PCA9507D - 400kHz 2-Wire I2C Bus Extender | NXP
MPN: PCA9507D ✓ AktifPCA9507D Genel Bakış
An I2C bus extender is an interface IC that preserves two-wire serial communication across a physical distance or voltage boundary. The PCA9507D belongs to the I2C interface-controller and signal-buffer hierarchy: it supports the I2C-bus system while providing bidirectional buffering for both SDA and SCL. Its dual-supply architecture lets the two sides of the bus operate at different logic levels, making the device useful when a downstream circuit uses a voltage outside the source-side range.
The primary features include 3.3 V to 5 V level shifting, operation up to 400 kHz, and bus extension to 18 meters. Bidirectional buffering is important because I2C and SMBus use open-drain signaling in which pull-up resistors, rather than the active driver, establish the high state. The PCA9507D accommodates that topology without changing the basic operating modes of the two-wire bus.
Technically, the device separates the source-side and destination-side signal paths while preserving clock and data behavior. This arrangement can maintain communication between circuit boards or cable-linked equipment where direct capacitance, voltage incompatibility, or bus-length limitations would otherwise degrade signal integrity. Its 400 kHz frequency class supports moderate-speed control, configuration, and status buses rather than high-bandwidth data transfer.
Typical applications include extending HDMI Display Data Channel connections between a source and display, isolating I2C control lines across equipment boundaries, lengthening SMBus communication paths, and adapting 3.3 V logic to a 5 V peripheral. The SOIC-8 package also supports conventional surface-mount assembly and compact two-sided PCB layouts.
Designers should use the pin-description and application diagrams in the NXP manufacturer datasheet when assigning pull-up resistors, supply connections, and signal routing. Place the device near the physical midpoint of a long extension rather than at only one end, because its intended benefit depends on buffering the two bus segments and isolating their loading. Confirm that both bus speeds, voltage domains, rise times, and pull-up arrangements meet the device and system requirements.
This page combines the manufacturer’s bus-extension capabilities with practical placement guidance, sourcing paths, and verified drop-in alternatives. It is intended to help engineers determine whether the PCA9507D solves the specific level-shifting, distance, or loading constraint in an I2C, SMBus, or HDMI DDC design.
Drop-in alternatifler için PCA9507D — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller PCA9507D (aynı form faktörü ve ayağa oturma) — farklı olan Package.
PCA9507D,112
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
PCA9507DP,118
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PCA9507D,118
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
PCA9507D Özellikler
| Product Type | 2-wire serial bus extender |
| Supported Buses | I2C, SMBus, HDMI DDC |
| Maximum Bus Frequency | 400 kHz |
| Logic Level Shift Range | 3.3 V to 5 V |
| Maximum Bus Extension | 18 m |
| Channel Count | 1 channel |
| Signal Type | Bidirectional SDA and SCL buffering |
| Supply Architecture | Dual supply |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
| Manufacturer Order Code | PCA9507D,118 |
| Yaşam Döngüsü Durumu | Active |
| RoHS Compliance | Compliant |
| REACH Compliance | Compliant |
| Conflict-Free Status | DRC Conflict Free |
PCA9507D 8-pin soic Pin Yapısı Kılavuzu
PCA9507D (8-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: PCA9507D.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
PCA9507D için uygundur 6 uygulamas: HDMI Display Data Channel Extension, I2C Level Translation Between 3.3 V and 5 V, SMBus Control-Link Isolation, Board-to-Board I2C Cabling, Display and Monitor Configuration Bus, Remote Sensor and Actuator Bus.
HDMI Display Data Channel Extension
The PCA9507D fits between an HDMI source and display when their DDC SDA and SCL lines require greater reach or different logic levels. Its 3.3 V to 5 V bidirectional level shifting addresses voltage-domain differences, while the 400 kHz bus rating accommodates the relatively slow DDC control traffic. The manufacturer specifies extension capability up to 18 meters for reliable HDMI DDC, I2C, and SMBus operation. Place the extender near the cable transition so each PCB section presents a separate, buffered bus segment. Validate pull-up placement, capacitance, and signal rise time in the complete source-to-display link because connector and cable parasitics can influence the achievable distance.
Önerilen
I2C Level Translation Between 3.3 V and 5 V
The PCA9507D is useful when a 3.3 V controller must communicate with a 5 V I2C peripheral through board-level wiring. Its 3.3 V to 5 V level-shift function and bidirectional SDA/SCL buffering allow each side to retain an appropriate local logic domain. The 400 kHz operating frequency covers common control, configuration, and sensor buses without requiring a high-speed transceiver. Select separate pull-up networks for the two voltage domains and keep the extender positioned near the voltage-domain transition. The manufacturer supports bus extension to 18 meters, but practical distance still depends on cable construction, pull-up strength, clock rate, and the rise-time requirements of both endpoint devices.
Önerilen
SMBus Control-Link Isolation
PCA9507D can extend and level-shift an SMBus management link between equipment cards, rack modules, or remote sensor assemblies. SMBus uses the same bidirectional clock-and-data signaling style as I2C, allowing the PCA9507D to buffer both SDA and SCL while preserving normal bus operation. Its 400 kHz maximum frequency is appropriate for configuration, identification, monitoring, and supervisory-control traffic rather than bulk data. The dual-supply capability supports a source-side and destination-side voltage split, and the 18-meter extension specification provides useful design margin when structured cabling is involved. Confirm pull-up resistor values separately on each buffered side and verify that power sequencing, bus idle levels, and device address behavior remain acceptable across the complete system.
Önerilen
Board-to-Board I2C Cabling
The PCA9507D addresses long board-to-board I2C links where round-trip trace delay, connector loading, or voltage incompatibility would weaken the original bus. Its bidirectional buffering creates two distinct bus segments, allowing a controller and peripheral to communicate through a cable as long as 18 meters under the manufacturer’s stated operating conditions. The 3.3 V to 5 V level-shift range makes the same device useful in mixed-voltage equipment. For implementation, locate the extender near the board connector, place pull-up resistors on the appropriate side of each segment, and maintain a short ground-reference path between the connected assemblies. The 400 kHz limit and external pull-up network remain central constraints when establishing the final communication margin.
Önerilen
Display and Monitor Configuration Bus
The PCA9507D is appropriate for monitor, television, projector, and display-adjacent electronics that expose a slow I2C-compatible configuration or control bus. The 400 kHz rate is more than sufficient for register-based setup and status communication, while the level translator prevents a 3.3 V controller from being exposed to a 5 V bus. Bidirectional buffering also permits the bus to continue across a panel cable or internal harness where direct routing would be impractical. Use a low-capacitance connection strategy and independent pull-ups for each voltage section. The manufacturer’s 18-meter capability should not be interpreted as guaranteeing every cable or display implementation, because rise time, EMI, grounding, and endpoint capacitance determine whether the full margin is available in the finished product.
Önerilen
Remote Sensor and Actuator Bus
The PCA9507D can connect a control board to a remote I2C sensor or actuator assembly when the harness is longer than a conventional local bus supports. The 3.3 V to 5 V translation accommodates mixed supply domains, while the bidirectional buffer preserves clock and data flow in either direction. At up to 400 kHz, the interface is suitable for environmental sensors, identification devices, and low-bandwidth actuator controllers that exchange setup and status registers rather than streaming data. The 18-meter extension rating makes the device relevant to industrial cabinets and distributed equipment. Before deployment, verify the sensor’s maximum bus rate, cable capacitance, pull-up values, ground continuity, and protection requirements, and add the appropriate surge or ESD protection when the cable leaves the enclosure.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: PCA9507D — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | PCA9507D,112 | PCA9507DP,118 | PCA9507D,118 |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Function | 2-wire serial bus extender | 2-wire serial bus extender | 2-wire serial bus extender | 2-wire serial bus extender |
| Maximum Bus Frequency | 400 kHz | 400 kHz | 400 kHz | 400 kHz |
| Level Shift Range | 3.3 V to 5 V | 3.3 V to 5 V | 3.3 V to 5 V | 3.3 V to 5 V |
| Maximum Bus Extension | 18 m | 18 m | 18 m | 18 m |
| Channel Count | 1 channel | 1 channel | 1 channel | 1 channel |
| Supported Buses | I2C, SMBus, HDMI DDC | I2C, SMBus, HDMI DDC | I2C, SMBus, HDMI DDC | I2C, SMBus, HDMI DDC |
| Supply Architecture | Dual supply | Dual supply | Dual supply | Dual supply |
Ana Farklılayıcılar
- Combines bus extension and voltage translation (karşılaştırma:PCA9507D,112)
- Supports a 400 kHz two-wire interface (karşılaştırma:PCA9507DP,118)
- Bidirectional buffering preserves normal bus operation (karşılaştırma:PCA9507D,118)
Tasarım Notları
Place the PCA9507D near the physical transition between the local and remote I2C or SMBus segments. Keep the SDA and SCL routes short on each side, maintain a continuous ground reference between boards, and place the relevant pull-up resistors close to the devices that use each voltage domain. For long cables, terminate the extended bus according to the manufacturer application guidance and account for connector capacitance before increasing pull-up strength.
Use the 400 kHz operating limit as an upper design boundary and evaluate the complete bus at the intended clock rate. I2C and SMBus rise time depends on bus capacitance and pull-up resistance, so a short nominal cable does not necessarily guarantee acceptable signal quality. Check the source and destination devices for their minimum high-time and rise-time requirements, and verify both buffered segments with the final harness and pull-up values.
Provide clean supply connections to both sides of the PCA9507D because its dual-supply architecture supports level translation between different logic domains. Confirm the accepted supply range for each side from the NXP manufacturer datasheet before assigning 3.3 V or 5 V rails. Keep the ground pins connected to the system ground without placing long return-current loops between the extender and the cable termination.
Do not treat the PCA9507D as a general-purpose protocol converter or assume that the maximum 18-meter rating is independent of bus capacitance and clock rate. Also avoid replacing it solely because another IC is described as an I2C repeater. Verify the exact pin assignments, supply voltages, enable behavior, pull-up strategy, and propagation requirements from the manufacturer datasheet, especially when making a production substitution.
Uyumluluk Bilgisi
The product catalog lists EU RoHS compliance, REACH compliance, and DRC Conflict Free status. No separate lead-free, halogen-free, or automotive qualification statement was confirmed.