MAX394EPP+ - 4-Channel SPDT 35Ω Switch | Analog Devices
MPN: MAX394EPP+ ✓ AktifMAX394EPP+ Genel Bakış
A CMOS analog switch is an electrically controlled pass-device multiplexer that connects one signal terminal to one of two alternatives. The SPDT configuration provides a common terminal and two switched terminals per channel. As part of the semiconductor hierarchy, the MAX394 belongs to the integrated-circuit, interface-IC, analog-switch, and multiplexer families used to route signals between sensors, converters, amplifiers, test equipment, and system controllers.
The MAX394 uses a low-voltage silicon-gate process and is designed to provide low power consumption of 10μW and extremely low charge injection of 10pC. Its ESD protection exceeds 2000V. The four on-resistance channels are matched closely, helping minimize gain and timing variation when the same switch network handles several related signals. The MAX394EPP+ also replaces the MAX333A according to the manufacturer product page.
Dual-supply operation allows the switch to pass signals around ground without requiring a mid-supply reference, while single-supply operation supports systems with a +2.7V to +15V rail. The device provides four independent switching sections rather than a multiplexed shared path, allowing each channel to select its own source. Control inputs determine which terminal is connected to the corresponding common terminal, with actual transition behavior, logic levels, and timing defined by the manufacturer datasheet.
Typical uses include precision test-and-measurement systems, data-acquisition front ends, battery-powered instrumentation, industrial control interfaces, and low-voltage communication equipment. The 20-pin PDIP format also makes the device practical for prototypes, legacy industrial equipment, and hand-assembled test boards where a surface-mount package would complicate inspection or rework.
For reliable operation, confirm the control-logic levels against the supply configuration and observe the absolute maximum ratings before applying signals. Keep connected external circuitry within the specified common-mode range, route high-impedance nodes conservatively, and account for charge injection when changing channel state. The DIP package should also be protected from conductive contamination and cleaned with an appropriate solvent during maintenance.
This page consolidates the manufacturer switch specifications, lifecycle status, package details, engineering guidance, and documented comparison points into a design-oriented reference. It also distinguishes the PDIP MAX394EPP+ from surface-mount MAX394 variants, helping engineers confirm footprint and ordering requirements before beginning a PCB or replacement design.
Drop-in alternatifler için MAX394EPP+ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
MAX394CPP+
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MAX333AEPP+
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MAX394EPP+ Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | Quad SPDT CMOS analog switch |
| Number of Channels | 4 independent channels |
| Switch Configuration | 4 × SPDT |
| On Resistance | 35Ω maximum |
| Bipolar Supply Range | ±2.7V to ±8V |
| Single Supply Range | +2.7V to +15V |
| Charge Injection | 10pC |
| Power Consumption | 10μW |
| ESD Protection | Greater than 2000V |
| On-Resistance Matching Between Channels | Within 2Ω |
| Process Technology | Low-voltage silicon-gate CMOS |
| Paket | 20-pin PDIP |
| Package Pitch | 7.62mm |
| Montaj Türü | Through-hole |
MAX394EPP+ 7.62mm Pin Yapısı Kılavuzu
MAX394EPP+ (7.62mm paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MAX394EPP+.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MAX394EPP+ için uygundur 6 uygulamas: Precision Test and Measurement Systems, Data Acquisition Front Ends, Battery-Powered Instrumentation, Industrial Control Signal Routing, Communication Signal Multiplexing, Legacy Interface Card Replacement.
Precision Test and Measurement Systems
The MAX394EPP+ is well suited to switching low-level analog signals among test instruments, fixtures, amplifiers, and external reference sources. Four independent SPDT channels provide separate routing paths rather than forcing signals through one shared multiplexer, while the 35Ω on resistance helps limit signal attenuation. The 10pC charge injection is also beneficial when the selected path feeds a high-impedance detector, because it reduces the control-transition disturbance injected into that node. Designers should still evaluate the complete signal path for bandwidth, capacitance, leakage, and source-impedance effects.
Önerilen
Data Acquisition Front Ends
The MAX394EPP+ can route sensor or conditioning outputs into a data-acquisition front end by assigning one SPDT channel to each relevant source. Its four independent sections allow multiple signals to be selected without sharing a common multiplexer node, which helps preserve channel consistency and simplify board-level signal organization. The low-voltage operating range supports circuits working near +2.7V through +15V, while 10μW power consumption is beneficial in compact battery-operated systems. The design should account for the switch's off resistance, leakage, capacitance, and input common-mode limits at the intended operating frequency.
