Texas Instruments

OPA342UA - 1MHz RRIO CMOS Op Amp | Texas Instruments

MPN: OPA342UA ✓ فعال
5.5 V Vdss 0.2 pA typical Id 8-pin SOIC Package
حداقل سفارش: 1 |

OPA342UA نمای کلی

The Texas Instruments OPA342UA is a single, rail-to-rail input and output CMOS operational amplifier with a 1 MHz gain-bandwidth product, 0.2 pA typical input bias current, and a 5.5 V maximum supply voltage. It is packaged in an 8-pin SOIC and operates from low-voltage supplies beginning at 2.5 V.

An operational amplifier is a voltage-gain component used to amplify small signals, buffer high-impedance sources, perform analog calculations, and build feedback-control loops. The OPA342 belongs to the rail-to-rail operational-amplifier family, where rail-to-rail input behavior permits operation near the supply rails and rail-to-rail output behavior improves dynamic range on low-voltage systems. It is part of the broader amplifier IC and signal-conditioning product hierarchy.

Key characteristics include a 1 MHz gain-bandwidth product, 0.2 pA typical input bias current, rail-to-rail input and output operation, and a typical quiescent current of 150 µA. The input common-mode range extends 300 mV beyond the supply rails, which helps preserve input range near the rails. The 2.7 V to 5.5 V operating range supports low-voltage portable equipment, sensor interfaces, audio paths, and industrial control systems.

The CMOS design emphasizes low power and low bias current rather than high bandwidth. The manufacturer describes the OPA342 series as optimized for low-cost, low-power, miniature applications that can use a single supply. Its 1 MHz bandwidth is suitable for moderate-frequency signal conditioning, while the very low bias current is advantageous when driving high-impedance sensors or guarding against leakage errors.

Typical uses include low-power sensor conditioning, portable measurement systems, audio input stages, and general-purpose analog buffering. In a sensor interface, the low bias current limits disturbance of high-impedance sources; in an audio path, rail-to-rail input and output operation helps preserve signal range from a 2.5 V or 3.3 V supply.

Layout should keep the input and feedback paths short and provide a solid ground return. Decoupling capacitors should be placed close to the supply pins, and the unused input must be biased within the amplifier's input common-mode range. Stable operation with capacitive loads should be verified because the feedback network and output loading determine the response.

This page organizes the OPA342UA specifications, practical application guidance, compatible-device analysis, and design considerations into a buyer-focused engineering reference for selecting and implementing the device.

جایگزین‌های drop-in برای OPA342UA — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای OPA342UA (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Gain-Bandwidth Product.

Texas Instruments
Gain-Bandwidth Product: 62.5 MHz
مقایسه با OPA342UA →

OPA338UA

✅ جایگزین مستقیم
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · 5.5 V · 5.5 V · 62.5 MHz · Rail-to-rail output

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

OPA342UA حداکثر مقادیر مجاز و مشخصات الکتریکی

Amplifier Type Single operational amplifier
Technology CMOS
Gain-Bandwidth Product 1 MHz
Maximum Supply Voltage 5.5 V
ولتاژ تغذیه کاری 2.7 V to 5.5 V
Minimum Single-Supply Operation 2.5 V
Input Bias Current 0.2 pA typical
جریان سکون 150 µA typical
Input Common-Mode Range Extends 300 mV beyond the supply rails
Input Common-Mode Operation Rail-to-rail
Output Swing Rail-to-rail
Number of Channels 1 channel
بسته‌بندی 8-pin SOIC
نوع نصب Surface mount
Application Category General-purpose instrumentation amplifier

پیکربندی پین OPA342UA

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 NC — Not connected
پین 2 IN- — Inverting input
پین 3 IN+ — Non-inverting input
پین 4 V- — Negative supply connection
پین 5 NC — Not connected
پین 6 OUT — Output
پین 7 V+ — Positive supply connection
پین 8 NC — Not connected

کاربردهای معمول

OPA342UA مناسب است برای 6 کاربردs: High-Impedance Sensor Conditioning, Portable Measurement Systems, Low-Voltage Audio Buffers, Industrial Control Signal Paths, Battery-Powered Analog Interfaces, General-Purpose Voltage Buffering.

