Texas Instruments

OPA336PA - 20uA Low-Power CMOS Op Amp | Texas Instruments

MPN: OPA336PA ✓ Aktif
2.1 V Vdss 20uA per amplifier Id 8-pin PDIP Package
MOQ: 1 |

OPA336PA Genel Bakış

The Texas Instruments OPA336PA is a single-supply, micropower CMOS operational amplifier with a typical quiescent current of 20uA per amplifier, a maximum offset voltage of 125uV, a typical input bias current of 1pA, and an open-loop gain of 115dB. The device is packaged in an 8-pin PDIP package and is designed for low-voltage battery-powered systems.

A CMOS operational amplifier is a voltage-controlled, differential-input amplifier using complementary MOS transistors. It provides voltage gain, filtering, buffering, and signal conditioning while operating from a single positive supply. The OPA336 belongs to the microAmplifier family and is positioned for portable, industrial, and instrumentation circuits where low supply current, rail-to-rail output behavior, and low input bias current are important. Its common-mode input range extends to the negative supply, supporting systems that operate from 2.1V to 5.5V.

Key features of the OPA336PA include a 20uA quiescent current per amplifier, 125uV maximum offset voltage, 1pA input bias current, and 115dB open-loop gain. The output is rail-to-rail and swings to within 3mV of the supply rails with a 100kohm load. These characteristics make the device useful in battery-powered sensor interfaces, current-loop measurements, low-level signal conditioning, and precision analog systems.

The OPA336 series uses CMOS input and output stages to provide low power consumption and high input impedance. Its 100kHz gain-bandwidth product is sufficient for many low-frequency measurement and control paths. Because the amplifier operates from a single supply, the negative common-mode range reaching the negative rail is valuable for unipolar sensor systems, where signal voltages can approach ground without requiring a negative supply.

Typical applications include portable electrochemical sensors, biomedical instrumentation, battery-powered monitors, low-current transducers, and low-power signal-conditioning modules. The low input bias current minimizes error when the source resistance is high, while the small quiescent current helps preserve battery capacity. The rail-to-rail output improves usable signal range in compact single-supply systems.

When designing around the OPA336PA, check input and output common-mode limits, bias-current error, capacitive-load stability, and the voltage drop across the output when driving heavier loads. Place bypass capacitors close to the supply pins and keep sensitive input routing short to minimize leakage and coupling. The 8-pin PDIP package is suitable for through-hole prototypes and legacy industrial equipment, although modern compact designs may require an alternative package option.

This product page combines the manufacturer’s operating characteristics with engineering guidance covering application fit, pin-compatible alternatives, parameter comparisons, and practical circuit implementation considerations.

Drop-in alternatifler için OPA336PA — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller OPA336PA (aynı form faktörü ve ayağa oturma) — farklı olan Open-Loop Gain, Quiescent Current.

Texas Instruments
Open-Loop Gain: 115 dB typical
Quiescent Current: 20 uA per amplifier typical
İle Karşılaştır OPA336PA →

OPA336P

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
Texas Instruments
📦 8-pin PDIP
Single operational amplifier · 1 channel · 20 uA per amplifier typical · 125 uV maximum · 1 pA · 115 dB typical · Single supply · Rail-to-rail input

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

OPA336PAG4

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin PDIP
Same OPA336 family and 8-pin PDIP footprint; ordering suffix differs by 0% in pin count and package body size.

📋 Katalogda Olmayan Referans Alternatifi

OPA336PA Maksimum Değerlendirmeler & Elektriksel Özellikler

Amplifier Type Single operational amplifier
Technology CMOS
Number of Channels 1 channel
Minimum Supply Voltage 2.1 V
Maximum Supply Voltage 5.5 V
Supply Type Single supply
Durağan Akım 20uA per amplifier
Maximum Offset Voltage 125uV
Typical Input Bias Current 1pA
Open-Loop Gain 115dB
Gain-Bandwidth Product 100kHz
Output Swing Within 3mV of the supplies at 100kohm load
Common-Mode Input Range Extends to the negative supply
Çıkış Türü Rail-to-rail
Paket 8-pin PDIP
Montaj Türü Through-hole

OPA336PA Pin Yapısı

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 NC — Not connected
Pin 2 IN- — Inverting input
Pin 3 IN+ — Non-inverting input
Pin 4 V- — Negative supply
Pin 5 NC — Not connected
Pin 6 OUT — Output
Pin 7 V+ — Positive supply
Pin 8 NC — Not connected

Tipik Uygulamalar

OPA336PA için uygundur 6 uygulamas: Battery-Powered Sensor Interface, Portable Medical Monitoring, Low-Current Transducer Conditioning, Industrial Process Monitoring, Low-Leakage Current Measurement, Low-Power Data Acquisition.

🔋

Battery-Powered Sensor Interface

The OPA336PA fits battery-powered sensor interfaces because its 20uA per-amplifier quiescent current limits standby consumption, while its 1pA typical input bias current reduces loading on high-impedance sensors. Operation from a single supply as low as 2.1V supports compact energy-harvesting and portable measurement systems. The common-mode input range extending to the negative supply also allows signals near ground to be amplified without adding a negative rail. In a typical circuit, the amplifier buffers or conditions a sensor output before a converter or controller samples it. Designers should still budget for load current, sensor leakage, and the energy consumed by external filtering components.

💊

Portable Medical Monitoring

The OPA336PA is appropriate for portable medical monitoring because its low 20uA per-amplifier supply current supports battery-operated instruments and its 1pA typical input bias current minimizes disturbance to high-impedance bio-sensing paths. The 125uV maximum offset voltage supports low-level signal conditioning, while the 115dB open-loop gain provides useful amplification for sensor-amplifier stages. A typical implementation places the device close to the sensor connector and uses it to amplify a weak differential or single-ended signal before filtering and digitization. Medical designs require appropriate signal isolation, protection, leakage evaluation, and validation for the intended measurement function.

🖥️

Low-Current Transducer Conditioning

OPA336PA suits low-current transducer conditioning because its 1pA typical input bias current creates less error with high-value source resistors, and its 20uA quiescent current keeps instrumentation power requirements modest. The 100kHz gain-bandwidth product is appropriate for slowly varying or low-frequency measurement signals rather than wideband waveforms. Designers can use the amplifier in a non-inverting or transimpedance topology, provided the selected feedback network remains compatible with the amplifier’s operating range. The rail-to-rail output provides useful headroom at low supply voltage, although output loading can increase supply current and reduce the benefit of the low-power architecture.

🏭

Industrial Process Monitoring

The OPA336PA can support industrial process-monitoring circuits where low power, high input impedance, and single-supply operation are valuable. Its common-mode input range extends to the negative supply, helping process sensors produce signals close to ground, while the 125uV maximum offset voltage supports low-level amplification. The device can condition the output of a resistive or current-based sensor before an ADC input. Industrial implementation should include transient protection, appropriate grounding, and verified noise immunity around motors, relays, and switching converters. The 100kHz bandwidth is suitable for many slowly changing process variables but not for high-speed waveform monitoring.

⚡

Low-Leakage Current Measurement

OPA336PA is well suited to current measurement because its 1pA typical input bias current reduces the measurement error contributed by the amplifier when the shunt or sensor impedance is high. The 115dB open-loop gain supports accurate closed-loop amplification, and the single-supply operation simplifies portable instrumentation. In a transimpedance amplifier, the feedback resistor and compensation capacitor must be selected around the device’s 100kHz gain-bandwidth product and stability requirements. Low bias current alone does not eliminate errors from resistor tolerance, input leakage, contamination, or dielectric absorption, so the complete measurement chain must be evaluated as a system.

📊

Low-Power Data Acquisition

OPA336PA fits low-power data-acquisition front ends that operate from a 2.1V to 5.5V single supply. Its 20uA per-amplifier quiescent current reduces consumption in portable acquisition systems, while the rail-to-rail output can use much of the available supply range. The amplifier can condition a sensor before conversion by an ADC or energy-harvesting supply. Input filtering, output settling, and ADC acquisition timing should be checked together because the amplifier bandwidth is 100kHz. A common-mode range extending to the negative rail simplifies zero-centered unipolar sensor measurements, although system grounding must remain clean to avoid converting return-path noise into measurement error.

What is the operating voltage of OPA336PA?
The OPA336PA operates from a single supply as low as 2.1V, with a maximum listed supply voltage of 5.5V. According to the Texas Instruments OPA336 product page, the device is intended for battery-powered and other low-voltage applications. The single-supply architecture also allows its common-mode input range to extend to the negative supply, which is useful for sensor signals operating near ground.
What are the key specifications of OPA336PA that engineers should know?
The OPA336PA combines 20uA quiescent current per amplifier, 125uV maximum offset voltage, 1pA typical input bias current, and 115dB open-loop gain. It also provides a 100kHz gain-bandwidth product and rail-to-rail output that reaches within 3mV of the supply rails with a 100kohm load. These characteristics make it suitable for low-power precision analog signal conditioning.
Is the OPA336PA rail-to-rail?
Yes, the OPA336PA has a rail-to-rail output that swings to within 3mV of the positive and negative supplies with a 100kohm load, according to the Texas Instruments OPA336 product page. The common-mode input range extends to the negative supply, but the operating input range still requires attention when the output must approach the positive rail under heavy load.
Why is the 1pA input bias current of OPA336PA important?
The 1pA typical input bias current minimizes the voltage error created when the amplifier drives a high source resistance. For example, a high-value sensor resistor converts even small bias current into an input-voltage offset that can corrupt a low-level measurement. The OPA336PA is therefore useful for high-impedance sensors, current-measurement nodes, and battery-powered instrumentation where amplifier loading must remain small.
What is the best drop-in replacement for OPA336PA?
The closest same-package replacement identified for the OPA336PA is the Texas Instruments OPA336P, which uses the same 8-pin PDIP format and the same OPA336 family characteristics. Before production substitution, confirm the exact ordering suffix, pin orientation, supply range, offset limit, and electrical performance against the manufacturer datasheet. PCB changes are not expected when both devices use the standard 8-pin PDIP footprint.
Can OPA336P replace OPA336PA?
Yes, the OPA336P can serve as a drop-in option for the OPA336PA because both are members of the same Texas Instruments OPA336 family and use the 8-pin PDIP package. Their shared operating characteristics include single-supply operation from 2.1V, 20uA quiescent current per amplifier, and rail-to-rail output behavior. Verify the ordering code and pinout against the current manufacturer documentation before substitution.
OPA336PA vs OPA336UAG4 - which is better for a through-hole design?
The OPA336PA is the appropriate choice for a new through-hole design because it uses an 8-pin PDIP package. The OPA336UAG4 is associated with a surface-mount package and therefore requires a different PCB footprint even though it belongs to the same amplifier family. Both provide the OPA336 performance family, but package interchangeability is not sufficient to make the surface-mount variant a drop-in replacement.
When should I choose OPA336PA over a higher-speed op amp?
Choose the OPA336PA when battery life and very low input bias current matter more than wideband performance. Its 20uA per-amplifier quiescent current and 1pA typical input bias current suit high-impedance, low-frequency sensor paths, while the 100kHz gain-bandwidth product is appropriate for measurement and control signals rather than high-speed waveform or video chains.
Is OPA336PA suitable for battery-powered sensor interfaces?
Yes, the OPA336PA is suitable for battery-powered sensor interfaces because it operates from 2.1V, consumes 20uA per amplifier, and has a 1pA typical input bias current. Its common-mode input range extends to the negative supply, allowing many unipolar sensors to interface without a negative rail. Output loading, sensor leakage, and the amplifier’s own supply consumption must still be included in the complete power budget.
Where can I download the OPA336PA datasheet PDF?
The OPA336PA datasheet and ordering information are available from the Texas Instruments OPA336 product page at https://www.ti.com/product/OPA336. Select the datasheet link for the family document, then confirm that the ordering table includes the OPA336PA PDIP package. The pin description and electrical characteristic tables in that document should be used as the authority for layout and production substitution.
Where can I find the OPA336PA pinout?
The OPA336PA pinout is shown in the pin configuration and pin description tables of the Texas Instruments OPA336 datasheet. The device uses an 8-pin PDIP package with pin 1 identified by the package marking convention. Assign PCB connections from the manufacturer pin table rather than inferring connections from another package option, because the same amplifier family may also be offered in surface-mount packages.
How should the OPA336PA be decoupled on a PCB?
Place the supply bypass capacitor as close as practical to the OPA336PA supply and ground pins, with a short, low-inductance connection between them. Add a second smaller capacitor when the power net is long or shared with switching circuitry. Keep the input and output routes compact, avoid placing high-impedance traces beside fast digital lines, and preserve a quiet ground return to minimize noise and supply-induced offset errors.
How much power does OPA336PA consume at 3V?
Estimated: with a 3.0V supply and 20uA quiescent current per amplifier, the ideal no-load supply power is 3.0V multiplied by 20uA, or 60uW. Actual consumption increases when the output drives a load because additional current is drawn from the supply. This calculation excludes load current, output-swing current, leakage, and any external circuitry connected to the amplifier.
Where to buy OPA336PA online?
Use the Request a Quote form on this page to request OPA336PA availability, current pricing, minimum order quantity, and lead time for the exact 8-pin PDIP ordering suffix. The form connects the request directly with the XAIPART sales process without presenting a static price that may become outdated. Include the target quantity, delivery location, and required production or inspection dates in the request.
What is the price of OPA336PA?
Current OPA336PA pricing depends on quantity, package availability, and purchasing conditions, so use the Request a Quote form on this page for an amount tied to your order. The structured pricing area can also display a current quote when the part is available. For design budgeting, evaluate the effect of shipment quantity and supply continuity rather than relying on a single unit-price figure.
What is the lead time for OPA336PA and is it in stock?
Request the current OPA336PA lead time and inventory status through the Request a Quote form on this page. Availability can change with order quantity, package stock, and manufacturer replenishment, and a listing does not by itself guarantee a confirmed allocation. Include your required delivery date so the sales team can quote the available schedule for the exact OPA336PA ordering code.

Mühendislik referans verileri: OPA336PA — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the OPA336PA for new through-hole designs that require a single, low-power CMOS operational amplifier with a 2.1V minimum supply, 20uA quiescent current, 1pA typical input bias current, and rail-to-rail output behavior. It is particularly suitable for battery-powered sensors, portable measurement equipment, and low-level signal-conditioning stages. The OPA336P is a practical same-family alternative when its ordering suffix better matches an existing approved BOM or inventory plan. The OPA336PAG4 is another same-package family option, but production use should depend on confirmation of its current ordering status and electrical specifications. Surface-mount OPA336 variants are not drop-in replacements because their PCB footprints differ. For high-speed signal chains, choose an amplifier with a substantially wider gain-bandwidth product; for multi-amplifier circuits, a dual or quad device may reduce package count, but those packages also require different PCB layouts.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün OPA336P OPA336PAG4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 8-pin PDIP 8-pin PDIP - same 8-pin PDIP - same
Amplifier Type Single operational amplifier Single operational amplifier Single operational amplifier
Minimum Supply Voltage 2.1 V 2.1 V 2.1 V
Maximum Supply Voltage 5.5 V 5.5 V 5.5 V
Quiescent Current 20uA per amplifier 20uA per amplifier 20uA per amplifier
Maximum Offset Voltage 125uV 125uV 125uV
Input Bias Current 1pA typical 1pA typical 1pA typical
Open-Loop Gain 115dB 115dB 115dB
Gain-Bandwidth Product 100kHz 100kHz 100kHz

Ana Farklılayıcılar

  • Very low amplifier quiescent current (karşılaştırma:OPA336P)
  • Low input bias for high-impedance signals (karşılaştırma:OPA336PAG4)
  • Single-supply rail-to-rail operation (karşılaştırma:OPA336P)

Tasarım Notları

Place the supply bypass capacitor close to the OPA336PA V+ and V- pins, with a short ground path and minimal loop area. If the device is several centimeters from the supply source, add a second smaller capacitor at the pins to suppress high-frequency supply noise. Keep the amplifier ground return continuous and avoid routing sensitive input traces directly beside digital clocks, switch-node copper, or inductor connections.

High-impedance input traces can collect leakage, contamination, and capacitive pickup because the OPA336PA operates with 1pA typical input bias current. Keep feedback resistors close to the amplifier, avoid long exposed high-impedance nodes, and use guarding where practical. For transimpedance designs, calculate the feedback capacitance with the 100kHz gain-bandwidth product rather than relying only on a generic transimpedance formula.

Do not assume that a rail-to-rail output reaches the positive supply under every load condition. The stated 3mV output margin applies with a 100kohm load, so heavier loads can require additional output headroom. Also verify that the input and output remain inside the operating ranges at minimum supply voltage, especially when using gain near the positive rail or driving a capacitive load.

Estimated: at a 3.0V supply and 20uA quiescent current, no-load supply power is 60uW. Actual consumption also includes output-current demand and external circuit losses, so use 60uW as the amplifier-only baseline rather than a complete battery-life figure. Account for the load, sensor current, voltage regulator efficiency, and leakage over the intended operating mode when sizing the power source.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The OPA336PA is an operational amplifier rather than an automotive-qualified component. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer’s current product documentation.

Veri doğrulanma tarihi: 2026-11-09 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

OPA336PA datasheet OPA336PA pinout OPA336PA datasheet pdf OPA336PA specifications OPA336PA equivalent OPA336PA replacement OPA336PA cross reference OPA336PA footprint OPA336PA price OPA336PA stock Texas Instruments OPA336PA OPA336PA vs OPA336P OPA336 battery powered sensor OPA336 rail to rail op amp

İlgili Bileşenler ve Terimler

Texas Instruments OPA336PA OPA336P OPA336PAG4 OPA336 microAmplifier CMOS operational amplifier operational amplifier analog amplifier semiconductor single-supply operation rail-to-rail output quiescent current input bias current offset voltage open-loop gain gain-bandwidth product common-mode input range 8-pin PDIP DIP package through-hole package battery-powered applications sensor interface transimpedance amplifier
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle