Texas Instruments

MAX232EIPWG4 - Dual RS-232 Interface | Texas Instruments

MPN: MAX232EIPWG4 ✓ Aktif
5 V Vdss TSSOP-16 Package
MOQ: 1 |

MAX232EIPWG4 Genel Bakış

The Texas Instruments MAX232EIPWG4 is a dual RS-232 driver/receiver interface IC with two transmit channels, two receive channels, and IEC 61000-4-2 electrostatic-discharge protection. It operates from a single 5 V supply, supports data rates up to 120 kbit/s, and uses 1.0 uF charge-pump capacitors. The device is packaged in a 16-pin TSSOP package. According to the MAX232EIPWG4 datasheet, it meets or exceeds TIA/RS-232-F and ITU Recommendation V.28 while tolerating input levels up to plus or minus 30 V.

An RS-232 transceiver is an interface IC that translates logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic levels. It belongs to the interface IC hierarchy, connects digital equipment to serial communication equipment, and handles the voltage conversion that the RS-232 standard requires. The MAX232EIPWG4 uses an internal charge-pump circuit to generate the positive and negative voltages needed by its two RS-232 drivers.

Key features include two integrated drivers, two integrated receivers, operation from one 5 V power supply, 120 kbit/s operation, plus or minus 30 V receiver input capability, and IEC 61000-4-2 protection. The protected receiver inputs are particularly useful where cables connect to external equipment and electrostatic discharge may enter the system through the serial connector. Its integrated charge-pump design simplifies interface implementation compared with discrete level-shifting networks.

Technically, the MAX232EIPWG4 combines RS-232 line drivers, RS-232 receivers, and regulated charge pumps in one package. The 1.0 uF charge-pump capacitors establish the internal voltage rails used by the drivers. Receiver inputs tolerate plus or minus 30 V levels, allowing the interface to remain connected to standard RS-232 ports when the local logic supply is 5 V. The device is intended for industrial-temperature operation, with a gull-wing TSSOP package suited to conventional surface-mount PCB assembly.

Typical uses include industrial serial-control panels, test and measurement equipment, point-of-sale terminals, service-console links, and data-acquisition equipment. The dual-channel arrangement allows one device to support two RS-232 ports when both transmit and receive lines are required. Its 120 kbit/s capability is appropriate for legacy serial protocols, configuration interfaces, and equipment-control links rather than modern high-speed Ethernet or USB communication.

PCB implementation should follow the manufacturer datasheet's charge-pump capacitor connection and keep the MAX232EIPWG4 close to the RS-232 connector. Confirm capacitor voltage rating, polarity, and placement against the datasheet requirements. Protect connector-side routing from unintended board contamination, and maintain suitable ground-return continuity between connected equipment. For a new design, verify that the remote equipment still uses RS-232 rather than RS-422, RS-485, or another differential interface.

This page combines the device's stated electrical characteristics with application guidance, package-aware selection criteria, and verified drop-in alternatives. It also distinguishes true same-footprint replacements from parts that merely perform the same RS-232 function but require a different PCB footprint.

Drop-in alternatifler için MAX232EIPWG4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu ürüne yer değiştirme seçenekleri mevcut değil.

Alternatifleri Talep Edin

MAX232EIPWG4 Özellikler

Product Type Dual RS-232 driver/receiver interface IC
Number of Drivers 2
Number of Receivers 2
Besleme Gerilimi 5 V
Maximum Data Rate 120 kbit/s
Charge-Pump Capacitor Value 1.0 uF
Receiver Input Voltage Range -30 V to +30 V
ESD Protection Standard IEC 61000-4-2
RS-232 Compliance TIA/RS-232-F
ITU Recommendation V.28
Temperature Grade Industrial
Package Type TSSOP-16
Terminal Count 16
Terminal Form Gull wing
Package Shape Rectangular
Montaj Türü Surface mount

MAX232EIPWG4 rectangular Pin Yapısı Kılavuzu

MAX232EIPWG4 (rectangular paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

rectangular paket pin çizelgesi için MAX232EIPWG4

Ayrıntılı pin çıkış verisi mevcut değil: MAX232EIPWG4.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

MAX232EIPWG4 için uygundur 6 uygulamas: Industrial Serial Control Panels, Test and Measurement Equipment, Point-of-Sale Terminals, Data-Acquisition Systems, Service and Configuration Consoles, Instrumentation and Process-Control Links.