Önerilen
Battery-Powered Instrumentation
The MAX394EPP+ fits battery-powered analytical and portable instrumentation because its stated power consumption is only 10μW. The device can operate from a single +2.7V to +15V supply or from bipolar rails, allowing it to support both compact single-rail systems and designs that switch signals centered around ground. Its low 10pC charge injection is advantageous when switching into sensitive measurement nodes. To obtain the intended battery-life benefit, engineers should also account for the leakage and off-state resistance of the complete signal path and confirm that the control-driving circuit consumes no more standby power than required.
Önerilen
Industrial Control Signal Routing
The MAX394EPP+ can route low-voltage control and feedback signals in industrial equipment where four separately selectable paths are needed. Its independent SPDT channels simplify connection of sensor outputs, actuator commands, diagnostic lines, or local test points, while the 35Ω on resistance is suitable for many low-frequency control signals. The through-hole PDIP package also remains convenient for repairable industrial assemblies and manually assembled control boards. Production suitability depends on the exact operating-temperature grade, so designers must verify the ordering table and absolute maximum ratings for the intended enclosure temperature.
Önerilen
Communication Signal Multiplexing
The MAX394EPP+ can select low-voltage communication paths when the design requires four independent SPDT routing decisions. Dual-supply operation from ±2.7V to ±8V is useful for systems that route signals around ground, and the low 35Ω on resistance limits insertion loss in impedance-sensitive paths. The device's low charge injection can help preserve signal integrity during state changes, although actual edge quality also depends on control timing, trace capacitance, and the impedance of the connected network. Engineers should verify bandwidth, off isolation, and channel capacitance before using the switch for high-speed links.
Önerilen
Legacy Interface Card Replacement
The MAX394EPP+ is useful when repairing or upgrading a legacy interface card built around the MAX333A family. The manufacturer identifies MAX394 as the replacement for MAX333A, and both MAX394EPP+ and MAX333AEPP+ use a 20-pin PDIP format, which can simplify mechanical replacement when the pin functions and electrical limits match. A responsible replacement review must compare control-input thresholds, switching timing, charge injection, on resistance, leakage, and absolute maximum ratings. The through-hole package also permits socketed implementation when field replacement and technology refresh are important.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MAX394EPP+ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MAX394CPP+ | MAX333AEPP+ |
|---|---|---|---|
| Package | 20-pin PDIP | 20-pin PDIP - same footprint | 20-pin PDIP - same footprint |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Low-voltage quad SPDT CMOS analog switch | Low-voltage quad SPDT CMOS analog switch | Quad SPDT CMOS analog switch |
| Number of Channels | 4 independent channels | 4 independent channels | 4 channels |
Ana Farklılayıcılar
- Modern MAX394 family replaces the MAX333A (karşılaştırma:MAX333AEPP+)
- Documented low charge injection (karşılaştırma:MAX333AEPP+)
- Four independent SPDT channels (karşılaştırma:MAX394CPP+)
- Low power consumption (karşılaştırma:MAX333AEPP+)
Tasarım Notları
Treat the 35Ω on resistance as part of the complete source-to-load network. For a high-impedance source, the switch resistance adds little attenuation, but for a low-impedance source it can create a divider with downstream resistance. Check off resistance and leakage as well because they determine how accurately a de-selected branch is isolated. Where charge injection matters, include the 10pC device characteristic together with source impedance, load capacitance, and control-edge timing in the settling analysis.
Choose the supply configuration according to the signal range: use +2.7V to +15V for a single-rail system or ±2.7V to ±8V for bipolar routing. Keep control-input levels compatible with the selected configuration and observe the absolute maximum ratings in the manufacturer datasheet. Although the device states 10μW power consumption, total system demand also includes control-driver overhead and leakage through connected analog paths, which can dominate power in a high-impedance battery-powered design.
The 20-pin PDIP package has a 7.62mm pitch and is intended for through-hole assembly. Preserve the manufacturer pin numbering when laying out the board, especially when replacing MAX333AEPP+ with MAX394EPP+. Route each common and switched terminal directly to its intended circuit, avoid long stubs where signal integrity matters, and provide adequate clearance around the through-hole pads. A socket can simplify service replacement if the mechanical layout, pin length, and insertion clearance are validated.
Do not infer drop-in compatibility from the package outline alone. Before substituting MAX394CPP+ or MAX333AEPP+, compare control-input thresholds, switch timing, on and off resistance, charge injection, leakage, common-mode range, and absolute maximum ratings. The MAX394 family is described as replacing MAX333A, but a production release should still document the comparison so that legacy control logic and signal-level constraints remain satisfied.
Uyumluluk Bilgisi
The MAX394 family is an analog interface IC rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, and halogen-free declarations were not identified for this exact ordering code.