🧩

High-Impedance Sensor Conditioning

The OPA342UA fits high-impedance sensor conditioning because its 0.2 pA typical input bias current places very little DC load on the source. The 1 MHz gain-bandwidth product is sufficient for moderate-bandwidth amplification, while the single-supply range of 2.7 V to 5.5 V supports compact 3.3 V and 5 V systems. Place the amplifier close to the sensor connection, keep input traces short, and bias the non-inverting input within the common-mode range. This arrangement reduces leakage-induced errors that can become significant when the source impedance is high.

📱

Portable Measurement Systems

The OPA342UA is useful in portable measurement systems where supply voltage and quiescent current are constrained. Its 150 µA typical quiescent current reduces the continuous load, and operation down to 2.5 V supports single-cell-compatible signal chains. The rail-to-rail input and output behavior allows more of the available supply span to be used for sensor and conversion signals. Check input offset voltage and drift against the required measurement accuracy, and ensure the selected gain remains stable at the lowest expected signal frequency.

🎧

Low-Voltage Audio Buffers

The OPA342UA can buffer low-voltage audio signals when rail-to-rail operation is more important than wideband performance. Its 1 MHz gain-bandwidth product covers the signal bandwidth commonly required by audio line and headphone-driver input stages, and the device operates from supplies up to 5.5 V. The CMOS input structure provides a 0.2 pA typical bias current, which is helpful when the preceding source has high impedance. Confirm distortion and noise specifications at the actual output amplitude and load before finalizing the audio path.

🏭

Industrial Control Signal Paths

The OPA342UA can condition low-frequency control signals in compact industrial electronics when the analog bandwidth requirement is near the 1 MHz class. Rail-to-rail input and output behavior supports operation across much of a 2.7 V to 5.5 V supply, while the low 150 µA typical quiescent current is valuable in distributed monitoring nodes. Design the feedback network for the required closed-loop gain, maintain a low-impedance ground return, and verify offset, noise, and stability over the complete industrial temperature range for the selected device grade.

⚡

Battery-Powered Analog Interfaces

The OPA342UA is appropriate for battery-powered analog interfaces because it supports operation as low as 2.5 V and consumes a typical 150 µA quiescent current. The low 0.2 pA input bias current also helps preserve weak sensor signals without requiring an additional bias-current buffer. Use the rail-to-rail output capability to maximize headroom, but account for output-current limits and nonlinear behavior near the rails. Confirm that shutdown requirements, if any, are handled at the system level because no dedicated shutdown function is stated for this ordering code.

🔧

General-Purpose Voltage Buffering

The OPA342UA works as a voltage buffer when a low-impedance output and minimal source loading are required. Follower configurations retain the amplifier's low 0.2 pA typical input bias current while presenting a substantially lower output impedance to the next circuit stage. Its 1 MHz gain-bandwidth product is appropriate for many control and sensor signals rather than high-frequency video or communications. Keep the feedback trace short, avoid long routes around the amplifier, and verify capacitive-load stability if the buffered node drives wiring, connectors, or test equipment.