🏭

Industrial Serial Control Panels

The MAX232EIPWG4 fits a dual-channel industrial control panel that must communicate with legacy RS-232 equipment through a single 5 V logic supply. Its two drivers and two receivers support two bidirectional serial links, while operation up to 120 kbit/s covers many configuration and service protocols. The plus or minus 30 V receiver input capability and IEC 61000-4-2 protection add margin at connector-facing inputs. Place the device near the serial connectors, route the charge-pump network compactly, and verify the industrial temperature range against the complete system enclosure.

🔧

Test and Measurement Equipment

The MAX232EIPWG4 is suitable for test and measurement instruments that expose a legacy RS-232 configuration or service port while operating from 5 V. Two integrated driver/receiver channels can reduce the component count when the instrument supports multiple serial links. Its 120 kbit/s rate is appropriate for command consoles, calibration routines, and low-speed data-transfer interfaces. The protected receiver inputs help manage electrostatic-discharge exposure associated with user-accessible cabling, although the connector, chassis grounding, and cable design remain important parts of the protection strategy.

🖥️

Point-of-Sale Terminals

The MAX232EIPWG4 can support RS-232 peripherals commonly found around point-of-sale systems, including scales, printers, or customer displays with legacy serial interfaces. Its dual-channel structure allows two complete bidirectional ports when both directions are needed, and its single 5 V supply simplifies integration with equipment that already uses 5 V logic. The 120 kbit/s data rate covers many short-distance peripheral protocols. Place the transceiver close to the connector, maintain a continuous signal-ground path, and check whether the attached peripheral requires hardware handshaking before allocating the available pins.

📡

Data-Acquisition Systems

The MAX232EIPWG4 is a practical interface between a 5 V data-acquisition controller and external RS-232 instruments. Two receivers can collect status or command information from separate ports, while the drivers return configuration and control data. The 120 kbit/s limit suits low-bandwidth acquisition-control traffic rather than continuous high-rate sensor streaming. The integrated IEC 61000-4-2 protection is useful when cables enter the enclosure from uncontrolled environments, but engineers should still use a suitable connector, short unprotected stub strategy, and chassis-to-signal-ground design appropriate to the installation.

🔧

Service and Configuration Consoles

The MAX232EIPWG4 is appropriate for embedded equipment with a service port used during installation, calibration, or maintenance. A 120 kbit/s RS-232 channel provides sufficient bandwidth for command exchanges, diagnostic output, and firmware-transfer workflows, while the dual-driver/receiver arrangement permits two ports on space-constrained boards. The single 5 V operating supply aligns with many embedded control platforms. Engineers should document boot-loader behavior, isolate the service connector when it is not in use, and test the interface with the actual service cable because capacitance and connector geometry can influence signal integrity.

⚡

Instrumentation and Process-Control Links

The MAX232EIPWG4 can bridge a compact controller to legacy RS-232 instrumentation used in process-control or laboratory systems. Its two independent channels reduce the footprint needed for separate single-channel transceivers, and the 5 V supply requirement supports embedded control designs. The plus or minus 30 V receiver input range is useful for standard RS-232 signaling, while the stated ESD protection helps at externally cabled interfaces. Verify grounding and isolation requirements, especially when connecting equipment at different earth potentials, because the IC does not by itself provide galvanic isolation.

What is the MAX232EIPWG4?
The MAX232EIPWG4 is a Texas Instruments dual RS-232 driver/receiver interface IC with two transmit channels and two receive channels. It operates from a single 5 V supply, supports rates up to 120 kbit/s, and is available in a 16-pin TSSOP package. According to the MAX232EIPWG4 datasheet, it also meets or exceeds TIA/RS-232-F and ITU Recommendation V.28.
Where can I download the MAX232EIPWG4 datasheet PDF?
The MAX232EIPWG4 datasheet PDF is available through the Texas Instruments product documentation and from the linked manufacturer-document mirror in the datasheet field on this page. The document describes the dual RS-232 driver/receiver, the 1.0 uF charge-pump capacitors, plus or minus 30 V receiver inputs, and IEC 61000-4-2 protection. Use the pin-description and typical-application sections when assigning PCB signals.
Where can I find the MAX232EIPWG4 pinout?
The MAX232EIPWG4 pinout is defined in the pin-configuration and pin-description tables of the manufacturer datasheet. The device has 16 TSSOP terminals, including supply, ground, receiver outputs, driver inputs, and RS-232 line terminals. Assign the PCB footprint from the datasheet pin table rather than relying on a generic MAX232 drawing, because ordering suffixes and package variants can use different pin numbers.
What are the key specifications of MAX232EIPWG4 engineers should know?
The principal MAX232EIPWG4 specifications are a single 5 V supply, two drivers, two receivers, 120 kbit/s maximum data rate, 1.0 uF charge-pump capacitors, plus or minus 30 V receiver input capability, and IEC 61000-4-2 protection. The manufacturer datasheet also identifies TIA/RS-232-F and ITU Recommendation V.28 compliance. The device uses a 16-terminal industrial-temperature TSSOP package.
What is the MAX232EIPWG4 vs MAX232IN difference?
The MAX232EIPWG4 uses a 16-pin TSSOP package, while the MAX232IN comparison result identifies a 16-pin SOIC package. Therefore, MAX232IN is not a footprint-compatible drop-in replacement for this target despite offering a related dual RS-232 interface function. A SOIC-to-TSSOP change requires a different PCB footprint and cannot be treated as a board-level substitution.
What can replace MAX232EIPWG4?
A valid MAX232EIPWG4 replacement must use the same 16-pin TSSOP footprint, preserve pin-to-pin connections, and provide comparable RS-232 electrical performance. No additional pin-compatible replacement is established by the available manufacturer and cross-reference documentation. Request a quote for the original Texas Instruments part, and validate any proposed substitute against the manufacturer pin and electrical tables before changing a released PCB.
When should I choose MAX232EIPWG4 over another RS-232 transceiver?
Choose the MAX232EIPWG4 when the design needs two RS-232 channels, a single 5 V supply, operation up to 120 kbit/s, and IEC 61000-4-2-protected receiver inputs in a 16-pin TSSOP footprint. A functionally similar SOIC or SOIC-W device may require a different PCB layout, while a transceiver with a different supply rating or ESD arrangement may require different external components.
Is MAX232EIPWG4 suitable for industrial serial equipment?
The MAX232EIPWG4 is identified as an industrial-temperature RS-232 interface IC and is suitable for industrial equipment when the complete system remains within its specified operating-temperature limits. Its dual-channel arrangement supports two bidirectional RS-232 links, while plus or minus 30 V receiver inputs and IEC 61000-4-2 protection improve interface robustness. Confirm the full temperature range and system ESD requirements in the manufacturer datasheet.
What protection does MAX232EIPWG4 provide?
The MAX232EIPWG4 provides IEC 61000-4-2 electrostatic-discharge protection on its receiver interface and accepts input voltages up to plus or minus 30 V. The protection does not remove the need for careful connector placement, grounding, and enclosure design. The manufacturer datasheet should be consulted for the applicable test conditions and whether additional external protection is required for a particular system.
How do I design the charge-pump capacitors for MAX232EIPWG4?
Use 1.0 uF charge-pump capacitors at the connections identified in the manufacturer datasheet and observe its placement, tolerance, and voltage-rating requirements. Keep the charge-pump loop compact because long traces can increase radiated noise and reduce operating margin. Confirm capacitor polarity and derating against the actual capacitor datasheet, and verify the final layout against the manufacturer's recommended PCB pattern.
Can MAX232EIPWG4 operate from a 3.3 V supply?
The MAX232EIPWG4 is specified to operate from a single 5 V supply. It should not be assumed to support 3.3 V operation because the stated supply requirement is 5 V. A 3.3 V system requiring an RS-232 interface should instead use a transceiver explicitly specified for 3.3 V operation, with a suitable package and compatible logic thresholds.
What is the maximum RS-232 data rate of MAX232EIPWG4?
The MAX232EIPWG4 supports data rates up to 120 kbit/s according to the manufacturer datasheet. This rate suits legacy serial-control and configuration protocols, including equipment links that do not require modern high-speed serial bandwidth. Cable length, capacitance, loading, and the connected equipment can still affect usable throughput, so validate the complete channel in the intended environment.
Where can I buy MAX232EIPWG4 online?
The MAX232EIPWG4 can be requested through the Request a Quote form on this page. The form is the appropriate channel for current availability, lead time, and order handling without relying on potentially stale price information. For production procurement, request the exact Texas Instruments MPN MAX232EIPWG4 and confirm industrial-temperature grade, 16-pin TSSOP packaging, and delivery requirements in the order response.
What is the lead time for MAX232EIPWG4?
The current manufacturer lead time for MAX232EIPWG4 should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, inventory position, and manufacturing conditions, so a historical listing does not represent a current scheduling commitment. Include your required quantity, date code preference, target price, and approved-vendor status when submitting the request.
Is MAX232EIPWG4 in stock and what does it cost?
Current stock status and commercial terms for MAX232EIPWG4 are available through the Request a Quote form on this page. The form provides a direct path for a current quotation and lead-time confirmation. Engineers should also include the required quantity, packaging preference, target date, and any approved sourcing requirements so the commercial response matches the production plan.

