MAX3243CDW - 3-5.5V 250kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3243CDW ✓ AktifMAX3243CDW Genel Bakış
An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into balanced, single-ended RS-232 line voltages and converts received line voltages back into logic levels. The MAX3243 belongs to the multi-channel transceiver class within the broader hierarchy of interface ICs, serial communication controllers, and semiconductor signal-conditioning devices. Its integrated driver and receiver channels reduce the number of separate components required in legacy serial ports, industrial control links, and service interfaces.
The three-driver and five-receiver configuration allows one connector to support several RS-232 signals without using five unrelated transceivers. Operation from 3 V to 5.5 V makes the device suitable for systems that use 3.3 V or 5 V control electronics. The specified 250 kbps data rate covers legacy serial communication while providing useful margin below faster RS-485 interfaces. The ±15 kV HBM protection rating strengthens the connector-side interface against electrostatic discharge events.
Internally, the MAX3243 uses charge-pump circuitry to generate the voltage levels required by RS-232 transmitters. The three drivers add the required line signal, while the five receivers detect and condition incoming signals. The asymmetric channel count supports designs in which a system transmits on three lines and monitors five incoming lines, including handshake, status, and acknowledgment signals.
Typical uses include industrial control panels, data-acquisition equipment, instrumentation, embedded service consoles, and legacy peripheral connections. It is particularly suitable where a modern controller must retain compatibility with an established RS-232 port but also needs a compact multi-channel interface. A single transceiver can consolidate several point-to-point or multidrop-compatible links when the system designer follows the RS-232 topology correctly.
PCB design should keep the charge-pump and interface circuitry on the manufacturer's recommended layout and provide the required bypass capacitance close to the supply pins. Keep serial traces short, provide the intended common-mode return path, and use suitable protection networks where cables leave the enclosure. Do not infer that the HBM rating eliminates the need for external surge protection on long or unprotected cable runs.
This product page consolidates the manufacturer specifications, channel configuration, source links, drop-in comparison, and implementation guidance into a design-focused reference. Engineers can use the comparison and selection guidance to evaluate the MAX3243CDW alongside pin-compatible alternatives, while the application notes clarify where its 28-pin SOIC interface fits in embedded and industrial serial systems.
Drop-in alternatifler için MAX3243CDW — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
MAX3243EWR
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
SN65C3243DBR
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MAX3243CDW Özellikler
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Number of Drivers | 3 |
| Number of Receivers | 5 |
| ESD Protection | ±15 kV HBM |
| Paket | 28-pin SOIC |
| Montaj Türü | Surface mount |
| Signal Standard | RS-232 |
MAX3243CDW 28-pin soic Pin Yapısı Kılavuzu
MAX3243CDW (28-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MAX3243CDW.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MAX3243CDW için uygundur 6 uygulamas: Industrial Control Panel Interface, Data Acquisition Instrument, Legacy Peripheral Connection, Embedded Service Console, Instrumentation Communication Hub, RS-232 Test and Measurement Adapter.
Industrial Control Panel Interface
The MAX3243CDW fits industrial control panels that retain an RS-232 service port while also exchanging status and acknowledgment signals. Its three drivers can support outgoing command or control lines, and five receivers can monitor incoming equipment states through a 28-pin SOIC. The 3 V to 5.5 V supply range supports both 3.3 V and 5 V embedded controller platforms. At a maximum rate of 250 kbps, it is appropriate for legacy RS-232 service traffic rather than high-speed differential data. Its ±15 kV HBM interface protection adds useful robustness, although cable-side surge protection and proper grounding remain important in industrial installations.
Önerilen
Data Acquisition Instrument
The MAX3243CDW can consolidate legacy RS-232 command, measurement, and status lines in a data-acquisition instrument. A single 28-pin SOIC provides three transmit channels and five receive channels, reducing the board area needed for separate line-driver and receiver ICs. Its 250 kbps maximum rate is suitable for configuration commands and periodic measurement results. Operation from 3 V to 5.5 V allows the same transceiver to be used beside modern 3.3 V control logic or conventional 5 V interface circuits. Designers should follow the manufacturer bypass-capacitor and charge-pump layout while adding suitable protection if the instrument cable exits the enclosure.
