MCP601T-E/ST - 2.8MHz R-R CMOS Op Amp | Microchip
MPN: MCP601T-E/ST ✓ AktifMCP601T-E/ST Genel Bakış
A CMOS operational amplifier is an active analog signal-conditioning device that uses high-input-impedance differential inputs to amplify the difference between two voltages. The amplifier sits in the signal-chain hierarchy between sensors, transducers, and analog sources on the input side and analog-to-digital converters, filters, control loops, and measurement equipment on the output side. The MCP601 family is designed for general-purpose applications requiring low power, rail-to-rail output operation, and single-supply operation from 2.7 V to 6.0 V.
Key features include a 2.8 MHz gain-bandwidth product, which supports useful closed-loop bandwidth at modest gains, and typical operating current of 230 uA for battery-powered and portable systems. Rail-to-rail output swing allows the output to approach the supply rails under suitable load conditions. The less-than-2 mV input offset specification supports precision-enough DC amplification for sensor interfaces, filtering, buffering, and audio preamplifier stages, while low bias current helps preserve high source impedance.
The MCP601 uses Microchip's advanced CMOS process technology to combine low power consumption with high open-loop gain and rail-to-rail output performance. Its 2.7 V minimum supply voltage supports 3.3 V systems, while the 6.0 V upper limit provides headroom for 5 V rails. Because stability, output swing, noise, and drive capability depend on supply voltage, load current, and feedback configuration, the manufacturer datasheet should be consulted for the operating curves and application limits used in a specific design.
Typical uses include low-power sensor conditioning, current-to-voltage conversion, analog filtering, audio signal amplification, battery-powered instrumentation, and general buffering around microcontrollers. The TSSOP package is appropriate for compact surface-mount designs, while the low operating current is useful when the amplifier must operate continuously from a limited energy source.
When laying out the circuit, place the bypass capacitor close to the supply pin and keep feedback traces short to minimize noise pickup and unwanted coupling. Verify the required common-mode range, output swing, capacitive-load drive, and stability for the selected gain before releasing the layout. This page combines manufacturer specifications, sourcing information, application guidance, and same-footprint alternatives for faster component evaluation.
Drop-in alternatifler için MCP601T-E/ST — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller MCP601T-E/ST (aynı form faktörü ve ayağa oturma) — farklı olan Number of Circuits, Package, Amplifier Type, Supply Voltage Range, Technology.
MCP601T-I/ST
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MCP601-I/ST
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MCP601T-E/ST Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Single general-purpose operational amplifier |
| Supply Voltage Range | 2.7 V to 6.0 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Input Offset Voltage | Less than 2 mV |
| Output Swing | Rail-to-rail |
| Bias Current | Low; exact value not listed |
| Open-Loop Gain | High; exact value not listed |
| Process Technology | Advanced CMOS |
| Number of Circuits | 1 |
| Number of Inputs | 2 |
| Çıkış Sayısı | 1 |
| Paket | 8-pin TSSOP |
| Montaj Türü | Surface mount |
MCP601T-E/ST 8-pin tssop Pin Yapısı Kılavuzu
MCP601T-E/ST (8-pin tssop paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: MCP601T-E/ST.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MCP601T-E/ST için uygundur 6 uygulamas: Low-Power Sensor Signal Conditioning, Battery-Powered Portable Instrumentation, Analog Filtering and Active Gain Stages, Audio Preamplifier and Buffering, Current-to-Voltage Conversion, Industrial Process-Control Loops.
Low-Power Sensor Signal Conditioning
The MCP601T-E/ST is suitable for conditioning the output of a resistive sensor when the circuit operates from a 3.3 V or 5 V rail. Its input bias current is characterized as low, helping preserve the signal from a high-impedance source, while the less-than-2 mV offset specification supports DC amplification at moderate gains. The 230 uA typical operating current also limits the amplifier's contribution to a power budget. Configure it in a non-inverting or differential stage, place the feedback network close to the device, and verify the sensor's source impedance against the input-bias-current and noise requirements before finalizing the gain.
Önerilen
Battery-Powered Portable Instrumentation
The MCP601T-E/ST fits portable measurement systems where a single amplifier must operate from a compact 2.7 V to 6.0 V supply and consume little current. A 230 uA typical operating current helps preserve battery life in continuous-monitoring systems, and the 2.8 MHz gain-bandwidth product supports low-frequency measurement, filtering, and buffering stages. The rail-to-rail output can maximize usable signal swing from a 3.3 V supply. In a portable instrument, confirm the amplifier's quiescent current at the actual supply voltage and evaluate the sensor, reference, and leakage currents before calculating the complete system power budget.