Mühendislik referans verileri: MAX232EIPWG4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the MAX232EIPWG4 when the PCB requires a compact 16-pin TSSOP RS-232 interface operating from 5 V, with two bidirectional channels, receiver inputs tolerant to plus or minus 30 V, and IEC 61000-4-2 protection. It is well matched to legacy industrial control, service, test, and point-of-sale links operating at or below 120 kbit/s. Do not select a SOIC-W or SOIC alternative solely because it performs the same RS-232 function; the footprint and pin assignments must match the existing layout. A newly designed 3.3 V system should instead use an interface explicitly rated for 3.3 V rather than assuming this 5 V part can operate from a lower rail. Equipment requiring galvanic isolation, modern high-speed networking, or differential RS-485 also needs a different interface architecture.

Ana Farklılayıcılar

  • Combines two complete RS-232 channels with protected receiver inputs (karşılaştırma:Single-channel RS-232 interface)
  • Supports legacy serial data rates up to 120 kbit/s (karşılaştırma:Higher-bandwidth RS-232 transceiver)
  • Uses a compact 16-pin TSSOP footprint (karşılaştırma:MAX232IN)

Tasarım Notları

Use the pin-configuration table in the manufacturer datasheet when creating the PCB symbol and footprint. Place the two 1.0 uF charge-pump capacitors close to their designated pins, minimize the loop area, and route the RS-232 connector-side nets away from sensitive analog and high-speed digital traces. Confirm the exposed package dimensions and terminal numbering against the selected 16-pin TSSOP drawing before releasing artwork.

Do not treat a functionally similar SOIC or SOIC-W RS-232 transceiver as a board-level replacement. The available MAX232IN comparison identifies a 16-pin SOIC package, whereas MAX232EIPWG4 uses 16-pin TSSOP; changing between them requires a different footprint and pin assignment. Confirm connector gender, signal-ground wiring, and remote-device logic levels before selecting the interface IC.

Keep the RS-232 receive paths away from switching nodes and long parallel runs of high-current power wiring. Maintain a continuous ground reference between the board and connected equipment, and apply the manufacturer's charge-pump capacitor placement guidance. If a cable can be touched by an operator, supplement the IC's IEC 61000-4-2 receiver protection with appropriate connector, enclosure, and grounding measures.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The manufacturer documentation identifies IEC 61000-4-2 protection, TIA/RS-232-F compliance, and ITU Recommendation V.28. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated.

Veri doğrulanma tarihi: 2026-11-09 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

MAX232EIPWG4 datasheet MAX232EIPWG4 pinout MAX232EIPWG4 datasheet pdf MAX232EIPWG4 equivalent MAX232EIPWG4 replacement MAX232EIPWG4 cross reference MAX232EIPWG4 footprint MAX232EIPWG4 application circuit MAX232EIPWG4 price MAX232EIPWG4 stock Texas Instruments MAX232EIPWG4 MAX232EIPWG4 vs MAX232IN

İlgili Bileşenler ve Terimler

Texas Instruments MAX232EIPWG4 MAX232IN RS-232 RS-232 transceiver dual RS-232 driver/receiver interface IC line driver line receiver charge-pump capacitor TIA/RS-232-F ITU Recommendation V.28 IEC 61000-4-2 electrostatic-discharge protection TSSOP-16 TSSOP package family surface-mount technology SMD single 5 V supply 120 kbit/s plus or minus 30 V input industrial-grade serial communication legacy serial interface
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle