MAX324CUA+ - Dual NC SPST Analog Switch | Maxim Integrated
MPN: MAX324CUA+ ✓ AktifMAX324CUA+ Genel Bakış
An analog switch is an integrated semiconductor device that routes an electrical signal between terminals under digital control. The MAX324CUA+ belongs to the analog switch category, which sits within interface ICs and broader semiconductor signal-routing systems. Unlike a mechanical relay, it provides compact electronic switching with specified transition timing and low on-resistance. Each internal switch provides a 1:1 connection between its two signal terminals when enabled.
The device contains two independent normally closed SPST switches. Their normally closed behavior means the associated signal path remains connected when the control state is inactive, which distinguishes the MAX324 from the normally open MAX323 family. The 60 ohm on-resistance, 100 ns turn-on time, and 150 ns turn-off time define useful operating characteristics for precision analog routing.
Single-supply operation from 2.7V to 16V allows the MAX324CUA+ to work with low-voltage control systems as well as higher-voltage analog rails. The control interface supports digital command of the two switches while the switched paths handle analog signals. Because it is an analog switch IC rather than a power MOSFET or regulator, its SOA is not applicable and its primary design concerns are signal integrity, control timing, and off-state behavior.
Typical uses include battery-powered instrumentation, sensor signal routing, test-equipment input selection, precision measurement systems, and compact industrial or medical control boards. The 8-pin uMAX package reduces board area, while the dual-switch configuration can control two analog channels from one device. Its 0°C to 70°C commercial temperature rating suits equipment expected to operate within controlled indoor or industrial enclosure environments.
When laying out a board, keep the switched analog traces short and place input and output protection close to the external connectors. Confirm that the inactive-state connection matches the circuit's normally closed requirement and check that control timing does not create an unintended transient during switching. This page also organizes functional comparisons and package-specific replacement information for engineers evaluating an existing MAX324 footprint.
Drop-in alternatifler için MAX324CUA+ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
MAX324EUA+
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MAX324CUA+ Maksimum Değerlendirmeler & Elektriksel Özellikler
| Number of Switches | 2 circuits |
| Switch Configuration | 1:1 |
| Switch Type | Dual SPST |
| Default Contact State | Normally closed |
| On-Resistance | 60 ohm |
| Supply Voltage Range | 2.7V to 16V |
| Turn-On Time | 100 ns |
| Turn-Off Time | 150 ns |
| İşletim Sıcaklığı Aralığı | 0°C to 70°C |
| Paket | 8-pin uMAX |
| Package Type | uMAX/uSOP |
| Montaj Türü | Surface mount |
| RoHS Durumu | Compliant |
| Signal Routing Ratio | 1:1 |
| Pin Sayısı | 8 pins |
| Kategori | Analog switch IC |
| Supply Type | Single supply |
| SAFE Operating Area | Not applicable |
MAX324CUA+ Pin Yapısı
| Pin 1 | S1 — Switch 1 signal terminal |
| Pin 2 | D1 — Switch 1 drain-side signal terminal |
| Pin 3 | V+ — Positive supply input |
| Pin 4 | GND — Ground |
| Pin 5 | D2 — Switch 2 drain-side signal terminal |
| Pin 6 | S2 — Switch 2 signal terminal |
| Pin 7 | IN — Control input |
| Pin 8 | OUT — Control-status output |
Tipik Uygulamalar
MAX324CUA+ için uygundur 6 uygulamas: Battery-Powered Sensor Signal Routing, Precision Test and Measurement Inputs, Industrial Control Signal Selection, Medical Monitoring Signal Switching, Portable Instrument Signal Isolation, Data Acquisition Front-End Switching.
Battery-Powered Sensor Signal Routing
The MAX324CUA+ fits low-voltage sensor-selection circuits because it operates from 2.7V to 16V and provides two 1:1 analog paths. Each normally closed SPST switch can connect an analog sensor line to a measurement channel when the control state requires it. Its 60 ohm on-resistance provides a defined insertion resistance, while 100 ns turn-on and 150 ns turn-off timing support fast control sequencing. The 8-pin uMAX package also keeps the routing stage compact in handheld or portable measurement equipment.
Önerilen
Precision Test and Measurement Inputs
The MAX324CUA+ can route precision test signals by placing its two 1:1 channels between an instrumentation amplifier or converter and selected external inputs. The 60 ohm on-resistance is a useful design parameter when calculating source loading, and the 100 ns turn-on time is suitable for controlled measurement sequences. Because the channels are normally closed, the circuit must account for the connection present before the control input changes, avoiding unintended measurement paths during setup.
Önerilen
Industrial Control Signal Selection
The MAX324CUA+ is suitable for industrial control boards that need to select analog command or feedback signals with a compact dual switch. Its single-supply 2.7V to 16V operating range supports both low-voltage logic and wider analog rails. The two independent channels provide 1:1 routing, while the 60 ohm on-resistance and sub-microsecond switching timing help preserve control integrity. Designers should account for the 0°C to 70°C commercial temperature range when positioning the device within an industrial enclosure.
Önerilen
Medical Monitoring Signal Switching
The MAX324CUA+ can support low-bandwidth signal selection in medical monitoring equipment when a compact, normally closed analog switch is appropriate. Two 1:1 channels permit controlled routing of sensor or conditioning-stage signals, and the 60 ohm on-resistance helps engineers evaluate loading into downstream circuitry. The 100 ns turn-on and 150 ns turn-off times provide defined switching behavior. Medical designs should verify their own safety, isolation, and environmental requirements in addition to the device specifications.
Önerilen
Portable Instrument Signal Isolation
The MAX324CUA+ fits portable instruments that require analog paths to remain connected in a defined inactive state. Its normally closed SPST configuration can isolate or reconnect a signal through control logic, while the 1:1 architecture introduces no intentional gain or scaling. Operation from 2.7V to 16V permits use with compact mixed-voltage systems, and the 8-pin uMAX package limits board area. Layout should keep sensitive analog traces short and separate control routing from the signal nodes.
Önerilen
Data Acquisition Front-End Switching
The MAX324CUA+ can connect selected analog inputs to a data-acquisition front end when one dual switch is sufficient. The 60 ohm on-resistance is the principal loading parameter to include in source-impedance calculations, while the 100 ns and 150 ns transition times establish the basic control timing. Because both channels are normally closed, firmware and hardware sequencing should avoid assuming an open circuit before the switch is actively commanded. The compact uMAX package leaves room for the converter and conditioning circuitry.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MAX324CUA+ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MAX324EUA+ |
|---|---|---|
| Package | 8-pin uMAX | 8-pin uMAX |
| Brand | Maxim Integrated | Maxim Integrated |
| Number of Switches | 2 circuits | 2 circuits |
| Switch Configuration | Dual SPST, 1:1 | Dual SPST, 1:1 |
| Default Contact State | Normally closed | Normally closed |
| On-Resistance | 60 ohm | 60 ohm |
| Supply Voltage Range | 2.7V to 16V | 2.7V to 16V |
| Turn-On Time | 100 ns | 100 ns |
| Turn-Off Time | 150 ns | 150 ns |
Ana Farklılayıcılar
- Defined normally closed signal paths (karşılaştırma:MAX324EUA+)
- Compact dual-channel integration (karşılaştırma:MAX324EUA+)
- Single-supply operating range (karşılaştırma:MAX324EUA+)
Tasarım Notları
Account for the MAX324CUA+ 60 ohm on-resistance when calculating the loading seen by the switched signal source. For high-impedance sensors, compare that resistance with the input impedance of the receiving amplifier and include the source impedance in the complete divider. The normally closed 1:1 paths mean the selected signal may be connected before the control input changes.
Place the MAX324CUA+ close to the switched signal nodes and keep each analog path short and continuous. Route the control input and status output away from sensitive analog traces to reduce coupling into the switched channels. Use the manufacturer pin-description table to confirm terminal orientation, because the package is only 8 pins and an incorrect connection can create a permanent signal path.
Do not treat the MAX324CUA+ as a normally open switch: its two channels are normally closed. Check the required power-off connection and system behavior before using the part for safety isolation, reset routing, or signal selection. Also observe the 2.7V to 16V supply range and the 0°C to 70°C commercial temperature specification during qualification.
Decouple the single supply near the MAX324CUA+ with the capacitance recommended by the manufacturer family documentation and keep the return path continuous to the device ground pin. Because this is an analog switch rather than a voltage regulator, supply bypassing does not replace careful signal-path design; control transitions and shared supply impedance can still affect analog behavior.
Uyumluluk Bilgisi
RoHS compliance is identified for MAX324CUA+. The product is an analog switch IC and is not identified as an AEC-Q100-qualified automotive device. Other compliance attributes require manufacturer confirmation.