MCP6074-E/ST - 1.2MHz Quad Precision Op Amp | Microchip
部品番号: MCP6074-E/ST ✓ 生産中MCP6074-E/ST 概要
An operational amplifier is an analog signal-conditioning device that compares its differential input with a feedback-defined reference and amplifies the resulting error. The MCP6074 belongs to the precision operational-amplifier hierarchy within amplifier ICs and analog signal-chain components. Its rail-to-rail inputs allow signals to approach the supply rails, while rail-to-rail outputs improve output-voltage range in low-voltage systems.
The four amplifiers share a maximum input offset voltage of ±150 µV and have unity-gain stability. A 1.2 MHz typical gain-bandwidth product supports low-frequency precision, sensor, filtering, and instrumentation circuits. The 0.5 V/µs slew rate provides useful dynamic performance for pulse and waveform conditioning, although it is not intended for high-speed video or RF applications.
The MCP6074 family is built for low-voltage operation from a single 1.8 V supply through 6 V. Rail-to-rail input and output behavior simplifies signal-headroom calculations when sensors operate near ground or near the positive supply rail. Typical quiescent current of 110 µA per amplifier makes the device suitable for portable and power-constrained equipment when four amplifier channels are needed in one package.
Typical uses include sensor-signal conditioning, low-voltage data acquisition, audio preamplification, active filtering, voltage buffering, and general-purpose analog measurement. Four independent amplifiers in one TSSOP can reduce board area in multi-channel designs, while the common package simplifies assembly when each channel requires similar voltage, bandwidth, and precision characteristics.
When designing around the MCP6074-E/ST, preserve the input common-mode range and output swing under the actual load. Keep feedback loops short, place compensation and bypass capacitors close to their associated pins, and verify stability with the selected capacitor values and load. The TSSOP outline also benefits from adequate copper area for repeatable thermal performance.
This page combines manufacturer specifications, verified distributor listings, same-package replacement guidance, application-oriented design notes, and a parameter comparison for engineers evaluating the MCP6074-E/ST. It also identifies where pin-compatible alternatives preserve the 14-pin TSSOP footprint and where application-specific requirements still need verification before substitution.
ドロップイン代替品: MCP6074-E/ST — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MCP6074-E/ST (同一形状・フットプリント) — 相違点: Amplifier Type, Input Common-Mode Range, Package, Quiescent Current per Amplifier.
MCP6054-E/ST
✅ ドロップイン価格はお問い合わせください
データシートを見る →MCP6054T-E/ST
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MCP6054-E/STVAO
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MCP6054T-E/STVAO
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MCP6074-E/STVAO
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MCP6074-E/ST 最大定格&電気的特性
| Number of Amplifier Channels | 4 channels |
| Supply Voltage Range | 1.8 V to 6 V |
| Gain-Bandwidth Product | 1.2 MHz typical |
| Slew Rate | 0.5 V/µs |
| Input Offset Voltage | ±150 µV maximum |
| Quiescent Current per Amplifier | 110 µA typical |
| Input Common-Mode Range | Rail-to-rail input |
| 出力電圧範囲 | Rail-to-rail output |
| Gain Stability | Unity-gain stable |
| Amplifier Type | General-purpose precision operational amplifier |
| パッケージ | 14-pin TSSOP |
| 実装タイプ | Surface mount |
| Package Length | 4.40 mm |
| Shipping Format | Tube |
| Temperature Grade | E temperature grade |
| Automotive Qualification | AEC-Q100 |
MCP6074-E/ST ピン構成
| ピン 1 | OUTA — Operational amplifier A output |
| ピン 2 | V- — Negative supply voltage |
| ピン 3 | INA+ — Non-inverting input for amplifier A |
| ピン 4 | INA- — Inverting input for amplifier A |
| ピン 5 | INB+ — Non-inverting input for amplifier B |
| ピン 6 | INB- — Inverting input for amplifier B |
| ピン 7 | OUTB — Operational amplifier B output |
| ピン 8 | OUTC — Operational amplifier C output |
| ピン 9 | OUTD — Operational amplifier D output |
| ピン 10 | V+ — Positive supply voltage |
| ピン 11 | IND+ — Non-inverting input for amplifier D |
| ピン 12 | IND- — Inverting input for amplifier D |
| ピン 13 | INC+ — Non-inverting input for amplifier C |
| ピン 14 | INC- — Inverting input for amplifier C |
主な用途
MCP6074-E/ST の用途: 6 件s: Precision Sensor Signal Conditioning, Low-Voltage Data Acquisition, Audio Preamplifier and Buffering, Active Filtering and Signal Conditioning, Industrial Control and Monitoring, Battery-Powered Portable Equipment.
Precision Sensor Signal Conditioning
The MCP6074-E/ST fits low-voltage sensor front ends requiring accurate amplification close to the supply rails. Its ±150 µV maximum input offset voltage and rail-to-rail inputs help preserve small sensor signals, while the 1.8 V to 6 V operating range supports portable and embedded systems. Each amplifier can condition one sensor channel, with the four-channel package reducing PCB area for multi-axis or redundant sensing. The 1.2 MHz gain-bandwidth product supports moderate-bandwidth signal shaping, although sensor excitation, ADC input range, noise, and filter design determine the final system accuracy.
おすすめ
Low-Voltage Data Acquisition
The MCP6074-E/ST is suitable for buffering and scaling inputs entering a low-resolution or mid-resolution data-acquisition system. Rail-to-rail input and output operation gives designers more usable signal range at a 1.8 V minimum supply, and unity-gain stability supports straightforward voltage-follower configurations. Its 110 µA typical quiescent current per amplifier helps limit standby consumption in distributed measurement nodes. Before deployment, verify ADC input range, acquisition time, settling behavior, noise, and whether anti-alias filtering requires a higher-bandwidth amplifier.
おすすめ
Audio Preamplifier and Buffering
The MCP6074-E/ST can support low-level audio preamplifier, mixer, and output-buffer stages operating from low-voltage rails. The rail-to-rail inputs accommodate microphone or line signals near ground, while rail-to-rail outputs improve swing into the next stage. Its 0.5 V/µs slew rate and 1.2 MHz gain-bandwidth product are suitable for small-signal audio paths that do not require wideband video performance. A quality-conscious design should still evaluate input-noise density, harmonic distortion, channel matching, capacitive loading, and the required output impedance.
おすすめ
Active Filtering and Signal Conditioning
The MCP6074-E/ST is appropriate for active filters, integrators, and general low-frequency conditioning networks because it is unity-gain stable and supports closed-loop operation above unity gain. A typical gain-bandwidth product of 1.2 MHz leaves a practical frequency range below that value for modest closed-loop gains. Four amplifiers can implement Sallen-Key stages, buffers, or a combination of filtering and gain adjustment in a compact circuit. Component tolerances and the amplifier's gain-bandwidth, output-drive, noise, and stability characteristics must be considered when setting Q and passband response.
おすすめ
Industrial Control and Monitoring
The MCP6074-E/ST can amplify and buffer control, monitoring, or diagnostic signals in industrial equipment operating from a 1.8 V to 6 V supply. Its low quiescent current supports compact and thermally constrained controller boards, while four amplifiers allow several supervisory channels to share one package. The part is also identified with an automotive-grade ordering option, but the specific ordering code and qualification requirements should be checked for each deployment. Designers should confirm immunity, transient limits, grounding, output drive, and the sensor's full-scale operating range.
おすすめ
Battery-Powered Portable Equipment
The MCP6074-E/ST suits portable and battery-powered instrumentation because it runs from supplies as low as 1.8 V and consumes 110 µA typical quiescent current per amplifier. Rail-to-rail operation can improve utilization of a restricted voltage range, and four channels provide useful integration when monitoring multiple physiological, environmental, or wearable signals. Power-budget analysis must include the amplifier's output-current consumption, external bias networks, sensor current, and regulator efficiency. For wearable designs, also examine noise, electrode or sensor impedance, body-coupled safety, and the required measurement bandwidth.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MCP6074-E/ST — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MCP6054-E/ST | MCP6054T-E/ST | MCP6054-E/STVAO | MCP6054T-E/STVAO | MCP6074-E/STVAO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
主な差別化要因
- Four precision amplifiers integrated in one TSSOP (vs MCP6054-E/ST)
- Defined low-voltage performance (vs MCP6054-E/ST)
- Rail-to-rail signal range (vs MCP6054-E/ST)
- Automotive-marked same-package option (vs MCP6054-E/ST)
設計ノート
Place the supply bypass capacitor directly between the V+ and V− pins, with the shortest possible connection to the package. Keep amplifier input and feedback traces away from switching nodes and high-current return paths. A continuous ground plane under the TSSOP improves return-path consistency, while short feedback loops reduce parasitic capacitance that can affect stability. Orient the decoupling capacitor so its connection to the ground reference does not traverse sensitive input nodes.
Verify stability with the final load and feedback values rather than assuming unity-gain stability guarantees every configuration. Capacitive loading can interact with the amplifier output stage and feedback network to produce peaking or oscillation. If the source impedance is high, account for input bias-current error and parasitic capacitance. For precision measurements, use short routed inputs, guarded or driven reference nodes, and an RC anti-alias network selected against the required signal bandwidth.
Estimated: at a 3.3 V supply, the amplifier bias current contributes approximately 1.45 mW per amplifier and 5.80 mW for all four channels, calculated from 3.3 V × 110 µA. Actual consumption rises with output-current demand and dynamic activity, so include the external load and support circuitry in the power budget. The low-voltage range does not imply the output can drive an unrestricted load; check output-current and thermal limits for the selected rail and package.
Do not substitute MCP6074-E/SL for MCP6074-E/ST without changing or reviewing the PCB because MCP6074-E/SL uses a 14-pin SOIC package. Also verify that MCP6074-E/STVAO and other VAO ordering codes meet the intended automotive qualification, traceability, and temperature requirements. For every drop-in candidate, compare input bias current, output drive, noise, common-mode range, output swing, and stability rather than relying on package dimensions alone.
コンプライアンス情報
The automotive MCP6074 ordering option is associated with AEC-Q100. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not explicitly stated and remain unknown.