What is the operating voltage of OPA342UA?
The OPA342UA operates from 2.7 V to 5.5 V and is designed to operate on a single supply as low as 2.5 V. According to the Texas Instruments OPA342 datasheet, its rail-to-rail input common-mode range extends 300 mV beyond the supply rails, giving designers additional usable input range near the rail limits. The device is therefore suitable for 2.5 V, 3.3 V, and 5 V systems, subject to the detailed conditions associated with each operating point.
What are the key specifications of OPA342UA?
The OPA342UA is a single 1 MHz, rail-to-rail CMOS operational amplifier with 0.2 pA typical input bias current and a typical quiescent current of 150 µA. It operates from 2.7 V to 5.5 V, supports single-supply operation down to 2.5 V, and is available in an 8-pin SOIC package. These characteristics emphasize low power and low leakage rather than high-speed signal processing. The Texas Instruments product page identifies the device as a MicroAmplifier for low-cost and low-power applications.
Where can I download the OPA342UA datasheet PDF?
The official OPA342UA datasheet PDF is available from Texas Instruments through the OPA342 product page and the linked datasheet path. The manufacturer datasheet is the appropriate document for pin assignments, electrical characteristics, typical performance curves, recommended operating conditions, and package drawings. When designing the circuit, use the manufacturer's pin-description table to assign the 8-SOIC leads and confirm the input, output, supply, and no-connect locations before PCB routing.
Where can I find the OPA342UA pinout?
The OPA342UA pinout is shown in the Texas Instruments OPA342 datasheet and corresponds to the 8-pin SOIC arrangement. The device is a single amplifier, so pins 2 and 3 are the inverting and non-inverting inputs, pin 6 is the output, pin 4 is the negative supply, and pin 7 is the positive supply. The remaining positions are marked NC in the standard single-amplifier 8-SOIC layout. Verify the pin table before fabrication because exposed package and lead details must match the selected ordering code.
Is OPA342UA suitable for low-voltage sensor interfaces?
Yes, the OPA342UA is well suited to low-voltage sensor interfaces because its 0.2 pA typical input bias current minimizes loading on high-impedance sources. The amplifier also supports single-supply operation from 2.5 V and combines rail-to-rail input and output behavior with a 150 µA typical quiescent current. According to the Texas Instruments OPA342 datasheet, the input common-mode range extends 300 mV beyond the rails, which helps support sensor outputs near the supply limits.
What can replace OPA342UA?
OPA338UA is the closest documented single-channel SOIC alternative identified for the OPA342UA, with a comparison listing that reports identical primary performance parameters. Before using it as a replacement, verify the exact supply range, input bias current, output swing, offset, noise, stability, and temperature limits against the manufacturer datasheet for the selected grade. The OPA342UA/2K5 is a packaging representation of the same device and should not be treated as a distinct engineering alternative.
Is OPA342UA the same as OPA338UA?
OPA342UA and OPA338UA are closely related single-amplifier devices, and the available comparison identifies no measurable differences in their primary performance profiles. They should not, however, be assumed electrically identical without checking the ordering codes, package details, temperature grades, and every datasheet limit used by the design. OPA338UA is the relevant alternate for footprint and performance evaluation; final substitution approval should include stability, bias-current, offset-voltage, and supply-voltage checks.
OPA342UA vs OPA338UA: which is better for a portable sensor circuit?
OPA338UA is the more practical candidate to evaluate first for a portable sensor circuit because it shares the same documented 1 MHz class of operation and is presented as a close alternative with matching primary performance characteristics. OPA342UA remains the defined target for this design. The final choice should consider total supply current, leakage, offset voltage, noise, temperature grade, and input/output range, especially if the sensor source impedance is high or battery life dominates the design.
When should I choose OPA342UA over OPA338UA?
Choose OPA342UA when the design has already been qualified around its 0.2 pA typical input bias current, 150 µA typical quiescent current, 1 MHz gain-bandwidth product, and 2.7 V to 5.5 V supply range. Consider OPA338UA when its manufacturer documentation confirms equal or better performance for the selected grade. For either device, validate offset drift, noise, capacitive-load stability, and output drive in the final circuit because headline bandwidth and bias-current values do not describe every application-specific requirement.
Is OPA342UA suitable for audio signal conditioning?
The OPA342UA can be used for low-voltage audio signal conditioning because it provides rail-to-rail input and output operation from a single supply. Its 1 MHz gain-bandwidth product is appropriate for many audio-frequency buffers and preamplifier stages, while the 150 µA typical quiescent current supports power-conscious designs. A low-noise audio application should also confirm the input noise density, output distortion, channel-to-channel offset, and stable operation with the intended source impedance and load.
What is the best drop-in replacement for OPA342UA?
OPA338UA is the best documented drop-in candidate for the OPA342UA because it uses the same single-amplifier SOIC format and the available comparison reports no measurable differences in the primary technical parameters. Confirm the exact 8-pin SOIC footprint, pin arrangement, supply limits, electrical limits, and temperature grade in the manufacturer documentation before production use. No additional cross-brand MPNs could be verified from the available cross-reference material, so unverified equivalents should not be treated as drop-in replacements.
What is the best Analog Devices equivalent for OPA342UA?
The available OPA342 cross-reference results identify Analog Devices as a possible replacement manufacturer but do not provide a specific Analog Devices MPN with verified package and pin compatibility. A named Analog Devices equivalent therefore cannot be confirmed as a drop-in replacement from the available documentation. Enter the OPA342UA requirements into the manufacturer's cross-reference tool, then compare package, pinout, supply voltage, bandwidth, bias current, offset, noise, and stability before approving a substitute.
Where to buy OPA342UA online?
Use the Request a Quote form on this page to request OPA342UA pricing, availability, and order handling from XAIPART. The request can specify the required quantity, packaging preference, and target delivery schedule. Because availability and commercial terms can change, request an updated quotation rather than relying on a static listing. The manufacturer product page and official datasheet links on this page remain the appropriate references for technical selection.
What is the price of OPA342UA?
Use the Request a Quote form on this page for the current OPA342UA unit price and quantity pricing. Pricing depends on order quantity, packaging, component condition, and current supply, so a current quotation is more appropriate than a static figure. The OPA342UA ordering code is the important selection reference; request confirmation that the quotation covers the exact 8-pin SOIC package and the quantity required for your production schedule.
What is the lead time for OPA342UA?
Request the current OPA342UA lead time through the Request a Quote form on this page. Lead time can vary with order quantity, packaging, inventory position, and manufacturing conditions. Include your required delivery date and target annual usage so the commercial response can reflect the intended procurement plan. The exact MPN, OPA342UA, should appear on the request and resulting quotation to prevent confusion with other package or temperature-grade options.

داده‌های مرجع مهندسی برای OPA342UA — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose OPA342UA when a single-supply, low-power amplifier is needed with a 1 MHz gain-bandwidth product, 0.2 pA typical input bias current, and rail-to-rail input and output behavior. It is particularly suitable for high-impedance sensor signals, portable measurement circuits, audio buffering, and low-voltage control systems. OPA338UA is the closest documented alternative and should be considered when its exact manufacturer limits match or improve the required offset, noise, supply range, temperature grade, and stability. The OPA342UA/2K5 and OPA342UAG4 are ordering representations of the target family and are not treated as distinct engineering alternatives. For any proposed substitute, verify the 8-SOIC footprint, pin assignment, maximum supply voltage, input common-mode range, output swing, offset drift, noise, and capacitive-load behavior before releasing a production design.

مقایسه با جایگزین‌ها

پارامتر این محصول OPA338UA
Package 8-pin SOIC 8-pin SOIC
Brand Texas Instruments Texas Instruments
Gain-Bandwidth Product 1 MHz 1 MHz class according to the available comparison
Special Feature Low bias current and low-power single-supply operation Matching primary performance profiles reported by the available comparison

تفاوت‌های کلیدی

  • Very low input bias current for high-impedance signal sources (در مقابلOPA338UA)
  • Low-power operation for portable analog systems (در مقابلOPA338UA)
  • Rail-to-rail operation from a single supply (در مقابلOPA338UA)

یادداشت‌های طراحی

Route the inverting input, non-inverting input, and feedback components away from high-current switching nodes and other noisy analog signals. Keep the feedback loop physically small because parasitic capacitance inside a high-gain feedback path can affect stability and peaking. Connect the supply bypass capacitor directly to pins 4 and 7 with a short ground return, and route the output separately from sensitive input nets to minimize capacitive feedthrough.

Do not leave the unused input floating. In an inverting configuration, connect the non-inverting input to a defined reference within the input common-mode range; in a non-inverting configuration, bias the inverting input through the intended feedback network. Also verify that the signal remains within the rail-to-rail operating region and account for input and output behavior near the supply limits rather than assuming ideal zero-volt saturation.

Use short, shielded or guarded routes for high-impedance sensor inputs because the 0.2 pA typical input bias current is valuable only when leakage and board contamination do not dominate. Maintain a clean guard around the input node, remove flux residue, and keep moisture away from the assembly. For capacitive loads, add an isolation resistor between the OPA342UA output and the load and confirm stability with the actual load and PCB capacitance.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

Use the manufacturer product page and current material-compliance declarations for the OPA342UA ordering code. No specific compliance declaration was stated for the exact device.

تاریخ تأیید داده‌ها: 2026-11-19 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

OPA342UA datasheet OPA342UA pinout OPA342UA datasheet pdf OPA342UA equivalent OPA342UA replacement OPA342UA vs OPA338UA OPA342UA SOIC-8 amplifier OPA342UA 1MHz op amp OPA342UA 0.2pA bias current OPA342UA price Texas Instruments OPA342UA OPA342 sensor interface

قطعات و اصطلاحات مرتبط

Texas Instruments OPA342UA OPA342 OPA338UA OPA2342 OPA4342 OPA137P operational amplifier CMOS operational amplifier rail-to-rail input rail-to-rail output MicroAmplifier 8-pin SOIC SOIC family surface-mount package gain-bandwidth product input bias current quiescent current common-mode voltage range signal conditioning high-impedance sensor audio buffer industrial control battery-powered interface
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