Microchip Technology

MCP6074-E/ST - 1.2MHz Quad Precision Op Amp | Microchip

MPN: MCP6074-E/ST ✓ Aktif
1.8 V to 6 V Vdss 110 µA typical Id 14-pin TSSOP Package
MOQ: 1 |

MCP6074-E/ST Genel Bakış

The Microchip Technology MCP6074-E/ST is a quad precision operational amplifier with a 1.2 MHz gain-bandwidth product, 0.5 V/µs slew rate, and rail-to-rail input and output operation. It operates from 1.8 V to 6 V, consumes 110 µA typical quiescent current per amplifier, and is packaged in a 14-pin TSSOP. The device is designed for low-power precision signal conditioning where accurate offsets and flexible input and output ranges are important.

An operational amplifier is an analog signal-conditioning device that compares its differential input with a feedback-defined reference and amplifies the resulting error. The MCP6074 belongs to the precision operational-amplifier hierarchy within amplifier ICs and analog signal-chain components. Its rail-to-rail inputs allow signals to approach the supply rails, while rail-to-rail outputs improve output-voltage range in low-voltage systems.

The four amplifiers share a maximum input offset voltage of ±150 µV and have unity-gain stability. A 1.2 MHz typical gain-bandwidth product supports low-frequency precision, sensor, filtering, and instrumentation circuits. The 0.5 V/µs slew rate provides useful dynamic performance for pulse and waveform conditioning, although it is not intended for high-speed video or RF applications.

The MCP6074 family is built for low-voltage operation from a single 1.8 V supply through 6 V. Rail-to-rail input and output behavior simplifies signal-headroom calculations when sensors operate near ground or near the positive supply rail. Typical quiescent current of 110 µA per amplifier makes the device suitable for portable and power-constrained equipment when four amplifier channels are needed in one package.

Typical uses include sensor-signal conditioning, low-voltage data acquisition, audio preamplification, active filtering, voltage buffering, and general-purpose analog measurement. Four independent amplifiers in one TSSOP can reduce board area in multi-channel designs, while the common package simplifies assembly when each channel requires similar voltage, bandwidth, and precision characteristics.

When designing around the MCP6074-E/ST, preserve the input common-mode range and output swing under the actual load. Keep feedback loops short, place compensation and bypass capacitors close to their associated pins, and verify stability with the selected capacitor values and load. The TSSOP outline also benefits from adequate copper area for repeatable thermal performance.

This page combines manufacturer specifications, verified distributor listings, same-package replacement guidance, application-oriented design notes, and a parameter comparison for engineers evaluating the MCP6074-E/ST. It also identifies where pin-compatible alternatives preserve the 14-pin TSSOP footprint and where application-specific requirements still need verification before substitution.

Drop-in alternatifler için MCP6074-E/ST — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller MCP6074-E/ST (aynı form faktörü ve ayağa oturma) — farklı olan Amplifier Type, Input Common-Mode Range, Package, Quiescent Current per Amplifier.

Microchip Technology
Amplifier Type: Precision operational amplifier
Input Common-Mode Range: Rail-to-rail
Package: 14-lead TSSOP, 4.40 mm width

MCP6054-E/ST

✅ Yerleştirme
Microchip Technology
📦 14-pin TSSOP
4 channels · Precision operational amplifier · 1.8 V · 385 kHz · ±150 µV · 30 µA · Rail-to-rail · Rail-to-rail

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MCP6054T-E/ST

✅ Yerleştirme
📦 14-pin TSSOP
Same 14-pin TSSOP package and identified functional-equivalent family; temperature-grade and marking differences require comparison against the target specification.

📋 Katalogda Olmayan Referans Alternatifi

MCP6054-E/STVAO

✅ Yerleştirme
📦 14-pin TSSOP
Same 14-pin TSSOP package and identified functional equivalent; automotive ordering code and automotive qualification details must be checked before substitution.

📋 Katalogda Olmayan Referans Alternatifi

MCP6054T-E/STVAO

✅ Yerleştirme
📦 14-pin TSSOP
Same 14-pin TSSOP package and identified functional equivalent; temperature-grade and automotive-marking differences require circuit-level verification.

📋 Katalogda Olmayan Referans Alternatifi

MCP6074-E/STVAO

✅ Yerleştirme
📦 14-pin TSSOP
Same MCP6074 family and 14-pin TSSOP package; automotive ordering code changes the qualification marking, while core functional differences are 0% for the verified 1.2 MHz gain-bandwidth rating.

📋 Katalogda Olmayan Referans Alternatifi

MCP6074-E/ST Maksimum Değerlendirmeler & Elektriksel Özellikler

Number of Amplifier Channels 4 channels
Supply Voltage Range 1.8 V to 6 V
Gain-Bandwidth Product 1.2 MHz typical
Slew Rate 0.5 V/µs
Input Offset Voltage ±150 µV maximum
Quiescent Current per Amplifier 110 µA typical
Input Common-Mode Range Rail-to-rail input
Çıkış Gerilimi Aralığı Rail-to-rail output
Gain Stability Unity-gain stable
Amplifier Type General-purpose precision operational amplifier
Paket 14-pin TSSOP
Montaj Türü Surface mount
Package Length 4.40 mm
Shipping Format Tube
Temperature Grade E temperature grade
Automotive Qualification AEC-Q100

MCP6074-E/ST Pin Yapısı

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Pin 1 OUTA — Operational amplifier A output
Pin 2 V- — Negative supply voltage
Pin 3 INA+ — Non-inverting input for amplifier A
Pin 4 INA- — Inverting input for amplifier A
Pin 5 INB+ — Non-inverting input for amplifier B
Pin 6 INB- — Inverting input for amplifier B
Pin 7 OUTB — Operational amplifier B output
Pin 8 OUTC — Operational amplifier C output
Pin 9 OUTD — Operational amplifier D output
Pin 10 V+ — Positive supply voltage
Pin 11 IND+ — Non-inverting input for amplifier D
Pin 12 IND- — Inverting input for amplifier D
Pin 13 INC+ — Non-inverting input for amplifier C
Pin 14 INC- — Inverting input for amplifier C

Tipik Uygulamalar

MCP6074-E/ST için uygundur 6 uygulamas: Precision Sensor Signal Conditioning, Low-Voltage Data Acquisition, Audio Preamplifier and Buffering, Active Filtering and Signal Conditioning, Industrial Control and Monitoring, Battery-Powered Portable Equipment.

🧩

Precision Sensor Signal Conditioning

The MCP6074-E/ST fits low-voltage sensor front ends requiring accurate amplification close to the supply rails. Its ±150 µV maximum input offset voltage and rail-to-rail inputs help preserve small sensor signals, while the 1.8 V to 6 V operating range supports portable and embedded systems. Each amplifier can condition one sensor channel, with the four-channel package reducing PCB area for multi-axis or redundant sensing. The 1.2 MHz gain-bandwidth product supports moderate-bandwidth signal shaping, although sensor excitation, ADC input range, noise, and filter design determine the final system accuracy.

🖥️

Low-Voltage Data Acquisition

The MCP6074-E/ST is suitable for buffering and scaling inputs entering a low-resolution or mid-resolution data-acquisition system. Rail-to-rail input and output operation gives designers more usable signal range at a 1.8 V minimum supply, and unity-gain stability supports straightforward voltage-follower configurations. Its 110 µA typical quiescent current per amplifier helps limit standby consumption in distributed measurement nodes. Before deployment, verify ADC input range, acquisition time, settling behavior, noise, and whether anti-alias filtering requires a higher-bandwidth amplifier.

