LM358APW - Dual 30V 700kHz Op-Amp | TI | TSSOP-8
料号: LM358APW ✓ 量产中LM358APW 概述
A dual operational amplifier is an integrated circuit that combines two complete op-amp stages on a single silicon die, sharing one power supply while keeping the signal paths fully independent. Within the amplification hierarchy, the op-amp sits above individual transistors as an analog signal-conditioning block, and the LM358 family is the archetypal general-purpose amplifier IC used throughout industrial, automotive-adjacent, and consumer electronics for decades.
Key features include a wide supply range that accepts single supplies from roughly 3V up to 30V or dual supplies, low supply-current drain of 0.7 mA (typical) that is essentially independent of supply voltage, and a common-mode input voltage range that includes ground. Ground-including common-mode input allows direct sensing of signals near 0V without negative rails, which is the defining advantage of the LM358 in single-supply systems.
Architecturally, the LM358 uses internally frequency-compensated bipolar stages, so no external compensation capacitors are required for unity-gain stability. The enhanced LM358A grade tightens key limits such as input offset voltage compared with the base LM358, giving designers additional accuracy margin while preserving the familiar behavior and pinout of the industry-standard part.
Typical applications include single-supply transducer signal conditioning, active filters and comparators in industrial controls, DC gain blocks and summing amplifiers in test equipment, and general-purpose amplification in battery-powered consumer devices where low quiescent drain extends operating life.
A key design consideration: the output stage is a classic bipolar design that can sink current to ground but does not pull close to the positive rail without a pull-up, so plan for rail-to-rail headroom limits near the supply maximum.
This page consolidates distributor sourcing channels, drop-in alternatives within the same TSSOP-8 footprint, engineering design notes, and parameter comparison data not typically found together in the manufacturer datasheet.
直接替换替代料: LM358APW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM358APW (相同外形与封装尺寸) ——差异在于 Package, Amplifier Type, Gain-Bandwidth Product.
LM358APWR
✅ 直接替换📋 参考替代料(不在目录中)
LM2904APW
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2904PW
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM358APWE4
✅ 直接替换联系询价
查看数据手册 →LM358APW 最大额定值与电气特性
| Amplifier Configuration | Dual (2 independent circuits) |
| Supply Voltage Rating | 30 V |
| Gain Bandwidth Product | 700 kHz |
| Supply Current (per amplifier, typ) | 0.7 mA |
| Common-Mode Input Voltage Range | Includes ground (negative rail) |
| Number of Channels | 2 |
| Amplifier Type | General Purpose / Standard |
| Compensation | Internally compensated (unity-gain stable) |
| 封装 | 8-TSSOP (PW) |
| 安装类型 | Surface Mount |
LM358APW 引脚配置
| 引脚 1 | OUT1 — Amplifier 1 output |
| 引脚 2 | IN1- — Amplifier 1 inverting input |
| 引脚 3 | IN1+ — Amplifier 1 non-inverting input |
| 引脚 4 | GND/V- — Ground or negative supply |
| 引脚 5 | IN2+ — Amplifier 2 non-inverting input |
| 引脚 6 | IN2- — Amplifier 2 inverting input |
| 引脚 7 | OUT2 — Amplifier 2 output |
| 引脚 8 | V+ — Positive supply |
典型应用
LM358APW 适用于 6 应用s: Single-Supply Sensor Signal Conditioning, Industrial Control Active Filters, Battery-Powered Portable Instrumentation, Audio Preamp and Mixer Stages, Comparator and Level-Sensing Functions, Test and Measurement Gain Blocks.
Single-Supply Sensor Signal Conditioning
The LM358APW is a natural fit for single-supply transducer front ends because its common-mode input voltage range includes ground, allowing outputs from current shunts, thermistors, and pressure sensors referenced near 0V to be amplified directly without a negative rail or level-shifting stage. With a 30V supply rating the part tolerates industrial rail environments, while its 0.7 mA typical supply current keeps quiescent drain modest in battery-powered nodes. In a typical non-inverting gain stage the 700 kHz gain-bandwidth product comfortably covers sensor bandwidths of a few tens of kilohertz with stable gain. The trade-off is headroom: the output does not reach the positive rail, so keep the amplified signal range within the datasheet output swing limits at your load current.
推荐
Industrial Control Active Filters
In industrial controllers the LM358APW serves as an economical active filter and gain stage operating from a 24V-class single rail, which its 30V rating accommodates directly. The internally compensated bipolar design is unity-gain stable with no external compensation components, simplifying multi-stage Sallen-Key and multiple-feedback filter implementations. Its 700 kHz gain-bandwidth product supports filter cutoff frequencies up to roughly tens of kilohertz at moderate Q values before bandwidth-induced peaking becomes significant. The two independent channels on one die let one package implement, for example, a two-pole low-pass section plus an output scaler. Designers should bias inputs within the common-mode range and verify filter Q against the amplifier's open-loop gain at the cutoff frequency.
推荐
Battery-Powered Portable Instrumentation
Portable instruments benefit from the LM358APW's combination of low quiescent drain and wide single-supply operation. At approximately 0.7 mA per amplifier the dual package draws around 1.4 mA quiescent, a modest share of a typical battery budget, while the ground-including input range permits direct interface to ground-referenced transducer outputs from a 3V-class single cell or lithium rail. The two channels allow one package to handle a difference amplifier followed by an active filter or comparator stage, reducing board area in the 8-pin TSSOP footprint. Engineers should note that precision at the low end is limited by the LM358A offset specification, so for microamp-level or microvolt-level measurements a precision amplifier family should be evaluated against the error budget.
推荐
Audio Preamp and Mixer Stages
The LM358APW provides cost-effective audio preamplification, summing, and level-shifting in consumer and light-commercial audio equipment. Its 700 kHz gain-bandwidth product covers the full audio band with usable open-loop gain at 20 kHz, supporting closed-loop gains in the tens with flat response, and the internally compensated design guarantees stability without external parts. The dual channels make it convenient for stereo paths or a summing bus plus output driver in a single TSSOP-8 package. Designers should observe two classic LM358 behaviors at audio extremes: crossover distortion in the output stage at light load, mitigated with a biasing pull-down resistor, and the output's inability to reach the positive rail, which sets maximum undistorted headroom for a given supply.
推荐
Comparator and Level-Sensing Functions
Although optimized as an amplifier, the LM358APW is widely used as a low-cost comparator and threshold detector because its output stage sinks substantial current to ground and the common-mode input range reaches the negative rail. Single-supply window comparators, undervoltage detectors, and sensor threshold alarms are classic deployments, with the two channels enabling a window comparator in one package. The 30V rating allows direct connection across industrial supply rails for monitoring. Key considerations are speed and saturation recovery: the 700 kHz bandwidth means switching transitions are slower than a dedicated comparator and recovery from saturation is not specified, so for microsecond-class response a true comparator device should be selected while the LM358APW remains appropriate for alarm-speed thresholds.
推荐
Test and Measurement Gain Blocks
Bench instruments, data-acquisition front ends, and general-purpose lab circuitry use the LM358APW as a DC gain block, summer, and buffer where moderate precision suffices. The enhanced LM358A grade tightens input offset limits relative to the base LM358, improving DC accuracy in instrumentation scaling stages, while the wide supply range supports circuits referenced to +/-15V dual rails or 24V single rails. The internally compensated topology accepts capacitive loads typical of coax and probe cabling with ordinary care, and unity-gain stability simplifies buffering of divider outputs. For channels requiring better offset, drift, or noise, engineers pair the LM358APW for auxiliary housekeeping functions with a precision amplifier in the critical signal path, balancing cost against accuracy per stage.
推荐
推荐产品汇总
工程参考数据: LM358APW ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM358APWR | LM358APWE4 | LM2904APW | LM2904PW |
|---|---|---|---|---|---|
| Package | 8-TSSOP (PW) | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same | 8-TSSOP (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Gain Bandwidth Product | 700 kHz | 700 kHz | 700 kHz | 700 kHz (family) | 700 kHz (family) |
| Common-Mode Input Includes Ground | Yes | Yes | Yes | Yes (family feature) | Yes (family feature) |
| Grade | A grade (enhanced) | A grade (enhanced) | A grade (enhanced) | LM2904A grade (automotive/industrial) | Base LM2904 grade |
关键差异点
- Enhanced A-grade electrical limits on the industry-standard LM358 die (对比 LM2904PW)
- Ground-including common-mode input range enables rail-free single-supply sensing (对比 RC4558-class dual amplifiers)
- Trade-off: 700 kHz bandwidth limits high-speed use (对比 TS922AID)
设计说明
The LM358 output stage sources current weakly near the positive rail and exhibits crossover distortion at light load. In AC-coupled or comparator-style use, connect a pull-down resistor (for example, a few kilo-ohms to ground or a bias network) on the output to keep the output transistor class-AB biased and remove crossover artifacts. Also remember the output cannot reach V+; reserve roughly 1.5V of headroom at light load and more at higher source current, per the datasheet output voltage swing curves, or move to a rail-to-rail output device such as the TS932 for swing-critical stages.
Decouple V+ (pin 8) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a bulk 1 uF to 10 uF capacitor per board region. Although the LM358 is a low-speed bipolar part, shared-die crosstalk between the two amplifiers appears when one channel drives large load currents; keeping decoupling tight and routing the two channel grounds as star or ground-plane connections minimizes inter-channel coupling. In dual-supply designs ensure pin 4 is a genuine low-impedance negative rail, not a shared return carrying load current.
Use the standard dual-op-amp land pattern for the TSSOP-8 (PW) body, which matches the SOIC-8 footprint pitch so designs can be ported between package families. Keep input traces (pins 2, 3, 5, 6) short and guard high-impedance nodes with a ground ring to limit leakage; the input bias current of the bipolar front end, while small, is significant relative to megaohm divider networks. For single-supply operation referenced to ground, connect pin 4 directly to the analog ground plane with multiple vias to avoid common-mode sense errors near 0V.
Budget bandwidth conservatively: with a 700 kHz gain-bandwidth product, a closed-loop gain of 40 (32 dB) leaves roughly 17.5 kHz of small-signal bandwidth, and higher gains fall proportionally. Active filter stages should verify Q peaking against the open-loop gain remaining at the cutoff frequency; keep cutoff frequencies at least a decade below the closed-loop bandwidth for predictable response. In comparator use, add a small amount of positive hysteresis (for example, 10-50 mV via a resistor from output to the non-inverting input) to prevent output chatter near slow-moving thresholds.
合规信息
Compliance status should be confirmed on the TI product page for the exact ordering code; the LM358APWE4 variant exists specifically as the eco-compatible ordering option.