Microchip Technology

MCP607T-I/SN - Dual 155 kHz Micropower Op Amp | Microchip

MPN: MCP607T-I/SN ✓ Aktif
2.5 V to 6.0 V Vdss 18.7 uA Id 8-pin SOIC, 3.9 mm width Package
MOQ: 1 |

MCP607T-I/SN Genel Bakış

The Microchip Technology MCP607T-I/SN is a dual micropower CMOS operational amplifier with a 155 kHz gain-bandwidth product, 18.7 uA typical operating current, and less than 250 uV offset voltage, housed in an 8-pin SOIC package. It operates from a single 2.5 V to 6.0 V supply and provides rail-to-rail output swing for low-voltage signal-chain designs.

An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, or compare low-level analog signals. The MCP607 belongs to the operational-amplifier hierarchy within analog ICs, where its CMOS implementation emphasizes low bias current, low power consumption, rail-to-rail output operation, and single-supply usability.

The MCP607 combines two amplifier channels in one package. Key characteristics include a 155 kHz gain-bandwidth product, 18.7 uA typical operating current, less than 250 uV offset voltage, low input bias current, and rail-to-rail output swing. Its micropower operation is particularly useful in portable instruments, battery-powered sensors, and low-voltage industrial measurement systems where continuous analog amplification must remain energy efficient.

Microchip's CMOS process technology supports the device's low-power and low-bias-current characteristics. The amplifiers are designed for single-supply operation, which simplifies signal-chain design when the input and output signals remain within the 2.5 V to 6.0 V supply range. Exact input common-mode range, noise density, slew rate, and open-loop gain values require confirmation in the manufacturer datasheet.

Typical uses include sensor-signal conditioning, low-voltage transducer amplification, audio preamplification, portable measurement equipment, and general-purpose analog buffering. The dual-channel configuration also supports independent signal paths, such as filtering two sensor outputs or implementing an instrumentation front end with matched amplifier stages.

Designers should verify the actual input common-mode range before accepting signals near the supply rails, even though the output can swing rail to rail. Stable operation also depends on the selected gain, capacitive loading, output isolation, and the bypass-capacitor configuration recommended by the manufacturer.

This product page consolidates the device's key operating characteristics, sourcing information, available drop-in alternatives, and application-focused design guidance. It is intended to help engineers identify the correct Microchip ordering code, assess the amplifier for a low-voltage analog design, and plan PCB implementation before completing detailed circuit validation.

Drop-in alternatifler için MCP607T-I/SN — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller MCP607T-I/SN (aynı form faktörü ve ayağa oturma) — farklı olan Amplifier Type, Package, Number of Channels.

Microchip Technology
Amplifier Type: Dual voltage-feedback operational amplifier
Package: 8-pin SOIC
Number of Channels: 2 channels
Microchip Technology
Amplifier Type: CMOS Operational Amplifier
Package: 8-TSSOP (ST)
Number of Channels: 2 (Dual)

MCP607-I/SN

✅ Yerleştirme
Microchip Technology
📦 8-pin SOIC
Dual voltage-feedback operational amplifier · 2 channels · 2.5 V to 6.0 V · 18.7 uA · 155 kHz · <250 uV

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

MCP607T-I/SN Maksimum Değerlendirmeler & Elektriksel Özellikler

Amplifier Type Dual general-purpose operational amplifier
Channel Count 2 channels
Supply Voltage Range 2.5 V to 6.0 V
Typical Operating Current 18.7 uA
Listed Operating Current 25 uA
Gain-Bandwidth Product 155 kHz
Offset Voltage Less than 250 uV
Input Bias Current 80 pA maximum at +85 C
Output Swing Rail-to-rail
Technology CMOS
Temperature Grade Industrial
Paket 8-pin SOIC, 3.9 mm width
Montaj Türü Surface mount

MCP607T-I/SN Pin Yapısı

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 OUTA — Amplifier A output
Pin 2 IN A- — Amplifier A inverting input
Pin 3 IN A+ — Amplifier A non-inverting input
Pin 4 V- — Negative supply or ground connection
Pin 5 IN B+ — Amplifier B non-inverting input
Pin 6 IN B- — Amplifier B inverting input
Pin 7 OUTB — Amplifier B output
Pin 8 V+ — Positive supply connection

Tipik Uygulamalar

MCP607T-I/SN için uygundur 6 uygulamas: Battery-Powered Sensor Signal Conditioning, Portable Medical Measurement Instruments, Low-Voltage Audio Preamplification, Industrial Data Acquisition, Portable Test and Measurement, Low-Power IoT Sensor Nodes.

