Texas Instruments

LM358APW - Dual 30V 700kHz Op-Amp | TI | TSSOP-8

MPN: LM358APW ✓ Aktif
30 V Vdss 0.7 mA Id 8-TSSOP (PW) Package
MOQ: 1 |

LM358APW Genel Bakış

The Texas Instruments LM358APW is an industry-standard dual operational amplifier delivering two independent, internally compensated, high-gain op-amp channels rated for 30V supplies with a 700 kHz gain-bandwidth product, housed in an 8-pin TSSOP (PW) surface-mount package.

A dual operational amplifier is an integrated circuit that combines two complete op-amp stages on a single silicon die, sharing one power supply while keeping the signal paths fully independent. Within the amplification hierarchy, the op-amp sits above individual transistors as an analog signal-conditioning block, and the LM358 family is the archetypal general-purpose amplifier IC used throughout industrial, automotive-adjacent, and consumer electronics for decades.

Key features include a wide supply range that accepts single supplies from roughly 3V up to 30V or dual supplies, low supply-current drain of 0.7 mA (typical) that is essentially independent of supply voltage, and a common-mode input voltage range that includes ground. Ground-including common-mode input allows direct sensing of signals near 0V without negative rails, which is the defining advantage of the LM358 in single-supply systems.

Architecturally, the LM358 uses internally frequency-compensated bipolar stages, so no external compensation capacitors are required for unity-gain stability. The enhanced LM358A grade tightens key limits such as input offset voltage compared with the base LM358, giving designers additional accuracy margin while preserving the familiar behavior and pinout of the industry-standard part.

Typical applications include single-supply transducer signal conditioning, active filters and comparators in industrial controls, DC gain blocks and summing amplifiers in test equipment, and general-purpose amplification in battery-powered consumer devices where low quiescent drain extends operating life.

A key design consideration: the output stage is a classic bipolar design that can sink current to ground but does not pull close to the positive rail without a pull-up, so plan for rail-to-rail headroom limits near the supply maximum.

This page consolidates distributor sourcing channels, drop-in alternatives within the same TSSOP-8 footprint, engineering design notes, and parameter comparison data not typically found together in the manufacturer datasheet.

Drop-in alternatifler için LM358APW — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller LM358APW (aynı form faktörü ve ayağa oturma) — farklı olan Package, Amplifier Type, Gain-Bandwidth Product.

Texas Instruments
Package: 8-TSSOP, 4.40 mm width
Gain-Bandwidth Product: 700 kHz
İle Karşılaştır LM358APW →
Texas Instruments
Package: 8-TSSOP
Amplifier Type: General Purpose
Gain-Bandwidth Product: 700 kHz typical
İle Karşılaştır LM358APW →

LM358APWR

✅ Yerleştirme
📦 8-TSSOP (PW)
same die and TSSOP-8 footprint; tape-and-reel packing vs tube - electrically identical, param_match 100%

📋 Katalogda Olmayan Referans Alternatifi

LM2904APW

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-TSSOP (PW)
automotive/industrial grade sibling in same TSSOP-8 footprint; slightly different specified limits and temperature ratings (-10%)

📋 Katalogda Olmayan Referans Alternatifi

LM2904PW

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
Texas Instruments
📦 8-TSSOP (PW)
2 circuits · Dual general-purpose operational amplifier · 26 V · 700 kHz · 0.7 mA · Independent of supply voltage · Single supply or split supply · Includes ground

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

LM358APWE4

✅ Yerleştirme
Texas Instruments
📦 8-TSSOP (PW)
General Purpose · 2 circuits · 8-TSSOP · 4.40 mm · Surface Mount · Gull Wing · 8 terminals · Tube

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

LM358APW Maksimum Değerlendirmeler & Elektriksel Özellikler

Amplifier Configuration Dual (2 independent circuits)
Supply Voltage Rating 30 V
Gain Bandwidth Product 700 kHz
Supply Current (per amplifier, typ) 0.7 mA
Common-Mode Input Voltage Range Includes ground (negative rail)
Number of Channels 2
Amplifier Type General Purpose / Standard
Compensation Internally compensated (unity-gain stable)
Paket 8-TSSOP (PW)
Montaj Türü Surface Mount

