PCA9554N - 8-Bit I2C GPIO Expander | NXP | DIP-16
MPN: PCA9554N ✓ AktifPCA9554N Genel Bakış
An I2C GPIO expander is a peripheral interface IC that converts serial I2C or SMBus commands into parallel digital inputs and outputs. It extends the number of control and status pins available from a microcontroller or application processor while preserving the processor's limited I/O resources. The PCA9554 belongs to the interface IC hierarchy and supports address configuration, input/output direction control, port registers, and an interrupt mechanism for input-state changes.
The PCA9554N provides eight GPIO pins, three hardware address inputs, a 400 kHz I2C interface, an interrupt output, and weak internal pull-ups. Address pins A0, A1, and A2 permit multiple devices to share one bus, with the manufacturer describing support for as many as eight devices on the same I2C or SMBus bus. Each port bit can be configured independently as input or output, making the device useful for control, monitoring, and status signaling functions.
Communication with the PCA9554N uses the standard two-wire SCL and SDA signals alongside VCC and ground. The interrupt output provides a hardware indication that a change occurred on a configured input port, allowing the host to respond without continuously polling all eight inputs. Weak internal pull-ups assist with open-drain bus signaling but are intended mainly for lightly loaded conditions; external pull-up resistors should be selected according to bus voltage, capacitance, and clock rate.
Typical applications include industrial control panels, sensor interfaces, relay and LED monitoring, configuration port expansion, battery-powered instrumentation, and embedded systems requiring more GPIO than the host controller provides. The 2.3 V to 5.5 V operating range permits use with both 3.3 V and 5 V systems, while the DIP-16 mechanical format is convenient for prototyping, through-hole assembly, and manually reworkable laboratory boards.
PCB design should preserve the standard DIP-16 footprint with 2.54 mm pitch and place decoupling close to VCC and ground. Confirm that every I2C node uses a unique address combination and that pull-up resistance satisfies the bus rise-time requirements at the intended 400 kHz maximum operating rate. Firmware must also configure each port direction correctly before treating a pin as an output.
This product page combines manufacturer package information, interface capabilities, source-referenced alternatives, comparison parameters, and practical implementation guidance. It is intended to help engineers assess GPIO capacity, bus compatibility, package reuse, and firmware requirements before selecting a replacement or integrating the device into a new design.
Drop-in alternatifler için PCA9554N — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller PCA9554N (aynı form faktörü ve ayağa oturma) — farklı olan Interrupt Output, Package Type, RoHS Status.
PCA9554ABS3,118
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PCA9554ABS3,118
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PCA9554ABS3,118
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PCF8574AT/3,518
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PCF8574AT/3,518
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PCA9554N Özellikler
| Product Type | 8-bit I2C/SMBus GPIO expander |
| Number of GPIO Pins | 8 pins |
| Operating Supply Voltage Range | 2.3 V to 5.5 V |
| Maximum I2C Bus Frequency | 400 kHz |
| Supported Serial Protocols | I2C and SMBus |
| Interrupt Output | 1 active-low open-drain interrupt output |
| Internal Pull-Up Resistors | Weak internal pull-ups |
| Hardware Address Inputs | 3 inputs, A0, A1, and A2 |
| Maximum Devices per Bus | 8 devices |
| Package Type | DIP-16 plastic dual in-line package |
| Number of Leads | 16 leads |
| Lead Pitch | 2.54 mm |
| Package Body Dimensions | 19 mm × 6.35 mm × 4.2 mm |
| Montaj Stili | Through-hole |
| Logic Families Supported | CMOS |
| Device Architecture | 8-bit general-purpose parallel input/output expander |
PCA9554N Pin Yapısı
| Pin 1 | A0 — Hardware address input A0 |
| Pin 2 | A1 — Hardware address input A1 |
| Pin 3 | A2 — Hardware address input A2 |
| Pin 4 | SCL — Serial clock input |
| Pin 5 | SDA — Serial data input/output |
| Pin 6 | P0 — General-purpose input/output port 0 |
| Pin 7 | P1 — General-purpose input/output port 1 |
| Pin 8 | P2 — General-purpose input/output port 2 |
| Pin 9 | P3 — General-purpose input/output port 3 |
| Pin 10 | GND — Ground connection |
| Pin 11 | P4 — General-purpose input/output port 4 |
| Pin 12 | P5 — General-purpose input/output port 5 |
| Pin 13 | P6 — General-purpose input/output port 6 |
| Pin 14 | P7 — General-purpose input/output port 7 |
| Pin 15 | INT — Interrupt output |
| Pin 16 | VCC — Positive supply voltage |
Tipik Uygulamalar
PCA9554N için uygundur 6 uygulamas: Industrial Control Panel Expansion, Embedded Sensor Interface, LED and Relay Status Control, Battery-Powered Instrumentation, Server and Storage Configuration Port, Communication Equipment Status Port.
Industrial Control Panel Expansion
The PCA9554N is well suited to industrial control panels because eight configurable GPIO lines can operate panel indicators, discrete commands, status lamps, or interlock-related inputs while the controller communicates through I2C. Its 2.3 V to 5.5 V range supports common 3.3 V and 5 V control electronics, and the interrupt output can notify the controller when an input changes. Use the three address inputs to assign an appropriate bus address, configure directions in firmware, and select external I2C pull-ups for the panel cable and 400 kHz operating rate.
Önerilen
Embedded Sensor Interface
The PCA9554N can consolidate discrete sensor-enable, alarm, fault, and ready signals into a controlled I2C peripheral. Eight inputs reduce the host's direct GPIO burden, while eight outputs can drive sensor reset, enable, or operating-mode controls. Its 400 kHz bus rate is sufficient for typical low-bandwidth status polling. Configure inputs before enabling interrupt handling, account for the device's weak internal pull-ups, and add external pull-ups where longer wiring or bus capacitance requires faster rising edges.
Önerilen
LED and Relay Status Control
The PCA9554N provides a practical way to operate small LED indicators or relay-control and status lines where the host controller has limited direct outputs. The I2C interface reduces wiring compared with eight dedicated GPIO pins, and the port can mix configured inputs and outputs for acknowledgment or fault signals. Its 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V logic systems. Keep inductive loads and high-current LED drivers properly isolated or use suitable external transistors, because the PCA9554N is a logic interface rather than a power-driver device.
Önerilen
Battery-Powered Instrumentation
The PCA9554N can add monitoring and configuration lines to compact battery-powered instruments without consuming the host controller's direct GPIO pins. The device operates from 2.3 V to 5.5 V, and the interrupt output allows the host to avoid continuous polling of slowly changing inputs such as mode selectors, charger status, or service buttons. Low-leakage design practice should be reviewed for battery applications, while weak internal pull-ups may be useful for lightly loaded inputs but should not substitute for bus pull-ups intended to support a 400 kHz, multi-device network.
Önerilen
Server and Storage Configuration Port
The PCA9554N can serve as a compact configuration and fault-monitoring peripheral in server, storage, or networking equipment. Eight outputs can represent control commands, while eight inputs can collect reset, fault, presence, or enclosure signals through the I2C bus. The 400 kHz interface and hardware-address inputs allow several expanders to share a control bus when the board requires more status points. Firmware must avoid unnecessary polling through the interrupt mechanism, and the layout should keep the I2C route away from high-speed switching and noisy power-conversion regions.
Önerilen
Communication Equipment Status Port
The PCA9554N is useful in communication equipment that needs additional front-panel, backplane, or module-status signals without dedicating host-controller pins. The interrupt output can signal a change in link, reset, alarm, or service inputs, while outputs can control local enable or mute functions. Its 2.3 V to 5.5 V range supports mixed legacy and modern logic environments, provided every connected interface uses compatible levels. Maintain short I2C routing, use suitable pull-up resistance, and verify that the selected DIP footprint leaves adequate spacing for through-hole assembly and service access.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: PCA9554N — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | PCA9554A | PCA9554 | PCA9554A | PCF8574 | PCF8574A |
|---|---|---|---|---|---|---|
| Package | DIP-16 | DIP-16 | DIP-16 | DIP-16 | DIP-16 | DIP-16 |
| Brand | NXP Semiconductors | NXP Semiconductors | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors |
| GPIO Count | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Address Configuration | A0, A1, and A2 hardware inputs | Different PCA9554-family address | A0, A1, and A2 hardware inputs | Different PCA9554-family address | Compatible address arrangement | Different PCF8574-family address |
| Software Compatibility | PCA9554 register model | PCA9554A register model with different address | PCA9554 register model | PCA9554A register model with different address | Software changes required | Software changes required |
Ana Farklılayıcılar
- Provides a genuine DIP-16 footprint rather than requiring an SMT-only conversion (karşılaştırma:PCA9554A)
- Combines eight GPIO lines with a dedicated interrupt output (karşılaştırma:PCF8574)
- Supports eight bus address combinations through three hardware inputs (karşılaştırma:PCA9554A)
- Operates across common embedded logic-voltage rails (karşılaştırma:PCF8574A)
Tasarım Notları
Place the decoupling capacitor as close as practical to the PCA9554N VCC and ground pins, and route SCL and SDA away from switching nodes and high-current return paths. The DIP-16 footprint uses a 2.54 mm pitch. Keep address-input traces short and deliberate because A0, A1, and A2 determine the device's bus address. If multiple expanders are installed, label the address straps clearly to reduce configuration errors.
The internal pull-ups are weak and should not be assumed to provide adequate bus rise time at 400 kHz. Determine total bus capacitance and select external pull-up resistance for the actual bus voltage, trace length, number of nodes, and clock rate. Verify the resulting rise and fall times with an oscilloscope on the assembled board, particularly when the harness is long or several expanders share the bus.
Do not assume that a PCA9554N is a register-for-register PCF8574 replacement. TI identifies pin-to-pin and I2C-address compatibility with PCF8574 but also states that software changes are required for PCA9554's enhancements. Review direction-control, input/output polarity, interrupt, and initialization behavior in firmware. When changing to PCA9554A, update the addressed device and verify that the new address does not conflict with another peripheral.
The PCA9554N is a logic interface and is not intended to drive relays, high-current LEDs, or other power loads directly. Use suitable transistors, buffer drivers, or protection circuits for those loads. Define the output-pin current limits and total supply current from the manufacturer datasheet, account for simultaneous output activity, and size VCC decoupling so switching loads do not create unacceptable rail transients.
Uyumluluk Bilgisi
Compliance attributes require confirmation from the current manufacturer product documentation or applicable declaration.