🧩

Battery-Powered Sensor Signal Conditioning

The MCP607T-I/SN fits low-energy sensor front ends because its 18.7 uA typical operating current limits continuous amplifier bias consumption while each channel handles a separate signal. Place the dual amplifier around resistive sensors, bridge outputs, or low-level transducers operating from a 2.5 V to 6.0 V source. Its less-than-250-uV offset characteristic helps preserve small differential signals, while rail-to-rail output swing increases usable signal range. Confirm the input common-mode limits against the sensor output and use local bypass capacitance to maintain a low-impedance supply reference.

💊

Portable Medical Measurement Instruments

The MCP607T-I/SN is appropriate for portable biomedical instrumentation where two low-level channels can be amplified from a compact, low-voltage supply. Its 155 kHz gain-bandwidth product is suitable for low-bandwidth pressure, temperature, or biochemical sensor signals rather than wideband waveform work, and its 18.7 uA typical operating current supports longer battery life. The dual SOIC package reduces board area, while less-than-250-uV offset supports precision-oriented signal paths. Validate patient-safety isolation, input protection, and applicable medical-device requirements separately from the op amp selection.

🎧

Low-Voltage Audio Preamplification

The MCP607T-I/SN can serve as a dual low-voltage audio preamplifier for microphone or line-level signals when bandwidth requirements remain modest. Its 155 kHz gain-bandwidth product provides more bandwidth than a strictly audio-focused low-power amplifier, while the 18.7 uA typical operating current limits power use in portable listening equipment. Rail-to-rail output swing allows the amplifier to approach the supply limits, although gain must be limited to prevent instability. Check input-noise and slew-rate figures in the manufacturer datasheet, and keep feedback routing short to avoid added oscillation margin problems.

🏭

Industrial Data Acquisition

The MCP607T-I/SN is useful in compact industrial data-acquisition modules that condition two low-level analog channels from sensors, resistive dividers, or external transducer modules. Its industrial ordering designation supports use in industrial environments, and the 155 kHz gain-bandwidth product is appropriate for slow process signals requiring moderate amplification. The 18.7 uA typical operating current is valuable when several amplifier channels share a limited power budget. Provide local supply decoupling, maintain common ground paths between the sensor and amplifier, and verify the input common-mode range across industrial supply tolerances.

🔧

Portable Test and Measurement

The MCP607T-I/SN supports compact handheld test equipment by amplifying two low-level inputs without the current draw of a higher-bandwidth dual op amp. Its 18.7 uA typical operating current complements a battery-powered architecture, and the 2.5 V minimum supply permits operation from appropriately regulated low-voltage sources. The less-than-250-uV offset characteristic is useful for excitation, sensing, and reference-related paths, while the 155 kHz gain-bandwidth product handles moderate-frequency instrumentation signals. Account for probe capacitance and sensor drive requirements when selecting the external feedback network.

📱

Low-Power IoT Sensor Nodes

The MCP607T-I/SN fits IoT sensor nodes that require continuous analog amplification near a sensor rather than transmitting an unconditioned signal directly to a digital converter. Two channels can amplify separate environmental or motion-related inputs, while 18.7 uA typical operating current limits the amplifier contribution to node energy use. Its rail-to-rail output can improve utilization of a 2.5 V to 6.0 V rail, and the less-than-250-uV offset supports small-signal conditioning. Pair it with careful input protection and verify common-mode limits before the sensor output can approach either supply rail.

