MC3488ADG - Dual RS-232/RS-423 Driver | onsemi
MPN: MC3488ADG ✗ Son Kullanım ZamanıMC3488ADG Genel Bakış
A line driver is an interface IC that converts logic-level signals into voltage levels suitable for transmission over a wired communications link. Within the hierarchy of interface ICs, a driver sits below multi-channel transceiver and data-converter families and above discrete output-driver circuits. The MC3488ADG supports EIA/TIA-232 and EIA/TIA-423 signaling, allowing legacy serial equipment, industrial control links, and point-to-point data transmission to share a common interface device.
Key features include two driver outputs, a 10.8 V to 13.2 V supply range, and an 8-pin SOIC package for compact surface-mount layouts. The absence of integrated receivers means the device does not provide receive-side signal conditioning, termination, or slew control. Its specified 0 °C to 70 °C operating range makes it most appropriate for commercial-temperature equipment rather than extended industrial or automotive environments.
The MC3488ADG provides separate transmit channels for interfaces requiring independent driver outputs. In an RS-423 point-to-point arrangement, each driver can feed a balanced or appropriately terminated transmission line. In an RS-232 arrangement, the same pair of driver outputs can support unbalanced links when the surrounding system complies with the applicable EIA/TIA-232 interface requirements. The 8-pin SOIC footprint simplifies board assembly but requires care with trace routing, grounding, and protection against cable-borne transients.
Typical uses include legacy serial-port adapters, industrial data acquisition, isolated or protected remote I/O, test equipment, and embedded systems that need a dual RS-232 or RS-423 transmitter stage. The device is particularly suitable where two communication channels are needed without onboard receive channels and where a higher-voltage interface is preferred over a 3.3 V or 5 V logic-level driver.
Designers should verify the source and destination logic thresholds, cable length, grounding method, termination, and connector-level protection before assigning the outputs. Because the MC3488ADG is listed as obsolete, new production designs should first confirm lifecycle status and obtain an approved sourcing plan or select a current equivalent after a complete pin and electrical review.
This product overview consolidates the package, interface, lifecycle, and replacement information engineers need for initial design triage. It also distinguishes verified device facts from application-specific checks that must be completed against the original datasheet and the target transmission standard.
Drop-in alternatifler için MC3488ADG — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller MC3488ADG (aynı form faktörü ve ayağa oturma) — farklı olan Package, Device Type, Supply Voltage Range.
MC3488ADR2G
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MC3488AD
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MC3487DR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →UA9636ACD
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
UA9636AC
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MC3488ADG Özellikler
| Device Type | Dual RS-232/RS-423 line driver |
| Supported Protocols | RS-232, RS-423 |
| Driver Count | 2 drivers |
| Receiver Count | 0 receivers |
| Supply Voltage Range | 10.8 V to 13.2 V |
| İşletim Sıcaklığı Aralığı | 0 °C to 70 °C |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
| Product Status | Obsolete |
| Description | Dual EIA-423/EIA-232D line driver |
MC3488ADG 8-pin soic Pin Yapısı Kılavuzu
MC3488ADG (8-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MC3488ADG.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MC3488ADG için uygundur 6 uygulamas: Legacy RS-232 Port Interface, Point-to-Point RS-423 Data Link, Industrial Data-Acquisition Equipment, Embedded Control Communications, Test and Measurement Front Ends, Protected Remote I/O Links.
Legacy RS-232 Port Interface
The MC3488ADG fits a legacy RS-232 transmitter stage because it combines two driver outputs in an 8-pin SOIC and operates from a 10.8 V to 13.2 V supply. Each channel can convert a logic-level command into an RS-232-compatible line signal when the surrounding design satisfies the applicable interface specifications. Its two-driver arrangement supports equipment with separate transmit paths or dual serial ports without adding two separate driver packages. The zero-receiver count means the receive side must be implemented separately, and the 0 °C to 70 °C rating limits unrestricted use in industrial-temperature enclosures.
Önerilen
Point-to-Point RS-423 Data Link
The MC3488ADG is suitable for a point-to-point RS-423 transmit link because it provides two independent driver channels and a specified 10.8 V to 13.2 V supply range. In this topology, the logic source drives one channel, the transmitted signal travels over the balanced or appropriately configured line, and the receiving equipment supplies its own receiver and termination arrangement. Because the MC3488ADG contains no receivers, it does not handle bus arbitration or return-signal conditioning. The final design must confirm output amplitude, slew rate, data rate, cable length, and ground reference against the complete manufacturer datasheet.
