OPA2607H - 50 MHz Dual CMOS Operational Amplifier | Texas Instruments
부품 번호: OPA2607H ✓ 활성OPA2607H 개요
An operational amplifier is an active analog signal-conditioning component that compares two input voltages and drives its output toward the difference between them. In a feedback circuit, the OPA2607H can provide voltage amplification, signal buffering, active filtering, impedance conversion, and analog signal conditioning. As a current-feedback operational amplifier, its decompensated design favors applications where closed-loop gain is maintained at or above the specified minimum gain rather than unity-gain operation.
The headline characteristics are a 50 MHz gain-bandwidth product, 3.8 nV/√Hz input noise, dual-channel operation, low power consumption, and a minimum stable gain of 6 V/V. These attributes make the amplifier useful in high-speed instrumentation, precision analog measurement, communications interfaces, active filters, and test-and-measurement signal paths where low input noise and high bandwidth are more important than unity-gain operation.
OPA2607H is a high-impedance CMOS operational amplifier, so its input stage is suitable for sensing weak signals without loading the source aggressively. The device is designed for general-purpose applications that require a balance between low noise, wide bandwidth, and power efficiency. Its dual-channel configuration also allows two amplifier functions to be implemented in one package when board area is constrained.
Typical applications include photodiode signal conditioning, low-level sensor amplification, active analog filters, precision current-feedback stages, communications receive paths, and laboratory measurement front ends. The manufacturer identifies the OPA607 and OPA2607 devices as decompensated, minimum-gain-6 V/V, general-purpose CMOS operational amplifiers with low noise and wide bandwidth.
Designers should confirm the required closed-loop gain, supply voltage, input and output swing, output-current capability, stability method, and package pinout against the manufacturer datasheet before implementation. Because OPA2607H is decompensated, it is not automatically interchangeable with a unity-gain-stable amplifier. Use the Request a Quote form on this page for current commercial availability, price, stock, and lead-time information.
드롭인 대체품: OPA2607H — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
OPA2607H/2K5
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
OPA2607H 최대 정격 & 전기적 특성
| Amplifier Type | Dual operational amplifier |
| Architecture | Decompensated CMOS current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 50 MHz |
| Input Noise Voltage Density | 3.8 nV/√Hz |
| Minimum Stable Gain | 6 V/V |
| Input Type | High-impedance CMOS input |
| 패키지 | 8-pin HSOP |
| 실장 유형 | Surface mount |
OPA2607H 핀 구성
| 핀 1 | [DATA_NEEDED: pin 1 name] — Use the pin-description table in the manufacturer datasheet. |
| 핀 2 | [DATA_NEEDED: pin 2 name] — Use the pin-description table in the manufacturer datasheet. |
| 핀 3 | [DATA_NEEDED: pin 3 name] — Use the pin-description table in the manufacturer datasheet. |
| 핀 4 | [DATA_NEEDED: pin 4 name] — Use the pin-description table in the manufacturer datasheet. |
| 핀 5 | [DATA_NEEDED: pin 5 name] — Use the pin-description table in the manufacturer datasheet. |
| 핀 6 | [DATA_NEEDED: pin 6 name] — Use the pin-description table in the manufacturer datasheet. |
| 핀 7 | [DATA_NEEDED: pin 7 name] — Use the pin-description table in the manufacturer datasheet. |
| 핀 8 | [DATA_NEEDED: pin 8 name] — Use the pin-description table in the manufacturer datasheet. |
일반적인 애플리케이션
OPA2607H 적합 용도: 6 애플리케이션s: Photodiode Signal Conditioning, Precision Active Filters, Communications Receive Signal Path, Precision Instrumentation Front End, Audio and Measurement Buffering, Industrial Sensor Interface.
Photodiode Signal Conditioning
The OPA2607H is well suited to photodiode preamplification because its high-impedance CMOS input avoids aggressive source loading, while 3.8 nV/√Hz input noise supports weak-signal amplification and 50 MHz bandwidth preserves useful signal rise time. A typical transimpedance stage places the amplifier around the photodiode with a feedback resistor and compensation capacitor selected from the manufacturer’s stability guidance. The decompensated architecture requires a minimum stable gain of 6 V/V, so the complete feedback network, including any added gain, should be designed together rather than using a generic unity-gain transimpedance configuration.
추천
Precision Active Filters
The OPA2607H can implement wideband active filtering stages where the 50 MHz gain-bandwidth product and 3.8 nV/√Hz noise density provide useful signal-chain headroom. Its decompensated current-feedback topology is particularly appropriate for sections designed with the manufacturer’s recommended gain and compensation values. This allows a filter to combine gain with bandwidth without forcing each stage into unity gain. Component tolerances, op-amp noise, and the sensitivity of high-Q filter sections to component variation should be evaluated during the filter-design stage.
추천
Communications Receive Signal Path
OPA2607H is applicable to communications receive paths that benefit from high bandwidth, low input noise, and high input impedance. The 50 MHz gain-bandwidth product supports signal conditioning around communication front ends, while the 3.8 nV/√Hz noise specification is valuable when the source impedance is not extremely high. The dual-channel configuration can handle two related signal functions in one package. Because the amplifier has a minimum stable gain of 6 V/V, the receiver architecture should preserve that gain requirement or deliberately add gain before the feedback network.
추천
Precision Instrumentation Front End
The OPA2607H fits instrumentation amplifiers and low-level sensor interfaces that require a balance of input noise, bandwidth, and low power. Its high-impedance CMOS inputs reduce loading of sensor outputs, and the 50 MHz gain-bandwidth product supports signal bandwidth beyond ordinary precision op amps. Designers should still account for input bias current, offset voltage, sensor noise, and resistor noise. The decompensated architecture makes the gain budget important: use the minimum stable gain of 6 V/V as a hard constraint when assigning amplifier stages.
추천
Audio and Measurement Buffering
OPA2607H can serve as a high-speed dual buffer or gain stage in audio and precision measurement circuits where the 3.8 nV/√Hz input noise and 50 MHz bandwidth provide a useful combination. In an audio measurement path, the low-noise input stage can help preserve the signal floor, while the dual package can reduce board area when two channels are required. The amplifier is not automatically suitable for unity-gain buffering because of its 6 V/V minimum stable gain; choose a unity-gain-stable device when that topology is mandatory.
추천
Industrial Sensor Interface
OPA2607H is suitable for industrial sensor interfaces that combine low-level input signals with moderate bandwidth requirements. Its CMOS input stage provides high input impedance, and the 50 MHz gain-bandwidth product leaves bandwidth margin for filtering and downstream conversion. The low-power dual-channel configuration can help limit board-level power in multi-channel systems. Robust industrial designs should still provide input protection, verify common-mode and output-swing limits against the exact supply conditions, and confirm the operating-temperature grade required by the manufacturer ordering information.
추천
엔지니어링 참조 데이터: OPA2607H — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | OPA2607H/2K5 |
|---|---|---|
| Package | 8-pin HSOP | 8-pin HSOP |
| Brand | Texas Instruments | Texas Instruments |
| Channel Count | 2 channels | 2 channels |
| Gain-Bandwidth Product | 50 MHz | 50 MHz |
| Input Noise Density | 3.8 nV/√Hz | 3.8 nV/√Hz |
| Minimum Stable Gain | 6 V/V | 6 V/V |
| Architecture | Decompensated CMOS current-feedback | Decompensated CMOS current-feedback |
| Input Type | High-impedance CMOS | High-impedance CMOS |
주요 차별점
- Decompensated high-speed architecture (vs OPA2607H/2K5)
- Low-noise precision signal conditioning (vs OPA2607H/2K5)
- High-impedance CMOS input stage (vs OPA2607H/2K5)
설계 노트
Do not design the OPA2607H as a unity-gain-stable amplifier. Texas Instruments identifies the device as decompensated with a minimum stable gain of 6 V/V, so a feedback network that works at unity gain on a conventional op amp can produce instability or unexpected frequency response. Select feedback resistors and compensation components from the manufacturer’s recommended application circuits, and validate the complete loop gain and phase margin at the intended signal frequency.
Keep the high-impedance input path short and minimize leakage around the OPA2607H. Use a clean ground reference, guard sensitive input nodes where appropriate, and place input-bias-current compensation close to the amplifier. When the source impedance is high, input capacitance, board contamination, and leakage current can dominate the 3.8 nV/√Hz voltage-noise specification, so clean assembly practices are part of achieving the expected low-noise performance.
Place input, feedback, and compensation components close to the OPA2607H pins and route the feedback loop with minimal parasitic capacitance. Keep the feedback trace short and avoid routing it beneath noisy switching or digital signals. Because the device uses a current-feedback topology, component placement and parasitic effects can affect compensation and loop stability; confirm the layout against the manufacturer datasheet before releasing the PCB.
규정 준수 정보
The verified product and distributor results do not state the device-specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Confirm these attributes on the current Texas Instruments product and ordering documentation.