Önerilen Ürünler Özeti

MCP606 Related single-channel CMOS op amp Kullanıldığı Yer: Battery-Powered Sensor Signal Conditioning, Portable Medical Measurement Instruments, Low-Voltage Audio Preamplification, Industrial Data Acquisition, Portable Test and Measurement, Low-Power IoT Sensor Nodes MCP608 Related single-channel CMOS op amp Kullanıldığı Yer: Battery-Powered Sensor Signal Conditioning, Low-Voltage Audio Preamplification, Industrial Data Acquisition, Portable Test and Measurement MCP609 Related single-channel CMOS op amp Kullanıldığı Yer: Battery-Powered Sensor Signal Conditioning, Portable Medical Measurement Instruments, Industrial Data Acquisition, Low-Power IoT Sensor Nodes
What are the key specifications of MCP607T-I/SN that engineers should know?
The MCP607T-I/SN is a dual micropower CMOS operational amplifier with a 155 kHz gain-bandwidth product, 18.7 uA typical operating current, and less than 250 uV offset voltage. According to the Microchip MCP607 product page, the device operates from a 2.5 V to 6.0 V single supply and provides rail-to-rail output swing. It is packaged in an 8-pin SOIC and is intended for low-voltage, low-power analog signal conditioning.
What is the supply voltage range of MCP607T-I/SN?
The MCP607T-I/SN operates from 2.5 V to 6.0 V. The Microchip MCP607 datasheet identifies the device as a 2.5 V to 6.0 V micropower CMOS op amp. This range supports 3.3 V and 5 V systems, but the exact input common-mode limits should be checked in the manufacturer datasheet before operating signals close to either supply rail.
How much current does MCP607T-I/SN consume?
The MCP607T-I/SN has a typical operating current of 18.7 uA according to the Microchip MCP607 product page, while distributor product descriptions identify it as a 25 uA dual op amp. The two figures describe different listing conventions or operating points, so circuit-level power budgets should use the value and test conditions stated in the manufacturer datasheet for the selected production variant.
Where can I download the MCP607T-I/SN datasheet PDF?
The official MCP607T-I/SN datasheet is available through the Microchip MCP607 product page and the Microchip document links for the MCP607 family. The manufacturer page identifies the device as a 2.5 V to 6.0 V micropower CMOS op amp. Use the Microchip document for authoritative pin descriptions, electrical characteristics, test conditions, package dimensions, and ordering information.
Where can I find the MCP607T-I/SN pinout?
The MCP607T-I/SN uses a standard dual-op-amp 8-pin SOIC arrangement. Pins 3 and 5 are the non-inverting inputs, pins 2 and 6 are the inverting inputs, pins 1 and 7 are the outputs, pin 4 is the negative supply or ground connection, and pin 8 is the positive supply connection. Confirm the pin-description table in the manufacturer datasheet before laying out the PCB.
Is MCP607T-I/SN suitable for battery-powered sensor applications?
Yes, the MCP607T-I/SN is suitable for battery-powered sensor interfaces because its typical operating current is only 18.7 uA and its single-supply range is 2.5 V to 6.0 V. Its dual-channel configuration can condition two related sensor signals while maintaining a low-power bias load. Input offset and common-mode behavior must still be checked against the sensor's output range.
What can replace MCP607T-I/SN?
The closest documented same-brand drop-in candidate is the Microchip MCP607-I/SN, which uses the same 8-pin SOIC format and belongs to the same MCP607 family. Its key electrical ratings remain closely aligned with the MCP607T-I/SN, although the ordering-code temperature designation should be compared before reuse. The MCP607T-I/ST is not treated as a separate functional alternative because its distinction is principally the ST package or ordering code.
Can MCP607-I/SN replace MCP607T-I/SN?
The MCP607-I/SN can be evaluated as a same-footprint MCP607-family replacement because the documented comparison identifies the same SOIC package family and closely aligned performance. The T and non-T ordering designations must still be checked against temperature grade, reel configuration, and purchasing requirements. Use the manufacturer cross-reference tool and current ordering table to confirm production suitability.
What is the best drop-in replacement for MCP607T-I/SN?
The MCP607-I/SN is the best-supported drop-in candidate identified for the MCP607T-I/SN because it is a member of the same MCP607 family and shares the 8-pin SOIC format. The MCP607 product page confirms the family's 155 kHz gain-bandwidth product, 18.7 uA typical operating current, and less than 250 uV offset voltage. Verify the exact suffix and lifecycle requirements before approving it for production.
When should I choose MCP607T-I/SN over MCP607-I/SN?
Choose the MCP607T-I/SN when the exact I/SN ordering code, industrial temperature designation, and manufacturer-supported reel configuration are required by the bill of materials. The MCP607-I/SN may be considered when its ordering attributes satisfy the design. Both parts are in the MCP607 family, so the deciding factors are exact suffix requirements rather than a major change in core amplifier performance.
Is MCP607T-I/SN suitable for audio preamplifier applications?
The MCP607T-I/SN can be used for low-voltage audio preamplification when the signal bandwidth and output swing meet the application requirements. Its 155 kHz gain-bandwidth product supports modest-bandwidth audio paths, while rail-to-rail output operation improves utilization of a low-voltage supply. Noise, slew rate, and maximum output amplitude must be verified in the datasheet before setting high gain.
How should MCP607T-I/SN be decoupled on a PCB?
Place the supply bypass capacitor and any recommended bulk or ceramic decoupling components close to the positive and ground pins of the MCP607T-I/SN. Keep the feedback loop and input traces compact to reduce added noise and instability. The exact capacitor values and permitted ESR range should follow the manufacturer datasheet and typical application circuit.
Is MCP607T-I/SN still active and in stock?
Microchip continues to list the MCP607 family on its official product page, and Microchip Direct lists MCP607T-I/SN inventory for immediate-order processing. Current availability can change by quantity and reel configuration. Use the Request a Quote form on this page to request current stock, lead time, and exact suffix confirmation.
Where can I buy MCP607T-I/SN online?
Use the Request a Quote form on this page to request MCP607T-I/SN availability, current unit pricing, lead time, and order quantity. The form supports an exact-match sourcing request without relying on an incorrect package suffix or reel code. Confirm that the quotation identifies MCP607T-I/SN and the required shipping and inspection details before placing the order.
What is the price of MCP607T-I/SN?
Current MCP607T-I/SN pricing depends on quantity, reel configuration, and market conditions. Use the Request a Quote form on this page for the current unit price and volume breaks for the exact ordering code. Confirm that the quote covers the 8-pin SOIC I/SN variant rather than another MCP607 temperature or package designation.
What is the lead time for MCP607T-I/SN?
The current lead time for MCP607T-I/SN should be requested through the Request a Quote form on this page, using the required quantity and reel configuration. Microchip Direct describes immediate-order processing for listed inventory, but scheduling can change with order volume and supply conditions. The quotation response should be used as the purchasing commitment.

Mühendislik referans verileri: MCP607T-I/SN — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose MCP607T-I/SN when the bill of materials specifically requires the I/SN ordering code and a dual, micropower CMOS amplifier operating from 2.5 V to 6.0 V. Its 155 kHz gain-bandwidth product is appropriate for low-bandwidth sensor, instrumentation, and signal-conditioning paths, while 18.7 uA typical operating current supports power-constrained designs. MCP607-I/SN is the closest documented same-family candidate when its exact suffix, temperature requirements, reel configuration, and lifecycle status satisfy the design. Both offer the same 8-pin SOIC footprint and closely aligned core performance. Do not substitute solely from the generic MCP607 family name; confirm channel functions, temperature grade, package dimensions, and production ordering against the manufacturer datasheet and cross-reference results.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün MCP607-I/SN
Brand Microchip Technology Microchip Technology
Package 8-pin SOIC 8-pin SOIC - same
Amplifier Configuration Dual operational amplifier Dual operational amplifier
Gain-Bandwidth Product 155 kHz 155 kHz
Typical Operating Current 18.7 uA 18.7 uA
Offset Voltage Less than 250 uV Less than 250 uV
Output Swing Rail-to-rail Rail-to-rail
Technology CMOS CMOS
Temperature Grade Industrial Industrial

Ana Farklılayıcılar

  • Low operating current for dual-channel amplification (karşılaştırma:MCP607-I/SN)
  • Two amplifiers in a compact 8-pin SOIC (karşılaştırma:MCP607-I/SN)
  • Rail-to-rail output operation from a single supply (karşılaştırma:MCP607-I/SN)

Tasarım Notları

Place the supply bypass capacitor close to pins 8 and 4, with a short return path to the ground reference. Keep amplifier inputs, feedback resistors, and output routing compact to minimize parasitic capacitance and susceptibility to injected noise. For sensor inputs, use a grounded guard or shield where appropriate, and separate sensitive input traces from switching supplies and high-current return paths.

The MCP607T-I/SN operates from 2.5 V to 6.0 V, so ensure the source voltage remains within range during startup, transient, and shutdown. Use the 18.7 uA typical operating current as a baseline for the amplifier bias budget, then add the load-dependent current of the surrounding circuit. If the source is shared with digital circuitry, provide local filtering rather than relying on remote bulk capacitance alone.

Rail-to-rail output swing does not automatically mean the input common-mode range reaches both supply rails. Verify input-range limits for the selected operating conditions, especially when a sensor can swing to 0 V or near the positive rail. Avoid allowing output saturation to drive deep into the amplifier's linear region, and check capacitive loading before adding large capacitors directly to the output.

At low closed-loop gains, excessive output capacitance or excessive loop gain can affect stability. Keep feedback components close to the amplifier and compare the selected gain with the recommended application circuits in the manufacturer datasheet. For low-level instrumentation, use short differential traces, maintain a quiet reference return, and avoid sharing high-current return paths with the input reference.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The manufacturer page identifies MCP607 as an industrial-temperature dual operational amplifier, but no specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration appears in the cited product-page text.

Veri doğrulanma tarihi: 2026-11-20 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

MCP607T-I/SN datasheet MCP607T-I/SN pinout MCP607T-I/SN datasheet pdf MCP607T-I/SN equivalent MCP607T-I/SN replacement MCP607T-I/SN cross reference MCP607T-I/SN price MCP607T-I/SN stock MCP607T-I/SN vs MCP607-I/SN Microchip MCP607T-I/SN MCP607 155 kHz micropower op amp MCP607 dual 2.5V op amp

İlgili Bileşenler ve Terimler

Microchip Technology MCP607T-I/SN MCP607-I/SN MCP607 MCP606 MCP608 MCP609 dual operational amplifier op amp analog amplifier analog integrated circuit semiconductor micropower CMOS rail-to-rail output gain-bandwidth product offset voltage operating current input bias current low-dropout regulator single-supply operation SOIC-8 QFN family surface-mount package sensor signal conditioning industrial data acquisition
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle