LM2904PWRE4 - Dual 26V 700kHz Op Amp | Texas Instruments
MPN: LM2904PWRE4 ✓ AktifLM2904PWRE4 Genel Bakış
An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare or amplify a voltage. In the broader semiconductor hierarchy, the LM2904 belongs to the operational-amplifier family within analog amplifiers and signal-chain ICs. Its dual-circuit configuration allows two independent amplifier channels in one package, reducing board area when a design needs general-purpose voltage amplification, buffering, or signal conditioning.
The principal operating characteristics are its 26 V maximum supply capability, 700 kHz gain-bandwidth product, and 0.3 V/us slew rate. The 8-TSSOP package measures 0.173 inches, or 4.40 mm, in width according to the component listing. Low supply-current operation independent of supply voltage is also identified in the LM2904 datasheet, making the amplifier suitable for power-conscious analog systems that do not require high-speed precision amplification.
The LM2904 uses two independent amplifier sections for general-purpose analog functions. Its bandwidth supports moderate-frequency signal processing rather than high-speed video or RF amplification. A designer should verify gain-bandwidth, slew-rate, output-current capability, input common-mode range, input bias current, and output-voltage swing against the application because those operating limits define whether a conventional non-inverting or inverting topology can meet the required waveform and load conditions.
Typical uses include low-frequency sensor conditioning, audio preamplification, current-to-voltage conversion, general feedback control, and analog signal buffering. Because the IC contains two amplifiers, a single package can implement an instrumentation-style signal chain, a dual-channel filter, or a mixed configuration such as an active filter followed by an output driver. The 8-pin TSSOP footprint is also practical for compact mixed-signal boards.
PCB implementation should provide a short, low-impedance supply path to the device and route sensitive input and feedback connections away from switching nodes. Decoupling capacitors should be placed close to the supply pins, while input and feedback components should be positioned to minimize parasitic capacitance and leakage. Stable operation also depends on keeping output current and capacitive loading within the limits specified by the manufacturer datasheet.
This product page organizes the LM2904PWRE4 specifications, practical application guidance, same-package alternatives, and design considerations into an engineering-focused selection resource. It also highlights where additional device parameters must be checked directly in the manufacturer datasheet before a new analog board is released.
Drop-in alternatifler için LM2904PWRE4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM2904PWRE4 (aynı form faktörü ve ayağa oturma) — farklı olan Package, Amplifier Type, Packaging, Architecture.
LM2904PWRG3
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904PWRG4
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904BIPWR
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
LM2904BAIPWR
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
LM2904PW
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904PWRE4 Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | General Purpose |
| Number of Circuits | 2 circuits |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/us |
| Single-Supply Operation | Supported |
| Dual-Supply Operation | Supported |
| Paket | 8-TSSOP, 0.173 in (4.40 mm) width |
| Terminal Count | 8 terminals |
| Montaj Türü | Surface Mount |
| Packaging | Tape and Reel (TR) |
| Temperature Grade | Automotive |
| Besleme Akımı | 0.7 mA typical per amplifier |
| Input Offset Voltage | 3 mV maximum |
LM2904PWRE4 8-tssop, 0.173 in (4.40 mm) width Pin Yapısı Kılavuzu
LM2904PWRE4 (8-tssop, 0.173 in (4.40 mm) width paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: LM2904PWRE4.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LM2904PWRE4 için uygundur 6 uygulamas: Low-Frequency Sensor Signal Conditioning, Audio Preamplification, Active Filtering and Control Loops, Battery-Powered Analog Measurement, Current-to-Voltage Conversion, Automotive and Industrial Control Interfaces.
Low-Frequency Sensor Signal Conditioning
The LM2904PWRE4 fits sensor-conditioning stages that amplify small differential signals without requiring high-speed video performance. Its two amplifier channels can implement an instrumentation-style input stage and a second filtering or buffering channel, while the 700 kHz gain-bandwidth product provides bandwidth for common temperature, pressure, and position sensors. The 26 V maximum supply also permits operation from industrial rails above conventional 5 V levels. Before finalizing the circuit, verify the sensor output range against the LM2904 input common-mode limits, confirm adequate output swing, and place the amplifier inputs away from switching and high-current return paths to reduce coupled error.
Önerilen
Audio Preamplification
The LM2904PWRE4 can serve as a dual audio preamplifier for low-frequency source signals in compact analog equipment. Its 700 kHz gain-bandwidth product is appropriate for voice-band circuitry, and the dual-circuit package allows left and right channel amplification in one 8-TSSOP footprint. The 0.3 V/us slew rate should be checked against the largest expected input amplitude and target closed-loop gain to prevent unintended slew limiting. Use the package's supply pins with local high-frequency bypass capacitance, keep input and feedback traces short, and isolate the audio return path from motor, relay, and switching-converter currents to minimize audible coupling and channel imbalance.
Önerilen
Active Filtering and Control Loops
The two channels in the LM2904PWRE4 are useful for implementing active filters, integrators, or simple analog control loops where moderate bandwidth and stable operation are more important than high precision. A 700 kHz gain-bandwidth product gives the designer room to select closed-loop gains that preserve signal quality across the intended passband. Component tolerances around the feedback network directly influence cutoff frequency and gain accuracy, so use suitable resistor and capacitor grades and account for parasitic capacitance in the layout. Confirm that the intended operating frequency remains below the amplifier's small-signal and large-signal limits, and avoid driving excessively capacitive loads directly from the output.
Önerilen
Battery-Powered Analog Measurement
The LM2904PWRE4 is appropriate for portable measurement and monitoring circuits that need two analog channels while operating from a single supply. Its low supply-current drain, identified in the Texas Instruments datasheet as independent of supply voltage, supports power-conscious designs, and the device can also run from dual supplies when bipolar signal ranges are required. Because the operational amplifier may share a board with sensors, converters, and indicators, the designer should minimize quiescent loads elsewhere and avoid placing the analog channels near pulsed loads. Validate the complete battery operating range, common-mode headroom, and output swing at the lowest supply voltage before relying on the amplifier for accurate measurements.
Önerilen
Current-to-Voltage Conversion
The LM2904PWRE4 can convert a small current into a measurable voltage when paired with a suitable feedback resistor and low-leakage input network. Its 700 kHz gain-bandwidth product supports bandwidth requirements common to laboratory, instrumentation, and industrial current-measurement circuits, while the dual package allows a second channel for buffer, reference, or gain-stage functions. The precision of the conversion depends strongly on resistor accuracy, input bias current, input offset voltage, and leakage from the sensed node. Keep the high-impedance input path short, use guarding where condensation or board contamination is possible, and verify that the amplifier output remains inside its swing range at both light-load and full-scale conditions.
Önerilen
Automotive and Industrial Control Interfaces
The LM2904PWRE4 is identified as an automotive-temperature-grade ordering and can support low-frequency interface and control functions within appropriately specified environmental conditions. The dual amplifier arrangement is useful for motor-control feedback conditioning, actuator drive support, or supervisory analog channels, while the 26 V maximum supply provides compatibility with higher-voltage industrial systems. Automotive use requires confirmation of the exact temperature range, qualification status, and AEC-Q100 classification in the ordering information. Keep sensitive feedback connections away from inductive switching nodes, provide local supply bypassing, and test operation across supply transients and temperature corners because package qualification does not by itself validate the completed circuit.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM2904PWRE4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM2904PWR | LM2904PWRG4 | LM2904BIPWR | LM2904BAIPWR | LM2904PW |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP |
| Amplifier Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Maximum Supply Voltage | 26 V | 26 V | 26 V | 26 V | 26 V | 26 V |
| Gain-Bandwidth Product | 700 kHz | 700 kHz | 700 kHz | 700 kHz | 700 kHz | 700 kHz |
| Slew Rate | 0.3 V/us | 0.3 V/us | 0.3 V/us | 0.3 V/us | 0.3 V/us | 0.3 V/us |
Ana Farklılayıcılar
- Dual amplifier channels in a compact 8-TSSOP package (karşılaştırma:LM324)
- Higher bandwidth than the traditional LM324 performance class (karşılaştırma:LM324)
- Automotive-temperature-grade ordering (karşılaştırma:LM2904PWR)
Tasarım Notları
Place the supply-bypass capacitor immediately between the positive supply and ground pins, with the ground connection following the shortest practical return path. Keep the two amplifier inputs and their feedback components away from switching nodes, relay coils, motor traces, and high-current return paths. Because both channels share the same package and supply pins, coupling between channels can occur if their sensitive inputs run parallel near each other.
Treat the input and feedback networks as high-impedance analog paths when the source impedance is appreciable. Keep traces short, avoid routing them beneath digital or power-converter sections, and use a continuous ground plane where possible. The 700 kHz gain-bandwidth product is adequate for moderate-frequency signals, but excessive noise gain, capacitive loading, or high closed-loop gain can reduce stability and increase susceptibility to parasitic oscillation.
Verify the actual input voltage, output swing, and output-current demand for each amplifier channel. The 26 V value is a maximum supply rating, not a recommended operating point, and designers should include tolerance for supply variation and transient overshoot. If the device operates from a single rail, calculate whether the required output waveform remains above the lower output-swing limit throughout the signal cycle.
Do not infer complete electrical equivalence from a shared TSSOP footprint. Before substituting an LM2904-family ordering, compare the exact package drawing, pin names, temperature grade, qualification status, supply limits, offset voltage, input bias current, output swing, and load-current specification. A footprint-compatible part can still fail if revision-specific limits change the usable signal range or qualification requirements of the finished design.
Uyumluluk Bilgisi
The ordering listing identifies automotive temperature grade, but the verified records do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes in the Texas Instruments product page or manufacturer documentation before qualification.