🎧

Audio Preamplifier and Buffering

The MCP6074-E/ST can support low-level audio preamplifier, mixer, and output-buffer stages operating from low-voltage rails. The rail-to-rail inputs accommodate microphone or line signals near ground, while rail-to-rail outputs improve swing into the next stage. Its 0.5 V/µs slew rate and 1.2 MHz gain-bandwidth product are suitable for small-signal audio paths that do not require wideband video performance. A quality-conscious design should still evaluate input-noise density, harmonic distortion, channel matching, capacitive loading, and the required output impedance.

🔧

Active Filtering and Signal Conditioning

The MCP6074-E/ST is appropriate for active filters, integrators, and general low-frequency conditioning networks because it is unity-gain stable and supports closed-loop operation above unity gain. A typical gain-bandwidth product of 1.2 MHz leaves a practical frequency range below that value for modest closed-loop gains. Four amplifiers can implement Sallen-Key stages, buffers, or a combination of filtering and gain adjustment in a compact circuit. Component tolerances and the amplifier's gain-bandwidth, output-drive, noise, and stability characteristics must be considered when setting Q and passband response.

🏭

Industrial Control and Monitoring

The MCP6074-E/ST can amplify and buffer control, monitoring, or diagnostic signals in industrial equipment operating from a 1.8 V to 6 V supply. Its low quiescent current supports compact and thermally constrained controller boards, while four amplifiers allow several supervisory channels to share one package. The part is also identified with an automotive-grade ordering option, but the specific ordering code and qualification requirements should be checked for each deployment. Designers should confirm immunity, transient limits, grounding, output drive, and the sensor's full-scale operating range.

📱

Battery-Powered Portable Equipment

The MCP6074-E/ST suits portable and battery-powered instrumentation because it runs from supplies as low as 1.8 V and consumes 110 µA typical quiescent current per amplifier. Rail-to-rail operation can improve utilization of a restricted voltage range, and four channels provide useful integration when monitoring multiple physiological, environmental, or wearable signals. Power-budget analysis must include the amplifier's output-current consumption, external bias networks, sensor current, and regulator efficiency. For wearable designs, also examine noise, electrode or sensor impedance, body-coupled safety, and the required measurement bandwidth.

What are the key specifications of MCP6074-E/ST that engineers should know?
The MCP6074-E/ST is a four-channel, 1.8 V to 6 V precision operational amplifier with rail-to-rail input and output operation. According to the Microchip manufacturer datasheet, it provides a typical gain-bandwidth product of 1.2 MHz, a 0.5 V/µs slew rate, ±150 µV maximum input offset voltage, and 110 µA typical quiescent current per amplifier. It is unity-gain stable and comes in a 14-pin TSSOP. These ratings make it appropriate for low-power sensor conditioning, filtering, buffering, instrumentation, and general analog signal-processing circuits operating close to the supply rails.
Where can I download the MCP6074-E/ST datasheet PDF?
The official MCP6074 datasheet is available through Microchip Technology's product page at https://www.microchip.com/en-us/product/MCP6074. The PDF contains the complete electrical characteristics, pin descriptions, typical performance curves, package drawings, and ordering information for the MCP6074 family. Use the package and ordering tables to confirm that the 14-pin TSSOP, E temperature grade, and ST shipping format correspond to MCP6074-E/ST. The visible product page also provides links to current product resources and related documentation.
Where is the MCP6074-E/ST pinout and what does each pin do?
The MCP6074-E/ST uses a 14-pin TSSOP arrangement with four independent operational amplifiers. Pin 1 is OUTA, pin 2 is V−, pins 3 and 4 are INA+ and INA−, pins 5 and 6 are INB+ and INB−, pin 7 is OUTB, pin 8 is OUTC, pin 9 is OUTD, pin 10 is V+, and pins 11 through 14 are the differential inputs for channels D, C, and B. According to the Microchip manufacturer datasheet, each amplifier has two input pins and one output pin, while the supply pins are shared by all four channels.
Can MCP6074-E/ST operate from a single 1.8 V supply?
Yes, the MCP6074-E/ST can operate from a single supply as low as 1.8 V and supports supplies up to 6 V. According to the Microchip manufacturer datasheet, its rail-to-rail input and output operation allows useful signal operation near the supply limits, making it suitable for low-voltage sensors and portable systems. Designers should still check the common-mode and output-swing graphs for the selected supply voltage, output load, and temperature. Four channels in one package can also reduce board area compared with four separate single-amplifier packages.
What is the gain-bandwidth product of MCP6074-E/ST?
The MCP6074-E/ST has a typical gain-bandwidth product of 1.2 MHz. According to the Microchip manufacturer datasheet, this bandwidth supports unity-gain operation and closed-loop gains commonly used in precision filtering, buffering, and sensor-conditioning circuits. A practical gain-bandwidth product is the approximate maximum closed-loop bandwidth for a given noise gain. The actual response also depends on output load, supply voltage, feedback components, capacitive loading, and the amplifier's gain-versus-frequency behavior, so stability should be verified in the final circuit.
Is MCP6074-E/ST suitable for low-power sensor signal conditioning?
Yes, the MCP6074-E/ST is well suited to low-power sensor signal conditioning because it operates from 1.8 V to 6 V and draws 110 µA typical quiescent current per amplifier. According to the Microchip manufacturer datasheet, its rail-to-rail inputs can accept signals near the supply rails, and ±150 µV maximum offset supports precision measurements. The 1.2 MHz gain-bandwidth product is sufficient for many temperature, pressure, position, and biochemical sensor front ends. Sensor-specific accuracy also depends on excitation, reference noise, ADC resolution, filtering, calibration, and overall system error.
What can replace MCP6074-E/ST on the same 14-pin TSSOP footprint?
The MCP6054-E/ST is a same-brand, 14-pin TSSOP alternative identified as a functional equivalent to the MCP6074-E/ST. The Microchip cross-reference data also identifies MCP6054T-E/ST, MCP6054-E/STVAO, and MCP6054T-E/STVAO as related functional equivalents, while MCP6074-E/STVAO is an automotive-marked variant of the MCP6074. Before replacing the MCP6074, verify offset voltage, gain-bandwidth product, slew rate, input bias current, noise, common-mode range, output swing, shutdown behavior, and temperature grade against the application. The package match alone does not establish functional equivalence.
Is MCP6074-E/ST the same as MCP6054-E/ST?
No, the MCP6074-E/ST and MCP6054-E/ST are related Microchip precision amplifiers but should not be treated as electrically identical without review. Both are associated with low-voltage, low-power precision amplifier families and use the 14-pin TSSOP format, which makes the MCP6054-E/ST a candidate for board-level substitution. According to Microchip's comparison information, the MCP6074-E/ST has a typical gain-bandwidth product of 1.2 MHz. Check the MCP6054's corresponding electrical ratings and pin functions in its manufacturer datasheet before approving it as a drop-in replacement.
MCP6074-E/ST vs MCP6054-E/ST: which is better for precision filtering?
The MCP6074-E/ST is preferable when its 1.2 MHz typical gain-bandwidth product and ±150 µV maximum input offset voltage satisfy the filter's accuracy and bandwidth requirements. The MCP6054-E/ST is the practical same-package candidate to evaluate when its input offset, gain-bandwidth product, noise, and output-drive specifications meet the design. According to the Microchip comparison information, the MCP6074-E/ST is unity-gain stable and has 0.5 V/µs slew rate. For a precision filter, compare actual passband gain error, phase margin, component tolerances, and output-load behavior rather than selecting solely by package.
When should I choose MCP6074-E/ST over MCP6054-E/ST?
Choose the MCP6074-E/ST when the design benefits directly from its documented 1.2 MHz typical gain-bandwidth product, ±150 µV maximum input offset voltage, rail-to-rail input and output operation, and 110 µA typical quiescent current per amplifier. According to the Microchip manufacturer datasheet, it is unity-gain stable and supports operation from 1.8 V to 6 V. Select the MCP6054-E/ST only after confirming that its gain, bandwidth, offset, noise, bias current, supply range, and stability meet the same requirements. Both are 14-pin TSSOP devices, so the electrical comparison remains decisive.
Is MCP6074-E/ST suitable for audio preamplifier applications?
The MCP6074-E/ST can be used for low-level audio preamplification when the circuit operates within its bandwidth, output-swing, noise, and supply limits. According to the Microchip manufacturer datasheet, the device provides rail-to-rail input and output operation, a 1.2 MHz typical gain-bandwidth product, and a 0.5 V/µs slew rate. These characteristics suit small-signal microphone, line, and headphone-buffer stages operating from low-voltage supplies. For high-fidelity systems, compare input-voltage noise, distortion at the required output level, channel matching, and the load impedance with the selected microphone and output architecture.
How should decoupling and layout be handled for MCP6074-E/ST?
Place the supply bypass capacitor directly between V+ and V− pins, and keep the feedback and input traces short to reduce parasitic coupling and instability risk. According to the Microchip manufacturer datasheet, the MCP6074 is unity-gain stable, but stable operation still depends on the selected feedback network and load. Use solid ground-plane continuity beneath the amplifier, avoid routing high-current return paths through the analog area, and keep sensitive input nodes away from switching nodes. Check the datasheet's recommended capacitor values and stability curves against the actual output load.
How much power does MCP6074-E/ST consume?
The MCP6074-E/ST draws 110 µA typical quiescent current per amplifier according to the Microchip manufacturer datasheet. With four amplifiers, the typical quiescent current is approximately 440 µA under the stated conditions. Estimated: this calculation uses four channels at 110 µA each; actual supply consumption also depends on supply voltage, input voltages, output current, slew activity, and the external load. The device is therefore suited to low-voltage, low-power systems when output drive and dynamic performance remain within the quad amplifier's capabilities.
Where can I buy MCP6074-E/ST and check its current availability?
Use the Request a Quote form on this page to ask about MCP6074-E/ST pricing, current stock, minimum order quantity, and lead time. The form is the fastest way to obtain an order-ready response for the exact 14-pin TSSOP ordering code. Inventory and lead time can change by region, quantity, and shipment method, so they should be confirmed at the time of quotation. Specify MCP6074-E/ST rather than MCP6074-E/SL when the PCB requires the 14-pin TSSOP package, and identify tube or reel preferences separately if either delivery format is acceptable.
What is the lead time for MCP6074-E/ST?
The current lead time for MCP6074-E/ST should be confirmed through the Request a Quote form on this page. Lead time depends on the ordered quantity, package shipping format, destination, and current manufacturer allocation. Request the exact MPN and required quantity so the commercial response reflects the 14-pin TSSOP configuration. For production planning, obtain a delivery schedule before committing the BOM. Do not substitute MCP6074-E/SL without PCB review, because that ordering code is associated with a 14-pin SOIC package rather than the target TSSOP.
What is the price of MCP6074-E/ST?
The current price of MCP6074-E/ST is obtained through the Request a Quote form on this page. Submit the exact MPN, required quantity, and preferred shipping format for a purchase quotation. Pricing depends on order quantity, supply position, and delivery terms, and a quote avoids publishing a value that may already be outdated. Request confirmation that the supplied device is MCP6074-E/ST in the 14-pin TSSOP package. Also request lot-traceability and date-code information when required for production inventory control.

Mühendislik referans verileri: MCP6074-E/ST — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose MCP6074-E/ST for compact low-voltage precision designs that need four unity-gain-stable amplifiers with rail-to-rail input and output, a 1.2 MHz typical gain-bandwidth product, and 110 µA typical quiescent current per channel. It is a strong fit for sensor conditioning, data acquisition, low-level audio, buffering, and active filtering. MCP6054-E/ST is the closest same-package candidate to evaluate when its offset, noise, bias current, bandwidth, and drive ratings meet the design; confirm all electrical differences rather than relying on the shared TSSOP footprint. Use MCP6074-E/STVAO when the program requires the automotive-marked ordering option and applicable qualification documentation. MCP6054T-E/ST, MCP6054-E/STVAO, and MCP6054T-E/STVAO offer further same-package ordering-code paths but require temperature-grade, qualification, and electrical review. Do not use MCP6074-E/SL as a board-level substitute without redesigning the footprint.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün MCP6054-E/ST MCP6054T-E/ST MCP6054-E/STVAO MCP6054T-E/STVAO MCP6074-E/STVAO
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP 14-pin TSSOP

Ana Farklılayıcılar

  • Four precision amplifiers integrated in one TSSOP (karşılaştırma:MCP6054-E/ST)
  • Defined low-voltage performance (karşılaştırma:MCP6054-E/ST)
  • Rail-to-rail signal range (karşılaştırma:MCP6054-E/ST)
  • Automotive-marked same-package option (karşılaştırma:MCP6054-E/ST)

Tasarım Notları

Place the supply bypass capacitor directly between the V+ and V− pins, with the shortest possible connection to the package. Keep amplifier input and feedback traces away from switching nodes and high-current return paths. A continuous ground plane under the TSSOP improves return-path consistency, while short feedback loops reduce parasitic capacitance that can affect stability. Orient the decoupling capacitor so its connection to the ground reference does not traverse sensitive input nodes.

Verify stability with the final load and feedback values rather than assuming unity-gain stability guarantees every configuration. Capacitive loading can interact with the amplifier output stage and feedback network to produce peaking or oscillation. If the source impedance is high, account for input bias-current error and parasitic capacitance. For precision measurements, use short routed inputs, guarded or driven reference nodes, and an RC anti-alias network selected against the required signal bandwidth.

Estimated: at a 3.3 V supply, the amplifier bias current contributes approximately 1.45 mW per amplifier and 5.80 mW for all four channels, calculated from 3.3 V × 110 µA. Actual consumption rises with output-current demand and dynamic activity, so include the external load and support circuitry in the power budget. The low-voltage range does not imply the output can drive an unrestricted load; check output-current and thermal limits for the selected rail and package.

Do not substitute MCP6074-E/SL for MCP6074-E/ST without changing or reviewing the PCB because MCP6074-E/SL uses a 14-pin SOIC package. Also verify that MCP6074-E/STVAO and other VAO ordering codes meet the intended automotive qualification, traceability, and temperature requirements. For every drop-in candidate, compare input bias current, output drive, noise, common-mode range, output swing, and stability rather than relying on package dimensions alone.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The automotive MCP6074 ordering option is associated with AEC-Q100. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not explicitly stated and remain unknown.

İlgili Aramalar

MCP6074-E/ST datasheet MCP6074-E/ST pinout MCP6074-E/ST datasheet pdf MCP6074-E/ST equivalent MCP6074-E/ST replacement MCP6074-E/ST cross reference MCP6074-E/ST vs MCP6054-E/ST MCP6074-E/ST TSSOP pinout MCP6074-E/ST price MCP6074-E/ST stock Microchip MCP6074-E/ST MCP6074 1.2MHz quad op amp MCP6074-E/ST sensor signal conditioning MCP6074-E/ST low voltage amplifier

İlgili Bileşenler ve Terimler

Microchip Technology MCP6074-E/ST MCP6074 MCP6054-E/ST MCP6054T-E/ST MCP6054-E/STVAO MCP6054T-E/STVAO MCP6074-E/STVAO operational amplifier precision operational amplifier quad amplifier analog signal conditioner rail-to-rail input rail-to-rail output gain-bandwidth product input offset voltage slew rate quiescent current unity-gain stable 14-pin TSSOP TSSOP package family surface-mount package sensor signal conditioning data acquisition AEC-Q100
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle