Texas Instruments

OPA2607H - 50 MHz Dual CMOS Operational Amplifier | Texas Instruments

MPN: OPA2607H ✓ Aktif
3.8 nV/√Hz Vdss 8-pin HSOP Package
MOQ: 1 |

OPA2607H Genel Bakış

The Texas Instruments OPA2607H is a dual-channel, low-power, precision CMOS operational amplifier with a 50 MHz gain-bandwidth product. It uses a decompensated architecture intended for stable operation at a minimum gain of 6 V/V, while its low noise of 3.8 nV/√Hz supports high-impedance signal-chain designs. The device is offered in an 8-pin HSOP package and is associated with the OPA607/OPA2607 family of general-purpose CMOS operational amplifiers.

An operational amplifier is an active analog signal-conditioning component that compares two input voltages and drives its output toward the difference between them. In a feedback circuit, the OPA2607H can provide voltage amplification, signal buffering, active filtering, impedance conversion, and analog signal conditioning. As a current-feedback operational amplifier, its decompensated design favors applications where closed-loop gain is maintained at or above the specified minimum gain rather than unity-gain operation.

The headline characteristics are a 50 MHz gain-bandwidth product, 3.8 nV/√Hz input noise, dual-channel operation, low power consumption, and a minimum stable gain of 6 V/V. These attributes make the amplifier useful in high-speed instrumentation, precision analog measurement, communications interfaces, active filters, and test-and-measurement signal paths where low input noise and high bandwidth are more important than unity-gain operation.

OPA2607H is a high-impedance CMOS operational amplifier, so its input stage is suitable for sensing weak signals without loading the source aggressively. The device is designed for general-purpose applications that require a balance between low noise, wide bandwidth, and power efficiency. Its dual-channel configuration also allows two amplifier functions to be implemented in one package when board area is constrained.

Typical applications include photodiode signal conditioning, low-level sensor amplification, active analog filters, precision current-feedback stages, communications receive paths, and laboratory measurement front ends. The manufacturer identifies the OPA607 and OPA2607 devices as decompensated, minimum-gain-6 V/V, general-purpose CMOS operational amplifiers with low noise and wide bandwidth.

Designers should confirm the required closed-loop gain, supply voltage, input and output swing, output-current capability, stability method, and package pinout against the manufacturer datasheet before implementation. Because OPA2607H is decompensated, it is not automatically interchangeable with a unity-gain-stable amplifier. Use the Request a Quote form on this page for current commercial availability, price, stock, and lead-time information.

Drop-in alternatifler için OPA2607H — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

OPA2607H/2K5

✅ Yerleştirme
📦 8-pin HSOP
Same OPA2607 dual-channel decompensated amplifier and 8-pin HSOP footprint; ordering/packing code differs by 0% in stated architecture, bandwidth, noise, and minimum gain

📋 Katalogda Olmayan Referans Alternatifi

OPA2607H Maksimum Değerlendirmeler & Elektriksel Özellikler

Amplifier Type Dual operational amplifier
Architecture Decompensated CMOS current-feedback operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 50 MHz
Input Noise Voltage Density 3.8 nV/√Hz
Minimum Stable Gain 6 V/V
Input Type High-impedance CMOS input
Paket 8-pin HSOP
Montaj Türü Surface mount

OPA2607H Pin Yapısı

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 [DATA_NEEDED: pin 1 name] — Use the pin-description table in the manufacturer datasheet.
Pin 2 [DATA_NEEDED: pin 2 name] — Use the pin-description table in the manufacturer datasheet.
Pin 3 [DATA_NEEDED: pin 3 name] — Use the pin-description table in the manufacturer datasheet.
Pin 4 [DATA_NEEDED: pin 4 name] — Use the pin-description table in the manufacturer datasheet.
Pin 5 [DATA_NEEDED: pin 5 name] — Use the pin-description table in the manufacturer datasheet.
Pin 6 [DATA_NEEDED: pin 6 name] — Use the pin-description table in the manufacturer datasheet.
Pin 7 [DATA_NEEDED: pin 7 name] — Use the pin-description table in the manufacturer datasheet.
Pin 8 [DATA_NEEDED: pin 8 name] — Use the pin-description table in the manufacturer datasheet.

Tipik Uygulamalar

OPA2607H için uygundur 6 uygulamas: Photodiode Signal Conditioning, Precision Active Filters, Communications Receive Signal Path, Precision Instrumentation Front End, Audio and Measurement Buffering, Industrial Sensor Interface.

💡

Photodiode Signal Conditioning

The OPA2607H is well suited to photodiode preamplification because its high-impedance CMOS input avoids aggressive source loading, while 3.8 nV/√Hz input noise supports weak-signal amplification and 50 MHz bandwidth preserves useful signal rise time. A typical transimpedance stage places the amplifier around the photodiode with a feedback resistor and compensation capacitor selected from the manufacturer’s stability guidance. The decompensated architecture requires a minimum stable gain of 6 V/V, so the complete feedback network, including any added gain, should be designed together rather than using a generic unity-gain transimpedance configuration.

🔧

Precision Active Filters

The OPA2607H can implement wideband active filtering stages where the 50 MHz gain-bandwidth product and 3.8 nV/√Hz noise density provide useful signal-chain headroom. Its decompensated current-feedback topology is particularly appropriate for sections designed with the manufacturer’s recommended gain and compensation values. This allows a filter to combine gain with bandwidth without forcing each stage into unity gain. Component tolerances, op-amp noise, and the sensitivity of high-Q filter sections to component variation should be evaluated during the filter-design stage.

🌐

Communications Receive Signal Path

OPA2607H is applicable to communications receive paths that benefit from high bandwidth, low input noise, and high input impedance. The 50 MHz gain-bandwidth product supports signal conditioning around communication front ends, while the 3.8 nV/√Hz noise specification is valuable when the source impedance is not extremely high. The dual-channel configuration can handle two related signal functions in one package. Because the amplifier has a minimum stable gain of 6 V/V, the receiver architecture should preserve that gain requirement or deliberately add gain before the feedback network.

🖥️

Precision Instrumentation Front End

The OPA2607H fits instrumentation amplifiers and low-level sensor interfaces that require a balance of input noise, bandwidth, and low power. Its high-impedance CMOS inputs reduce loading of sensor outputs, and the 50 MHz gain-bandwidth product supports signal bandwidth beyond ordinary precision op amps. Designers should still account for input bias current, offset voltage, sensor noise, and resistor noise. The decompensated architecture makes the gain budget important: use the minimum stable gain of 6 V/V as a hard constraint when assigning amplifier stages.

🎧

Audio and Measurement Buffering

OPA2607H can serve as a high-speed dual buffer or gain stage in audio and precision measurement circuits where the 3.8 nV/√Hz input noise and 50 MHz bandwidth provide a useful combination. In an audio measurement path, the low-noise input stage can help preserve the signal floor, while the dual package can reduce board area when two channels are required. The amplifier is not automatically suitable for unity-gain buffering because of its 6 V/V minimum stable gain; choose a unity-gain-stable device when that topology is mandatory.

🏭

Industrial Sensor Interface

OPA2607H is suitable for industrial sensor interfaces that combine low-level input signals with moderate bandwidth requirements. Its CMOS input stage provides high input impedance, and the 50 MHz gain-bandwidth product leaves bandwidth margin for filtering and downstream conversion. The low-power dual-channel configuration can help limit board-level power in multi-channel systems. Robust industrial designs should still provide input protection, verify common-mode and output-swing limits against the exact supply conditions, and confirm the operating-temperature grade required by the manufacturer ordering information.

What is the OPA2607H?
The OPA2607H is a dual-channel, low-power CMOS operational amplifier from Texas Instruments. According to the manufacturer product information, it is a decompensated, minimum-gain-6 V/V current-feedback amplifier with a 50 MHz gain-bandwidth product and input noise density of 3.8 nV/√Hz. The OPA2607H is packaged in an 8-pin HSOP and is intended for general-purpose applications requiring a balance of bandwidth, low noise, and high-impedance inputs.
What is the operating voltage of OPA2607H?
The verified manufacturer product page does not state a complete supply-voltage range for the OPA2607H in the supplied material. The OPA2607 is described as a CMOS operational amplifier, and a separate datasheet search result indicates wideband operation around plus or minus 12 V, but that context is not enough to establish every allowable input or output condition. Use the manufacturer datasheet and the Request a Quote form on this page for exact device-specific operating and commercial information.
What is the gain-bandwidth product of OPA2607H?
The OPA2607H has a 50 MHz gain-bandwidth product according to the Texas Instruments product page. This bandwidth is the key speed figure for the decompensated current-feedback architecture. Because the amplifier is specified for stable operation at a minimum gain of 6 V/V, a design should not assume that its feedback network behaves like a unity-gain-stable voltage-feedback amplifier. The closed-loop bandwidth and stability must be evaluated using the manufacturer’s recommended compensation and feedback values.
How noisy is the OPA2607H?
The OPA2607H input noise density is 3.8 nV/√Hz, as stated in the manufacturer product-page description. That figure is relevant for low-level source impedance, sensor, photodiode, and precision measurement designs where amplifier-added noise can influence the usable signal range. Noise performance is only one part of the system calculation; source resistance, bandwidth, resistor noise, input bias current, and the selected closed-loop gain also affect total input-referred noise.
Is the OPA2607H unity-gain stable?
No. The Texas Instruments product information identifies the OPA607 and OPA2607 devices as decompensated amplifiers with a minimum gain of 6 V/V. This means OPA2607H is intended for closed-loop gains of at least 6 V/V and should not be treated as a conventional unity-gain-stable op amp. If the application requires unity gain or very low gain, select an amplifier specifically designed for that stability range instead of assuming a pin-compatible substitution.
Where can I download the OPA2607H datasheet PDF?
The official Texas Instruments OPA2607 product page is the best starting point for the OPA2607H datasheet, product parameters, ordering information, and related support documents. The manufacturer page identifies the part as a dual-channel, low-power, precision CMOS operational amplifier. Use the product page’s datasheet link for the authoritative PDF revision, pin description, electrical limits, stability guidance, and ordering codes. Avoid relying on third-party copies when an official manufacturer document is required for design release.
Where is the OPA2607H pinout?
The OPA2607H uses an 8-pin HSOP package, and the exact pin names and numbering should be taken from the pin-description table in the Texas Instruments OPA2607 datasheet. The verified material confirms an 8-HSOP package but does not reproduce the individual pin assignments. Use that table when assigning supply, ground, input, output, feedback, and compensation connections so that PCB tracks match the manufacturer’s standard numbering.
What can replace the OPA2607H?
A true drop-in replacement must use the same package and pin configuration and preserve the decompensated minimum-gain requirement of 6 V/V. The verified cross-reference results identify OPA2607H/2K5 as a related exact-family ordering option, while broader cross-reference searches did not establish additional pin-compatible alternatives with complete electrical data. Treat the family ordering option as a packaging or ordering distinction and confirm the exact suffix, lead style, temperature grade, and datasheet limits before replacement.
What is the best Analog Devices equivalent for OPA2607H?
The verified cross-reference material does not establish a specific Analog Devices part as a pin-compatible replacement for the OPA2607H. A valid substitute must match the 8-pin HSOP footprint, dual-channel configuration, minimum stable gain of 6 V/V, and current-feedback compensation behavior. Analog Devices has related high-speed CMOS amplifiers, but a family-level similarity is not sufficient evidence for a drop-in substitution. Compare the complete manufacturer pinout and stability requirements before considering any alternate manufacturer.
OPA2607H vs OPA2607H/2K5: which one should I choose?
OPA2607H and OPA2607H/2K5 identify ordering variants of the same OPA2607 family rather than different amplifier architectures. The verified listings identify the device as an 8-pin HSOP dual CMOS amplifier, and the slash-suffixed ordering code may represent different reel or packing conventions. For design equivalence, compare the manufacturer ordering table, package dimensions, temperature range, and marking information. For purchasing, use the Request a Quote form and provide the complete suffix when requesting supply.
When should I choose the OPA2607H over a unity-gain-stable op amp?
Choose the OPA2607H when the design requires a decompensated current-feedback amplifier, a minimum closed-loop gain of 6 V/V, 50 MHz gain-bandwidth capability, and low input noise. It is particularly relevant to high-speed active filters, photodiode stages, communications signal paths, and instrumentation. Choose a unity-gain-stable amplifier instead when the circuit requires unity-gain operation, because changing the compensation class without changing the feedback network can create instability or unexpected bandwidth behavior.
Is the OPA2607H suitable for photodiode signal conditioning?
The OPA2607H is a strong candidate for photodiode front ends because the manufacturer describes it as a high-impedance CMOS input amplifier with 3.8 nV/√Hz noise and 50 MHz bandwidth. Its current-feedback architecture can support high-gain, high-speed signal conditioning when the feedback and compensation network follows the datasheet. Practical design still requires attention to photodiode capacitance, input bias current, dark current, connector leakage, and the noise contribution of the feedback resistors.
Does the OPA2607H require external compensation?
The OPA2607H is decompensated and has a specified minimum stable gain of 6 V/V, so its stability depends on the closed-loop gain and the feedback network. The exact compensation requirements, including any external components, should be taken from the OPA2607 datasheet’s stability and application sections. Do not copy a unity-gain compensation network from another current-feedback amplifier, and verify the selected feedback resistor and noise-gain values against the manufacturer’s recommended configurations.
How much output current can OPA2607H deliver?
The verified material does not provide the OPA2607H output-current limit, so the exact maximum should not be inferred from the family description. Output-current capability depends on supply voltage, output voltage, load, channel configuration, and thermal conditions. Use the manufacturer datasheet’s electrical characteristics and output-current-versus-output-voltage information for the exact device. Request the current commercial quotation through the Request a Quote form on this page rather than relying on an unconfirmed stock or price statement.
Is OPA2607H RoHS compliant and available for quotation?
The exact RoHS, REACH, lead-free, and halogen-free status for OPA2607H is not stated in the verified material, so the compliance fields are recorded as unknown rather than assumed. The Texas Instruments product page is the authoritative starting point for current environmental and ordering information. For availability, current pricing, stock, and lead time, submit the complete OPA2607H part number through the Request a Quote form on this page.

Mühendislik referans verileri: OPA2607H — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose OPA2607H when your circuit needs a dual decompensated CMOS amplifier with a 50 MHz gain-bandwidth product, 3.8 nV/√Hz input noise density, and a minimum stable gain of 6 V/V. It is well matched to photodiode amplifiers, active filters, communications receive paths, instrumentation front ends, and industrial sensor interfaces. OPA2607H/2K5 is the closely related ordering variant identified in the manufacturer-family listings; use it when the approved purchasing code specifies that suffix, after checking package, temperature, and packing details. Do not substitute a unity-gain-stable amplifier unless the feedback network is redesigned, because the decompensated architecture changes stability requirements. For designs requiring unity gain, lower noise, lower power, or a different package, compare the required gain, bandwidth, input impedance, supply range, output swing, and stability profile against a specifically rated amplifier rather than relying on general family similarity.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün OPA2607H/2K5
Package 8-pin HSOP 8-pin HSOP
Brand Texas Instruments Texas Instruments
Channel Count 2 channels 2 channels
Gain-Bandwidth Product 50 MHz 50 MHz
Input Noise Density 3.8 nV/√Hz 3.8 nV/√Hz
Minimum Stable Gain 6 V/V 6 V/V
Architecture Decompensated CMOS current-feedback Decompensated CMOS current-feedback
Input Type High-impedance CMOS High-impedance CMOS

Ana Farklılayıcılar

  • Decompensated high-speed architecture (karşılaştırma:OPA2607H/2K5)
  • Low-noise precision signal conditioning (karşılaştırma:OPA2607H/2K5)
  • High-impedance CMOS input stage (karşılaştırma:OPA2607H/2K5)

Tasarım Notları

Do not design the OPA2607H as a unity-gain-stable amplifier. Texas Instruments identifies the device as decompensated with a minimum stable gain of 6 V/V, so a feedback network that works at unity gain on a conventional op amp can produce instability or unexpected frequency response. Select feedback resistors and compensation components from the manufacturer’s recommended application circuits, and validate the complete loop gain and phase margin at the intended signal frequency.

Keep the high-impedance input path short and minimize leakage around the OPA2607H. Use a clean ground reference, guard sensitive input nodes where appropriate, and place input-bias-current compensation close to the amplifier. When the source impedance is high, input capacitance, board contamination, and leakage current can dominate the 3.8 nV/√Hz voltage-noise specification, so clean assembly practices are part of achieving the expected low-noise performance.

Place input, feedback, and compensation components close to the OPA2607H pins and route the feedback loop with minimal parasitic capacitance. Keep the feedback trace short and avoid routing it beneath noisy switching or digital signals. Because the device uses a current-feedback topology, component placement and parasitic effects can affect compensation and loop stability; confirm the layout against the manufacturer datasheet before releasing the PCB.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The verified product and distributor results do not state the device-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes on the current Texas Instruments product and ordering documentation.

İlgili Aramalar

OPA2607H datasheet OPA2607H pinout OPA2607H datasheet pdf OPA2607H 8-pin HSOP OPA2607H 50 MHz OPA2607H 3.8 nV/√Hz OPA2607H minimum gain 6 V/V OPA2607H photodiode amplifier OPA2607H active filter OPA2607H vs OPA2607H/2K5 OPA2607H drop-in replacement OPA2607H price OPA2607H stock Texas Instruments OPA2607H OPA2607H application circuit

İlgili Bileşenler ve Terimler

Texas Instruments OPA2607H OPA2607H/2K5 OPA2607 OPA607 dual operational amplifier CMOS operational amplifier current-feedback amplifier decompensated amplifier gain-bandwidth product input noise density high-impedance input minimum stable gain 8-pin HSOP HSOP package surface-mount package photodiode signal conditioning active filter communications receiver precision instrumentation industrial sensor interface signal conditioning semiconductor
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle