MC33074PG - Quad 4.5MHz 44V Op Amp | onsemi
MPN: MC33074PG ✓ AktifMC33074PG Genel Bakış
An operational amplifier is an analog signal-conditioning device that uses high open-loop gain to amplify voltage differences between its inputs. The MC33074 belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchy. It is designed for general-purpose instrumentation, signal conditioning, and feedback-control circuits that can operate from a single supply or split supply. Its common-mode range includes ground potential, which is especially useful in circuits powered from one battery or one low-voltage rail.
The MC33074PG combines 4.5 MHz gain-bandwidth product with a 13 V/µs slew rate, allowing it to process small signals while responding to moderate-amplitude changes without JFET input transistors. The quad configuration places four amplifiers in one 14-pin PDIP package, reducing component count and board space. A 5 mV input offset-voltage figure supports applications requiring repeatable DC amplification and active filtering. The 3.0 V to 44 V supply range accommodates conventional industrial and instrumentation voltage rails.
The bipolar implementation supports operation from split supplies as well as single-supply configurations. This flexibility is useful when a circuit must process signals centered near ground or interface with sensors whose output spans a positive rail. Because the amplifiers share a common package, each channel can perform a different task, such as input amplification, filtering, buffering, error amplification, or output-current-voltage conversion.
Typical uses include low-frequency instrumentation amplifiers, active filters, transducers, sensor-conditioning modules, audio preamplifiers, power-supply control loops, and general industrial control systems. The 4.5 MHz bandwidth is suitable for moderate-frequency precision signal paths, while the 13 V/µs slew rate provides useful transient response for comparator-like and feedback-control tasks. System designers should still verify output swing, output-current capability, input-bias-current effects, and stability for the selected gain and load.
For a stable PCB implementation, use the 14-pin PDIP footprint, provide adequate supply bypassing, and route sensitive input and feedback traces away from high-current outputs. Decoupling capacitors should be placed close to the supply pins. Confirm the common-mode and output-swing limits against the actual circuit rails, especially in single-supply designs where the output may not swing fully to either supply rail.
This product record combines the MC33074 family electrical characteristics, package information, sourcing guidance, verified drop-in options, and practical design notes. It helps engineers identify the correct quad bipolar amplifier, evaluate replacement choices, and plan instrumentation and industrial signal-conditioning layouts around the same 14-pin PDIP footprint.
Drop-in alternatifler için MC33074PG — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
MC33074APG
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MC34074APG
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MC33074PG Maksimum Değerlendirmeler & Elektriksel Özellikler
| Number of Amplifier Circuits | 4 circuits |
| Amplifier Type | General-purpose single-ended operational amplifier |
| Supply Voltage Range | 3.0 V to 44 V |
| Gain-Bandwidth Product | 4.5 MHz |
| Slew Rate | 13 V/µs |
| Input Offset Voltage | 5 mV |
| Paket | 14-PDIP, 0.300 inch (7.62 mm) pitch |
| Technology | Bipolar |
| Supply Configuration | Single supply or split supply |
| Common-Mode Input | Includes ground potential |
| Input Transistor Technology | Bipolar without JFET device technology |
| Operating Temperature Class | Industrial temperature grade |
| Montaj Türü | Through-hole PDIP |
| Packaging | Tube |
| Lead-Free Status | Pb-free |
MC33074PG 14-pdip, 0.300 inch (7.62 mm) pitch Pin Yapısı Kılavuzu
MC33074PG (14-pdip, 0.300 inch (7.62 mm) pitch paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: MC33074PG.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MC33074PG için uygundur 6 uygulamas: Industrial Sensor Signal Conditioning, Active Audio Filters, Power-Supply Feedback Control, Precision Instrumentation Amplification, Transducer and Bridge Signal Interfaces, General-Purpose Control and Feedback Loops.
Industrial Sensor Signal Conditioning
The MC33074PG suits industrial sensor modules that need amplification, filtering, and buffering within one package. Its four channels can handle separate stages of a conditioning chain, while the 3.0 V to 44 V supply range supports conventional instrumentation rails. The 5 mV input offset-voltage specification helps define DC error budget, and the 4.5 MHz bandwidth is more than adequate for many low-frequency pressure, temperature, and position sensor signals. Because the common-mode input range includes ground, the device can operate from a single supply when signal levels remain near the lower rail.
Önerilen
Active Audio Filters
The MC33074PG can implement multi-stage active filters for audio and communication equipment because four amplifiers are integrated in one 14-pin PDIP package. Each stage can provide gain or buffering, helping reduce the number of discrete packages required for a multi-order filter. Its 4.5 MHz gain-bandwidth product provides useful bandwidth for low-frequency audio crossover, equalization, and anti-alias filtering, while the 13 V/µs slew rate supports larger signal transitions. Designers should calculate gain-bandwidth margin and verify output swing against the selected dual- or single-supply configuration.
Önerilen
Power-Supply Feedback Control
The MC33074PG is appropriate for error-amplifier and supervisory-feedback functions in linear or laboratory power-supply designs. Its 3.0 V to 44 V operating range permits operation from conventional analog rails, and the 4.5 MHz gain-bandwidth product can support loop compensation around moderate-bandwidth regulator topologies. Four amplifiers allow independent use for error amplification, current-limit comparison, voltage-reference buffering, and output monitoring. The design must account for common-mode range, output saturation, and stability at the intended closed-loop gain rather than selecting the amplifier from supply rating alone.
Önerilen
Precision Instrumentation Amplification
The MC33074PG can form the central gain and filtering stages of a precision instrumentation module using multiple channels in one package. Its bipolar architecture, 5 mV input offset-voltage figure, 4.5 MHz gain-bandwidth product, and 13 V/µs slew rate are relevant to low-frequency measurement circuits where both DC accuracy and transient response matter. A practical design can use one channel for input amplification, one for active filtering, and two for output buffering or reference conditioning. Check input bias current, common-mode limits, and resistor matching before converting the stated offset-voltage figure into a complete error budget.
Önerilen
Transducer and Bridge Signal Interfaces
The MC33074PG is useful in transducer interfaces that amplify low-level differential or referenced signals and provide active filtering before conversion. Four available amplifiers support input conditioning, gain stages, and output isolation within one 14-pin PDIP footprint. The device's ground-inclusive common-mode range is helpful for sensors operating from a single supply, and its 4.5 MHz bandwidth provides margin for moderate-frequency dynamic response. The 5 mV input offset voltage contributes to the total signal error, so use suitable resistor tolerances and verify input bias-current effects for high-impedance sensor sources.
Önerilen
General-Purpose Control and Feedback Loops
The MC33074PG can serve as a general-purpose quad amplifier in industrial control, actuator, and feedback systems. Separate channels may implement error amplification, comparator-style threshold detection, buffering, and signal conditioning, reducing package count in a dense analog board. Its 13 V/µs slew rate supports faster transitions than a basic precision amplifier, while the 4.5 MHz bandwidth provides useful control-loop dynamics. Verify output-current limits, saturation behavior, and stability with the actual feedback network, especially when driving capacitive loads or operating close to the 3.0 V lower supply limit.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MC33074PG — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MC33074APG | MC34074APG |
|---|---|---|---|
| Package | 14-PDIP (0.300 inch, 7.62 mm pitch) | 14-PDIP (0.300 inch, 7.62 mm pitch) | 14-PDIP (0.300 inch, 7.62 mm pitch) |
| Brand | onsemi | onsemi | onsemi |
| Number of Amplifier Circuits | 4 circuits | 4 circuits | 4 circuits |
| Supply Voltage Range | 3.0 V to 44 V | 3.0 V to 44 V | 3.0 V to 44 V |
| Gain-Bandwidth Product | 4.5 MHz | 4.5 MHz | 4.5 MHz |
| Slew Rate | 13 V/µs | 13 V/µs | 13 V/µs |
| Technology | Bipolar | Bipolar | Bipolar |
| Common-Mode Input Range | Includes ground potential | Includes ground potential | Includes ground potential |
| Supply Configuration | Single supply or split supply | Single supply or split supply | Single supply or split supply |
Ana Farklılayıcılar
- Four independent general-purpose amplifiers in one through-hole package (karşılaştırma:MC33074APG)
- Direct use with low-rail single-supply systems (karşılaştırma:MC34074APG)
- Useful bandwidth and slew-rate combination for general-purpose analog stages (karşılaştırma:MC33074APG)
Tasarım Notları
Place the supply-decoupling capacitors immediately adjacent to the MC33074PG supply and ground pins, and use the shortest practical return path to the supply reference. Keep the 14-pin PDIP footprint compatible with a standard 0.300 inch, or 7.62 mm, pitch hole pattern. Route each amplifier's non-inverting input, inverting input, and feedback components close together to minimize capacitive pickup, while separating output routes from sensitive input traces.
Treat the 4.5 MHz gain-bandwidth product as a closed-loop design constraint rather than a guaranteed usable bandwidth at every gain. Noise gain, feedback-network impedance, load capacitance, and the 13 V/µs slew rate can limit stability or large-signal response. Check the onsemi MC33074 datasheet for the intended gain, supply, load, and bypass configuration, and include probe capacitance at the output when driving test equipment.
Do not assume that the 3.0 V to 44 V supply rating guarantees full output swing at either rail. In single-supply designs, verify the output range against the selected load and signal amplitude, and confirm that the input common-mode range remains valid throughout operation. Also include the 5 mV input offset-voltage figure in the DC error budget and check input bias-current effects for high-impedance sources.
Uyumluluk Bilgisi
The RS product listing identifies MC33074PG as Pb-free. RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals status require confirmation for the exact ordering code.