Önerilen
Industrial Data-Acquisition Equipment
The MC3488ADG can provide two serial transmitter channels in compact industrial data-acquisition equipment with commercial-temperature requirements. Its 8-pin SOIC package reduces board area compared with two discrete driver packages, while the 10.8 V to 13.2 V supply range allows use with a regulated interface rail. The device is not a complete transceiver: the receiving instrument, galvanic isolation, surge protection, and termination must be designed separately. Its 0 °C to 70 °C specification should be checked against the enclosure temperature, and the obsolete lifecycle status makes a transition plan important for long-lived instrumentation.
Önerilen
Embedded Control Communications
The MC3488ADG is applicable to embedded controllers that must transmit commands to older RS-232 or RS-423 equipment. The controller can use one driver for status and another for commands, avoiding the need for separate packages when two transmit channels are required. Since the interface voltage supply is higher than common 3.3 V or 5 V logic rails, the design must include an appropriate regulated supply and must not connect the driver outputs directly to a microcontroller unless its levels and tolerances have been verified. The package is an 8-pin SOIC, so decoupling and ground-return routing remain critical to signal integrity.
Önerilen
Test and Measurement Front Ends
The MC3488ADG can serve as a dual transmit stage in test equipment that commands external instruments over older serial interfaces. Its two driver channels support separate trigger and status paths, while the 0-receiver arrangement keeps receive circuitry independent. In an instrument chassis, maintain a controlled ground reference between connected equipment where the interface permits it, isolate the driver output from sensitive analog sections, and add connector-level transient protection for external cables. Before committing to the obsolete MC3488ADG, compare the current interface requirements with an active equivalent because instrument programs often require lifecycle continuity and traceable sourcing.
Önerilen
Protected Remote I/O Links
The MC3488ADG can be used in remote I/O equipment that transmits control or status information over an RS-423 link. The dual-driver structure allows one link to carry commands and another to carry acknowledgments when the remote unit uses separate physical paths, although a conventional full-duplex design may require separate receive circuitry. The device’s 10.8 V to 13.2 V supply range supports a dedicated interface rail, and its SOIC package fits densely populated control boards. For exposed cables, use surge and ESD protection, maintain the specified return path, and validate the receiver termination and cable length before deploying the link.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MC3488ADG — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MC3488ADR2G | MC3488AD | MC3487DR | UA9636ACD |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Ana Farklılayıcılar
- Two transmit drivers without integrated receivers (karşılaştırma:MC3487DR)
- Documented same-footprint onsemi replacement path (karşılaştırma:MC3488ADR2G)
- Established RS-232 and RS-423 compatibility (karşılaştırma:UA9636ACD)
Tasarım Notları
Place the MC3488ADG close to the logic source and the output-routing network, and keep the ground return short and continuous. The 8-pin SOIC device uses a 10.8 V to 13.2 V supply, so provide local decoupling and route the supply and ground pins directly to the relevant planes. Keep sensitive analog and high-speed digital traces away from the driver outputs where practical.
Verify output amplitude, slew rate, logic thresholds, data rate, cable length, and termination directly from the complete manufacturer datasheet. The MC3488ADG has drivers but no receivers, so each receive path needs its own receiver and network. Do not assume that an RS-423 output can drive an RS-232 receiver without checking voltage levels, ground reference, and network impedance.
Do not treat the 8-pin SOIC footprint as proof of pin-for-pin equivalence across all listed alternatives. Compare pin names and positions, unused-channel requirements, supply current, output drive, and temperature grade before substitution. Also treat the obsolete status as a supply-chain issue: request lot traceability and a production continuity plan before committing new builds to the MC3488ADG.
Route each driver output as a short, controlled transmission-line segment away from sensitive circuitry, and place connector-side protection near the external cable interface rather than beside the IC. Confirm the grounding strategy for connected equipment and evaluate common-mode transients in the intended installation. ESD and surge protection components must be selected for the interface voltage and line impedance rather than added by capacitance alone.
Uyumluluk Bilgisi
The device is a commercial-temperature interface IC; automotive qualification is not indicated. No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established.