LM358APW Pin Yapısı

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
Pin 1 OUT1 — Amplifier 1 output
Pin 2 IN1- — Amplifier 1 inverting input
Pin 3 IN1+ — Amplifier 1 non-inverting input
Pin 4 GND/V- — Ground or negative supply
Pin 5 IN2+ — Amplifier 2 non-inverting input
Pin 6 IN2- — Amplifier 2 inverting input
Pin 7 OUT2 — Amplifier 2 output
Pin 8 V+ — Positive supply

Tipik Uygulamalar

LM358APW için uygundur 6 uygulamas: Single-Supply Sensor Signal Conditioning, Industrial Control Active Filters, Battery-Powered Portable Instrumentation, Audio Preamp and Mixer Stages, Comparator and Level-Sensing Functions, Test and Measurement Gain Blocks.

🧩

Single-Supply Sensor Signal Conditioning

The LM358APW is a natural fit for single-supply transducer front ends because its common-mode input voltage range includes ground, allowing outputs from current shunts, thermistors, and pressure sensors referenced near 0V to be amplified directly without a negative rail or level-shifting stage. With a 30V supply rating the part tolerates industrial rail environments, while its 0.7 mA typical supply current keeps quiescent drain modest in battery-powered nodes. In a typical non-inverting gain stage the 700 kHz gain-bandwidth product comfortably covers sensor bandwidths of a few tens of kilohertz with stable gain. The trade-off is headroom: the output does not reach the positive rail, so keep the amplified signal range within the datasheet output swing limits at your load current.

🏭

Industrial Control Active Filters

In industrial controllers the LM358APW serves as an economical active filter and gain stage operating from a 24V-class single rail, which its 30V rating accommodates directly. The internally compensated bipolar design is unity-gain stable with no external compensation components, simplifying multi-stage Sallen-Key and multiple-feedback filter implementations. Its 700 kHz gain-bandwidth product supports filter cutoff frequencies up to roughly tens of kilohertz at moderate Q values before bandwidth-induced peaking becomes significant. The two independent channels on one die let one package implement, for example, a two-pole low-pass section plus an output scaler. Designers should bias inputs within the common-mode range and verify filter Q against the amplifier's open-loop gain at the cutoff frequency.

📱

Battery-Powered Portable Instrumentation

Portable instruments benefit from the LM358APW's combination of low quiescent drain and wide single-supply operation. At approximately 0.7 mA per amplifier the dual package draws around 1.4 mA quiescent, a modest share of a typical battery budget, while the ground-including input range permits direct interface to ground-referenced transducer outputs from a 3V-class single cell or lithium rail. The two channels allow one package to handle a difference amplifier followed by an active filter or comparator stage, reducing board area in the 8-pin TSSOP footprint. Engineers should note that precision at the low end is limited by the LM358A offset specification, so for microamp-level or microvolt-level measurements a precision amplifier family should be evaluated against the error budget.

🎧

Audio Preamp and Mixer Stages

The LM358APW provides cost-effective audio preamplification, summing, and level-shifting in consumer and light-commercial audio equipment. Its 700 kHz gain-bandwidth product covers the full audio band with usable open-loop gain at 20 kHz, supporting closed-loop gains in the tens with flat response, and the internally compensated design guarantees stability without external parts. The dual channels make it convenient for stereo paths or a summing bus plus output driver in a single TSSOP-8 package. Designers should observe two classic LM358 behaviors at audio extremes: crossover distortion in the output stage at light load, mitigated with a biasing pull-down resistor, and the output's inability to reach the positive rail, which sets maximum undistorted headroom for a given supply.

⚡

Comparator and Level-Sensing Functions

Although optimized as an amplifier, the LM358APW is widely used as a low-cost comparator and threshold detector because its output stage sinks substantial current to ground and the common-mode input range reaches the negative rail. Single-supply window comparators, undervoltage detectors, and sensor threshold alarms are classic deployments, with the two channels enabling a window comparator in one package. The 30V rating allows direct connection across industrial supply rails for monitoring. Key considerations are speed and saturation recovery: the 700 kHz bandwidth means switching transitions are slower than a dedicated comparator and recovery from saturation is not specified, so for microsecond-class response a true comparator device should be selected while the LM358APW remains appropriate for alarm-speed thresholds.

🔧

Test and Measurement Gain Blocks

Bench instruments, data-acquisition front ends, and general-purpose lab circuitry use the LM358APW as a DC gain block, summer, and buffer where moderate precision suffices. The enhanced LM358A grade tightens input offset limits relative to the base LM358, improving DC accuracy in instrumentation scaling stages, while the wide supply range supports circuits referenced to +/-15V dual rails or 24V single rails. The internally compensated topology accepts capacitive loads typical of coax and probe cabling with ordinary care, and unity-gain stability simplifies buffering of divider outputs. For channels requiring better offset, drift, or noise, engineers pair the LM358APW for auxiliary housekeeping functions with a precision amplifier in the critical signal path, balancing cost against accuracy per stage.

What are the key specifications of LM358APW that engineers should know?
The LM358APW is a Texas Instruments dual general-purpose operational amplifier in an 8-pin TSSOP package. Per the TI product page, it is rated for 30V supplies with a 700 kHz gain-bandwidth product. Each amplifier draws about 0.7 mA of supply current (typical), and the common-mode input voltage range includes ground, enabling direct ground-referenced sensing in single-supply circuits. The two channels are independent, high-gain, and internally compensated for unity-gain stability.
What is the supply voltage range of the LM358APW?
According to the Texas Instruments product page, the LM358APW is a 30-V operational amplifier, and the family datasheet states it operates over a wide range of supply voltages in either single-supply or dual-supply configurations. Because the supply-current drain is largely independent of supply voltage, the part behaves consistently across its supply range. For the exact minimum and maximum limits at temperature, consult the LM358A datasheet operating-conditions table before finalizing your design.
What is the pinout of the LM358APW in the TSSOP-8 package?
The LM358APW follows the industry-standard dual op-amp pinout for its 8-pin TSSOP (PW) package: pin 1 is amplifier 1 output, pin 2 is amplifier 1 inverting input, pin 3 is amplifier 1 non-inverting input, pin 4 is ground or negative supply, pin 5 is amplifier 2 non-inverting input, pin 6 is amplifier 2 inverting input, pin 7 is amplifier 2 output, and pin 8 is the positive supply. This matches the standard SOIC-8 and DIP-8 LM358 arrangement, so layouts can be ported between package families.
What is the bandwidth of the LM358APW?
The LM358APW has a gain-bandwidth product of 700 kHz, as stated on the Texas Instruments product page. This bandwidth is adequate for audio-range amplification, slow sensor conditioning, active filters below a few hundred kilohertz, and low-frequency control loops. For applications requiring multi-megahertz bandwidth or high slew rate, engineers typically select a faster amplifier family rather than the general-purpose LM358 series.
How much current does the LM358APW consume?
According to the LM358 family datasheet, the supply-current drain is approximately 0.7 mA per amplifier (typical) and is largely independent of supply voltage. For the dual package, total quiescent consumption is therefore on the order of 1.4 mA plus any load current. This low, stable drain is one reason the LM358 remains popular in battery-powered instrumentation and portable devices where modest precision is acceptable.
What is the difference between LM358APW and LM358APWR?
The LM358APW and LM358APWR contain the same die and share the same 8-pin TSSOP (PW) footprint; the difference is the packing format. The plain PW suffix is supplied in tube or tray quantity for prototype and low-volume assembly, while the PWR suffix is supplied in tape-and-reel packaging for automated production lines. Electrically and mechanically the parts are identical, so either ordering code can be used interchangeably on the same PCB land pattern.
LM358APW vs LM2904APW - which should I choose?
The LM2904APW is the automotive/industrial-grade sibling of the LM358APW in the same TSSOP-8 footprint. Both are dual 30V-class amplifiers with ground-including input common-mode range and similar supply current. Choose the LM2904APW when the design must survive harsher ambient conditions or needs the LM2904 grade's specified limits at elevated temperatures; choose the LM358APW for standard commercial and industrial applications where the enhanced LM358A electrical grade is sufficient. Confirm the datasheet temperature specifications for your worst-case ambient before selecting.
What is the best drop-in replacement for LM358APW?
The closest drop-in replacements are TI's own package and grade variants of the same family: LM358APWR (same die, tape-and-reel packing) is a 100% pin-to-pin and parametric match, and LM2904APW / LM2904PW provide the automotive-grade version in the identical TSSOP-8 footprint with minor specification differences. All of these solder onto the same PCB land pattern with no redesign. Always verify the detailed electrical limits in the current manufacturer datasheet before releasing a substitution in production.
What is the best cross-brand equivalent for LM358APW in TSSOP-8?
Several manufacturers produce LM358-compatible dual op-amps, and industry cross-reference guides list candidates such as RC4558-class dual amplifiers and domestic LM358 clones. However, cross-brand parts are commonly offered in DIP-8 or SOIC-8 rather than the TSSOP-8 (PW) body used by the LM358APW, so they are not mechanical drop-ins on this exact footprint. If a cross-brand substitute is required, verify both the pinout and the TSSOP-8 package outline against the manufacturer's mechanical drawing before committing the design.
Can the LM358APW sense signals near ground in single-supply operation?
Yes. According to the LM358 family datasheet, the common-mode input voltage range includes ground, which allows direct sensing of signals near 0V without a negative supply rail. This is the signature single-supply feature of the LM358 family and the main reason it is used for ground-referenced current shunts, transducer outputs, and level-shifting stages. Note that the output stage sinks close to ground but does not swing to the positive rail, so keep the upper headroom limit in mind.
Where can I download the LM358APW datasheet PDF?
The authoritative LM358APW documentation is available on the Texas Instruments website at the LM358 product page (ti.com/product/LM358), which links the current family datasheet covering the LM358A grade and the PW (TSSOP-8) package. The datasheet includes electrical characteristics, typical performance curves, application circuits, and the mechanical package drawing. Download the datasheet directly from TI to ensure you have the latest revision rather than third-party copies.
Where can I buy LM358APW online?
You can request the LM358APW directly through the Request a Quote form on this XAIPART page. Submitting your required quantity and delivery schedule returns pricing, stock position, and lead time for this exact Texas Instruments ordering code. For production volumes, the quote can also cover the tape-and-reel variant LM358APWR if that packing format suits your assembly line.
What is the price of the LM358APW?
Pricing for the LM358APW is issued through the Request a Quote form on this page, where unit price breaks by quantity, currency, and current stock are provided with your quotation. Pricing for commodity operational amplifiers changes frequently with market conditions, so a live quote is the reliable way to obtain an accurate, current figure for both prototype quantities and production volumes.
What is the lead time for LM358APW orders?
Lead time for the LM358APW depends on current stock position and manufacturer scheduling, so it is confirmed with your quotation. Submit the Request a Quote form on this page with your target quantity and required delivery date, and the quotation will return the available stock quantity, factory lead time if applicable, and shipping options. Standard packing for this code is tube or tray quantity; reel quantities are handled under the LM358APWR ordering code.
Is the LM358APW suitable for battery-powered sensor front ends?
Yes, the LM358APW fits battery-powered sensor front ends that operate from a single low-voltage rail. Its 0.7 mA typical supply current per amplifier limits quiescent drain, and the input common-mode range reaching ground lets a sensor output near 0V be amplified directly without level-shifting circuitry. It suits loads and filter frequencies within its 700 kHz gain-bandwidth. For micro-power designs where every microamp counts, TI's lower-power amplifier families are a better match, so compare supply current against your battery budget before finalizing.

Mühendislik referans verileri: LM358APW — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the LM358APW when you need the industry-standard dual op-amp behavior with enhanced A-grade accuracy in the TSSOP-8 footprint, on a single supply up to 30V, at minimal cost. Choose LM358APWR for identical silicon in tape-and-reel packing for automated production assembly, and LM358APWE4 when your build standard requires the eco-compatible ordering variant. Choose LM2904APW or LM2904PW when the end equipment is automotive or harsh-environment industrial and the LM2904 grade's specified temperature limits matter - all four solder onto the same land pattern. Select a different family when your requirement falls outside the LM358's envelope: rail-to-rail output swing needs a device such as the TS932, higher output current points to the TS922, and microamp-level power budgets or microvolt offset requirements call for a precision or nanopower amplifier rather than this general-purpose part.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün LM358APWR LM358APWE4 LM2904APW LM2904PW
Package 8-TSSOP (PW) 8-TSSOP (PW) - same 8-TSSOP (PW) - same 8-TSSOP (PW) - same 8-TSSOP (PW) - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Gain Bandwidth Product 700 kHz 700 kHz 700 kHz 700 kHz (family) 700 kHz (family)
Common-Mode Input Includes Ground Yes Yes Yes Yes (family feature) Yes (family feature)
Grade A grade (enhanced) A grade (enhanced) A grade (enhanced) LM2904A grade (automotive/industrial) Base LM2904 grade

Ana Farklılayıcılar

  • Enhanced A-grade electrical limits on the industry-standard LM358 die (karşılaştırma:LM2904PW)
  • Ground-including common-mode input range enables rail-free single-supply sensing (karşılaştırma:RC4558-class dual amplifiers)
  • Trade-off: 700 kHz bandwidth limits high-speed use (karşılaştırma:TS922AID)

Tasarım Notları

The LM358 output stage sources current weakly near the positive rail and exhibits crossover distortion at light load. In AC-coupled or comparator-style use, connect a pull-down resistor (for example, a few kilo-ohms to ground or a bias network) on the output to keep the output transistor class-AB biased and remove crossover artifacts. Also remember the output cannot reach V+; reserve roughly 1.5V of headroom at light load and more at higher source current, per the datasheet output voltage swing curves, or move to a rail-to-rail output device such as the TS932 for swing-critical stages.

Decouple V+ (pin 8) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a bulk 1 uF to 10 uF capacitor per board region. Although the LM358 is a low-speed bipolar part, shared-die crosstalk between the two amplifiers appears when one channel drives large load currents; keeping decoupling tight and routing the two channel grounds as star or ground-plane connections minimizes inter-channel coupling. In dual-supply designs ensure pin 4 is a genuine low-impedance negative rail, not a shared return carrying load current.

Use the standard dual-op-amp land pattern for the TSSOP-8 (PW) body, which matches the SOIC-8 footprint pitch so designs can be ported between package families. Keep input traces (pins 2, 3, 5, 6) short and guard high-impedance nodes with a ground ring to limit leakage; the input bias current of the bipolar front end, while small, is significant relative to megaohm divider networks. For single-supply operation referenced to ground, connect pin 4 directly to the analog ground plane with multiple vias to avoid common-mode sense errors near 0V.

Budget bandwidth conservatively: with a 700 kHz gain-bandwidth product, a closed-loop gain of 40 (32 dB) leaves roughly 17.5 kHz of small-signal bandwidth, and higher gains fall proportionally. Active filter stages should verify Q peaking against the open-loop gain remaining at the cutoff frequency; keep cutoff frequencies at least a decade below the closed-loop bandwidth for predictable response. In comparator use, add a small amount of positive hysteresis (for example, 10-50 mV via a resistor from output to the non-inverting input) to prevent output chatter near slow-moving thresholds.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

Compliance status should be confirmed on the TI product page for the exact ordering code; the LM358APWE4 variant exists specifically as the eco-compatible ordering option.

Veri doğrulanma tarihi: 2026-11-08 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

lm358apw datasheet lm358apw pinout lm358ap datasheet lm358ap pinout lm358apw datasheet pdf lm358apw equivalent lm358apw replacement lm358apw cross reference lm358apw vs lm2904apw lm358apw price lm358apw stock texas instruments lm358apw lm358 dual op amp tssop-8 pinout lm358 single supply op amp application circuit

İlgili Bileşenler ve Terimler

Texas Instruments LM358APW LM358APWR LM358APWE4 LM2904APW LM2904PW LM358 family dual operational amplifier op-amp operational amplifier general-purpose amplifier IC gain-bandwidth product common-mode input voltage range single-supply operation 8-TSSOP TSSOP-8 (PW) surface mount RoHS unity-gain stability sensor signal conditioning active filter supply current
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle