided feedback voltage against a reference and pull an open-collector output low when the monitored rail exceeds its threshold. Its 38 V maximum rating provides headroom for industrial supply transients, while the 0.37 mV input offset helps reduce threshold error. The 1 us response time permits rapid shutdown signaling. Add a pull-up resistor to the system logic supply and account for propagation delay in the protection sequence.
Önerilen
Battery Voltage Monitoring
LM2903BIDSGR is suitable for battery-pack monitoring where two independent thresholds can detect undervoltage and overvoltage conditions. The low 200 uA supply current per comparator helps limit continuous overhead, and the rail-to-rail input behavior supports threshold decisions near the lower operating range. Its open-collector outputs can trigger a host controller, charger, or isolation logic through pull-up resistors. Battery chemistry, transient protection, and the reference accuracy determine the final threshold tolerances.
Önerilen
Sensor Threshold Interface
The LM2903BIDSGR can translate a low-level sensor output into a logic event by comparing the sensing node with a reference voltage. Its input bias current of 3.5 nA minimizes loading on high-impedance sensors, while the low offset voltage helps preserve measurement precision. A 1 us response time supports relatively quick threshold transitions. For noisy industrial environments, filter the sensor path carefully and keep comparator inputs away from switching currents and relay wiring.
Önerilen
Window Voltage Comparator
Two LM2903BIDSGR channels can establish upper and lower limits for a monitored voltage, producing an overrange signal when the input moves outside either threshold. The dual architecture reduces the component count compared with discrete single comparators and preserves the low 200 uA supply-current figure per channel. Open-collector outputs can be combined through wired logic or read separately by a controller. Threshold matching and output timing should be checked across temperature before the circuit is used for precision production control.
Önerilen
Relaxation Oscillator
LM2903BIDSGR can form a relaxation oscillator by charging a timing capacitor through a resistor until the input crosses a feedback threshold. The 1 us response time provides a useful advantage over older comparator families with slower switching characteristics, while the open-collector output can source the timing current during part of each cycle. Component tolerances dominate frequency accuracy, so use a stable resistor and capacitor and verify operation across the intended temperature range.
Önerilen
Digital Control Signal Conditioning
LM2903BIDSGR is useful when an analog control signal must be converted into a logic-compatible fault or interlock indication. Its open-collector output supports pull-up operation in TTL, MOS, and CMOS systems, allowing the device to coexist with different logic families. The dual channels can handle two related decisions without duplicating supply pins. Keep pull-up values consistent with sink-current limits and the target logic rise time, and avoid placing high-current transitions near the high-impedance input nodes.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM2903BIDSGR — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün |
|---|---|
| Package | 8-WSON, 2 x 2 mm |
| Brand | Texas Instruments |
| Comparator Type | Dual differential comparator |
| Maximum Voltage Rating | 38 V |
| Differential Input Voltage Range | -38 V to +38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Supply Current | 200 uA per comparator |
| Response Time | 1 us |
| ESD Rating | 2 kV HBM |
| Output Type | Open collector |
| Input Common-Mode Behavior | Rail-to-rail |
Ana Farklılayıcılar
- Compact B-version dual comparator implementation (karşılaştırma:LM2903BIDR)
- Lower offset and bias than the original LM2903 generation (karşılaştırma:LM2903)
- Improved supply and switching characteristics (karşılaştırma:LM2903)
Tasarım Notları
Route each comparator input directly to its pins and keep the path short, away from power-switching nodes and high-current return paths. The 3.5 nA input bias current supports high-impedance sensing, but contamination, guard leakage, and nearby high-impedance traces can still create meaningful offsets. Place the input reference network close to the device and maintain a continuous ground reference beneath the analog section.
Connect the LM2903BIDSGR exposed thermal pad to the recommended ground-plane land using the manufacturer package land pattern. Provide uninterrupted ground copper beneath the device where practical to improve heat transfer and reduce return-path discontinuity. Follow the assembly guidelines for the 2 x 2 mm WSON package because fine-pitch leads require suitable paste volume, stencil apertures, and reflow control.
Do not treat the open-collector output as a actively driven logic output. Install a pull-up resistor to the correct logic supply, confirm its value against input current and output rise-time requirements, and ensure the receiving device permits an open-collector connection. Also observe the ±38 V differential input limit; input protection networks may affect offset, leakage, and response time.
Keep the open-collector pull-up resistor close to the output pin to minimize a high-impedance trace that can pick up noise. If the comparator controls a relay, solenoid, or long cable, use a driver stage rather than switching the load directly. Place protection and filtering components away from the precision input pins, and verify transient behavior at the connector or sensor boundary.
Uyumluluk Bilgisi
The device is identified as an industrial-grade dual comparator. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed for the exact ordering code through Texas Instruments. Industrial-grade status does not imply AEC-Q100 qualification.