Önerilen
Legacy Peripheral Connection
The MAX3243CDW is useful for embedded systems that must communicate with a legacy printer, scanner, controller, or service peripheral through RS-232. Three drivers and five receivers permit simultaneous control, status, and handshake signals rather than limiting the system to a single transmit-and-receive pair. The device supports a 3 V to 5.5 V supply, so it can fit both modern and older system architectures. Its 250 kbps ceiling covers typical peripheral command protocols while remaining within the intended RS-232 operating class. Verify connector signal assignments and ground continuity, and avoid treating the internal ESD rating as a substitute for enclosure-level cable protection.
Önerilen
Embedded Service Console
The MAX3243CDW supports embedded service consoles that need several communication lines for diagnostics, configuration, and status reporting. Three drivers can carry commands or control signals toward a service host, while five receivers can bring back acknowledgment and diagnostic signals. The 28-pin SOIC package supports compact board layouts, and the 3 V to 5.5 V range accommodates common embedded supply levels. The 250 kbps maximum data rate is appropriate for textual menus, diagnostic logs, and low-bandwidth firmware service protocols. Keep the RS-232 traces short, implement the manufacturer-recommended bypass network, and assess whether the external cable requires additional surge or ESD protection.
Önerilen
Instrumentation Communication Hub
The MAX3243CDW can serve as an RS-232 communication hub within a multi-instrument test system. Its asymmetric 3/5 channel arrangement allows three outgoing control or status paths and five incoming measurement or ready signals to share one transceiver footprint. The device’s 250 kbps rate matches many legacy instrumentation protocols, while the 3 V to 5.5 V operating range simplifies interoperability with mixed-generation test equipment. Because RS-232 is a single-ended interface, each connected circuit must share an appropriate signal ground. Route driver and receiver paths to avoid noisy digital sources, follow the charge-pump layout, and add external protection for long laboratory or factory cables.
Önerilen
RS-232 Test and Measurement Adapter
The MAX3243CDW is appropriate for a compact RS-232 test adapter that bridges a modern controller to equipment using multiple legacy signals. Three drivers support control and status outputs, and five receivers support response and handshake inputs, all within a 28-pin SOIC. The device operates from 3 V to 5.5 V and reaches 250 kbps, which is appropriate for many instrument-control protocols. In an adapter, preserve the connector’s RS-232 signal and ground assignments rather than treating it as an RS-485 or TTL interface. Validate every pin against the manufacturer datasheet, provide local bypass capacitance, and include appropriate surge protection for cables connected outside the test bench.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MAX3243CDW — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MAX3243EWR | SN65C3243DBR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin SOIC | 28-pin SOIC | 28-pin SOIC |
| Number of Drivers | 3 | 3 | 3 |
| Number of Receivers | 5 | 5 | 5 |
| ESD Protection | ±15 kV HBM | ±15 kV HBM | ±15 kV HBM |
| Signal Standard | RS-232 | RS-232 | RS-232 |
| Charge-Pump Architecture | Integrated RS-232 charge-pump circuitry | Integrated RS-232 charge-pump circuitry | Dual charge-pump circuit |
Ana Farklılayıcılar
- Three transmitters and five receivers in one interface device (karşılaştırma:SN65C3243DBR)
- Single-device consolidation of common RS-232 signals (karşılaştırma:MAX3243EWR)
- Explicit 250 kbps operating-rate specification (karşılaştırma:SN65C3243DBR)
Tasarım Notları
Place the required bypass capacitor and charge-pump components exactly as shown in the Texas Instruments MAX3243 datasheet. Keep the supply and charge-pump nodes compact because long loops can increase radiated noise and reduce transient margin. Connect the exposed connections, where applicable, using the prescribed ground and layout pattern rather than substituting general analog-layout conventions.
Keep RS-232 driver and receiver traces away from switching nodes, high-current return paths, and clocks with fast edges. The MAX3243 generates charge-pump energy internally, so the physical arrangement of its surrounding components is important even though the data rate is only 250 kbps. Preserve the intended signal-ground topology and avoid routing serial traces beneath the charge-pump section.
Do not assume the ±15 kV HBM rating covers lightning, industrial surges, or every connector event. For cables leaving an enclosure, assess whether external TVS devices, surge suppression, or isolation are needed. Also confirm the exact 28-pin SOIC pin mapping and connector assignments; a mechanically similar RS-232 transceiver is not necessarily interchangeable without a full pin and electrical comparison.
Uyumluluk Bilgisi
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified in the referenced manufacturer and distributor pages. AEC-Q100 qualification is not indicated for this commercial interface device.