Önerilen
Analog Filtering and Active Gain Stages
The MCP601T-E/ST can implement active low-pass filters or modest gain stages when the signal bandwidth is well below its 2.8 MHz gain-bandwidth product. Use the device in an inverting, non-inverting, or differential topology and select resistor and capacitor values to obtain the required pole and closed-loop gain. The 2.7 V to 6.0 V operating range supports both 3.3 V and 5 V analog sections. Check the closed-loop response and stability for the chosen noise gain, especially if the amplifier drives a capacitive input, an ADC sampling network, or a long PCB trace.
Önerilen
Audio Preamplifier and Buffering
The MCP601T-E/ST can buffer a small audio signal before an analog-to-digital converter or a following gain stage. Its rail-to-rail output helps retain signal amplitude from a single 3.3 V or 5 V supply, while the 2.8 MHz gain-bandwidth product covers many low-bandwidth audio buffering tasks. Use low-noise resistors and capacitors around the amplifier and keep input and feedback routing compact. This device is most appropriate for general-purpose low-level buffering; verify input-referred noise, distortion, output-current capability, and the ADC's input-impedance requirements before using it in a precision audio path.
Önerilen
Current-to-Voltage Conversion
The MCP601T-E/ST can convert a small shunt current into a measurable voltage for a current sensor, protection circuit, or power-monitoring system. Its low bias current reduces the error introduced when sensing a low-value shunt, and the less-than-2 mV offset specification limits the DC error at the input. The 2.8 MHz gain-bandwidth product provides margin for moderate-bandwidth current signals. Select the shunt and feedback resistor to limit power dissipation, confirm that common-mode voltage remains within the allowed input range, and check the amplifier output against the limits of the downstream converter.
Önerilen
Industrial Process-Control Loops
The MCP601T-E/ST can serve as the error amplifier or buffer in a compact 3.3 V or 5 V process-control interface. Its rail-to-rail output supports low-voltage actuator and control-node drive, while the 2.8 MHz gain-bandwidth product is adequate for many slow feedback loops and conditioning stages. The single amplifier and 8-pin TSSOP package simplify compact board layouts. Before using it in a feedback loop, verify stability with the actual sensor capacitance, compensation network, and output loading. Industrial designs should also confirm the required temperature grade and any extended qualification obligations for the deployed environment.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MCP601T-E/ST — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MCP601T-I/ST | MCP601-I/ST |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP |
| Amplifier Type | Single general-purpose CMOS operational amplifier | Single general-purpose CMOS operational amplifier | Single general-purpose CMOS operational amplifier |
| Supply Voltage Range | 2.7 V to 6.0 V | 2.7 V to 6.0 V | 2.7 V to 6.0 V |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA |
| Input Offset Voltage | Less than 2 mV | Less than 2 mV | Less than 2 mV |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Input Bias Current | Low | Low | Low |
| Process Technology | Advanced CMOS | Advanced CMOS | Advanced CMOS |
Ana Farklılayıcılar
- Low-power operation in a compact general-purpose amplifier (karşılaştırma:MCP601T-I/ST)
- Single-supply compatibility for 3.3 V and 5 V systems (karşılaştırma:MCP601-I/ST)
- Same-footprint family sourcing path (karşılaştırma:MCP601T-I/ST)
Tasarım Notları
Route the power pin directly to a decoupling capacitor and place that capacitor close to the device. Keep the feedback-resistor network close to the amplifier inputs and outputs to reduce parasitic coupling. For analog signals entering the PCB from connectors or sensors, use a short trace over a quiet ground reference and separate the route from digital clock and switching-current paths.
Do not assume that rail-to-rail output guarantees the input can operate across the complete supply range. Check the input common-mode range and output-swing curves in the manufacturer datasheet for the selected supply voltage. Also account for the amplifier's offset, bias current, and noise when setting the gain of a high-impedance sensor stage, and verify capacitive-load stability before attaching a long cable or ADC input.
For battery-powered designs, include the MCP601T-E/ST's 230 uA typical operating current in the continuous power budget. Estimated: operation from 3.3 V at 230 uA consumes approximately 0.76 mW of amplifier supply power. The actual figure can differ with supply voltage, output activity, and temperature, so use maximum specifications for a worst-case battery-life estimate.
Uyumluluk Bilgisi
The general-purpose MCP601 amplifier is not identified as an AEC-Q100 automotive device. Specific environmental-compliance declarations should be confirmed for the exact orderable MPN through Microchip's product documentation.