OPA342UA - 1MHz RRIO CMOS Op Amp | Texas Instruments
MPN: OPA342UA ✓ AktifOPA342UA Genel Bakış
An operational amplifier is a voltage-gain component used to amplify small signals, buffer high-impedance sources, perform analog calculations, and build feedback-control loops. The OPA342 belongs to the rail-to-rail operational-amplifier family, where rail-to-rail input behavior permits operation near the supply rails and rail-to-rail output behavior improves dynamic range on low-voltage systems. It is part of the broader amplifier IC and signal-conditioning product hierarchy.
Key characteristics include a 1 MHz gain-bandwidth product, 0.2 pA typical input bias current, rail-to-rail input and output operation, and a typical quiescent current of 150 µA. The input common-mode range extends 300 mV beyond the supply rails, which helps preserve input range near the rails. The 2.7 V to 5.5 V operating range supports low-voltage portable equipment, sensor interfaces, audio paths, and industrial control systems.
The CMOS design emphasizes low power and low bias current rather than high bandwidth. The manufacturer describes the OPA342 series as optimized for low-cost, low-power, miniature applications that can use a single supply. Its 1 MHz bandwidth is suitable for moderate-frequency signal conditioning, while the very low bias current is advantageous when driving high-impedance sensors or guarding against leakage errors.
Typical uses include low-power sensor conditioning, portable measurement systems, audio input stages, and general-purpose analog buffering. In a sensor interface, the low bias current limits disturbance of high-impedance sources; in an audio path, rail-to-rail input and output operation helps preserve signal range from a 2.5 V or 3.3 V supply.
Layout should keep the input and feedback paths short and provide a solid ground return. Decoupling capacitors should be placed close to the supply pins, and the unused input must be biased within the amplifier's input common-mode range. Stable operation with capacitive loads should be verified because the feedback network and output loading determine the response.
This page organizes the OPA342UA specifications, practical application guidance, compatible-device analysis, and design considerations into a buyer-focused engineering reference for selecting and implementing the device.
Drop-in alternatifler için OPA342UA — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller OPA342UA (aynı form faktörü ve ayağa oturma) — farklı olan Gain-Bandwidth Product.
OPA338UA
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →OPA342UA Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Single operational amplifier |
| Technology | CMOS |
| Gain-Bandwidth Product | 1 MHz |
| Maximum Supply Voltage | 5.5 V |
| İşletim Besleme Gerilimi | 2.7 V to 5.5 V |
| Minimum Single-Supply Operation | 2.5 V |
| Input Bias Current | 0.2 pA typical |
| Durağan Akım | 150 µA typical |
| Input Common-Mode Range | Extends 300 mV beyond the supply rails |
| Input Common-Mode Operation | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Number of Channels | 1 channel |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
| Application Category | General-purpose instrumentation amplifier |
OPA342UA Pin Yapısı
| Pin 1 | NC — Not connected |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT — Output |
| Pin 7 | V+ — Positive supply connection |
| Pin 8 | NC — Not connected |
Tipik Uygulamalar
OPA342UA için uygundur 6 uygulamas: High-Impedance Sensor Conditioning, Portable Measurement Systems, Low-Voltage Audio Buffers, Industrial Control Signal Paths, Battery-Powered Analog Interfaces, General-Purpose Voltage Buffering.
High-Impedance Sensor Conditioning
The OPA342UA fits high-impedance sensor conditioning because its 0.2 pA typical input bias current places very little DC load on the source. The 1 MHz gain-bandwidth product is sufficient for moderate-bandwidth amplification, while the single-supply range of 2.7 V to 5.5 V supports compact 3.3 V and 5 V systems. Place the amplifier close to the sensor connection, keep input traces short, and bias the non-inverting input within the common-mode range. This arrangement reduces leakage-induced errors that can become significant when the source impedance is high.
Önerilen
Portable Measurement Systems
The OPA342UA is useful in portable measurement systems where supply voltage and quiescent current are constrained. Its 150 µA typical quiescent current reduces the continuous load, and operation down to 2.5 V supports single-cell-compatible signal chains. The rail-to-rail input and output behavior allows more of the available supply span to be used for sensor and conversion signals. Check input offset voltage and drift against the required measurement accuracy, and ensure the selected gain remains stable at the lowest expected signal frequency.
Önerilen
Low-Voltage Audio Buffers
The OPA342UA can buffer low-voltage audio signals when rail-to-rail operation is more important than wideband performance. Its 1 MHz gain-bandwidth product covers the signal bandwidth commonly required by audio line and headphone-driver input stages, and the device operates from supplies up to 5.5 V. The CMOS input structure provides a 0.2 pA typical bias current, which is helpful when the preceding source has high impedance. Confirm distortion and noise specifications at the actual output amplitude and load before finalizing the audio path.
Önerilen
Industrial Control Signal Paths
The OPA342UA can condition low-frequency control signals in compact industrial electronics when the analog bandwidth requirement is near the 1 MHz class. Rail-to-rail input and output behavior supports operation across much of a 2.7 V to 5.5 V supply, while the low 150 µA typical quiescent current is valuable in distributed monitoring nodes. Design the feedback network for the required closed-loop gain, maintain a low-impedance ground return, and verify offset, noise, and stability over the complete industrial temperature range for the selected device grade.
Önerilen
Battery-Powered Analog Interfaces
The OPA342UA is appropriate for battery-powered analog interfaces because it supports operation as low as 2.5 V and consumes a typical 150 µA quiescent current. The low 0.2 pA input bias current also helps preserve weak sensor signals without requiring an additional bias-current buffer. Use the rail-to-rail output capability to maximize headroom, but account for output-current limits and nonlinear behavior near the rails. Confirm that shutdown requirements, if any, are handled at the system level because no dedicated shutdown function is stated for this ordering code.
Önerilen
General-Purpose Voltage Buffering
The OPA342UA works as a voltage buffer when a low-impedance output and minimal source loading are required. Follower configurations retain the amplifier's low 0.2 pA typical input bias current while presenting a substantially lower output impedance to the next circuit stage. Its 1 MHz gain-bandwidth product is appropriate for many control and sensor signals rather than high-frequency video or communications. Keep the feedback trace short, avoid long routes around the amplifier, and verify capacitive-load stability if the buffered node drives wiring, connectors, or test equipment.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: OPA342UA — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | OPA338UA |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Gain-Bandwidth Product | 1 MHz | 1 MHz class according to the available comparison |
| Special Feature | Low bias current and low-power single-supply operation | Matching primary performance profiles reported by the available comparison |
Ana Farklılayıcılar
- Very low input bias current for high-impedance signal sources (karşılaştırma:OPA338UA)
- Low-power operation for portable analog systems (karşılaştırma:OPA338UA)
- Rail-to-rail operation from a single supply (karşılaştırma:OPA338UA)
Tasarım Notları
Route the inverting input, non-inverting input, and feedback components away from high-current switching nodes and other noisy analog signals. Keep the feedback loop physically small because parasitic capacitance inside a high-gain feedback path can affect stability and peaking. Connect the supply bypass capacitor directly to pins 4 and 7 with a short ground return, and route the output separately from sensitive input nets to minimize capacitive feedthrough.
Do not leave the unused input floating. In an inverting configuration, connect the non-inverting input to a defined reference within the input common-mode range; in a non-inverting configuration, bias the inverting input through the intended feedback network. Also verify that the signal remains within the rail-to-rail operating region and account for input and output behavior near the supply limits rather than assuming ideal zero-volt saturation.
Use short, shielded or guarded routes for high-impedance sensor inputs because the 0.2 pA typical input bias current is valuable only when leakage and board contamination do not dominate. Maintain a clean guard around the input node, remove flux residue, and keep moisture away from the assembly. For capacitive loads, add an isolation resistor between the OPA342UA output and the load and confirm stability with the actual load and PCB capacitance.
Uyumluluk Bilgisi
Use the manufacturer product page and current material-compliance declarations for the OPA342UA ordering code. No specific compliance declaration was stated for the exact device.