NXP Semiconductors

PCA9554N - 8-Bit I2C GPIO Expander | NXP | DIP-16

MPN: PCA9554N ✓ فعال
2.3 V to 5.5 V Vdss DIP-16 plastic dual in-line package Package 400 kHz Speed
MOQ: 1 |

PCA9554N جائزہ

NXP Semiconductors PCA9554N is an 8-bit I2C-bus and SMBus general-purpose input/output expander with interrupt output, weak internal pull-up resistors, and operation from 2.3 V to 5.5 V. The device is packaged in a 16-lead plastic dual in-line package with a 2.54 mm lead pitch and a 19 mm × 6.35 mm × 4.2 mm body. It adds eight configurable GPIO lines to a host processor through a two-wire serial bus.

An I2C GPIO expander is a peripheral interface IC that converts serial I2C or SMBus commands into parallel digital inputs and outputs. It extends the number of control and status pins available from a microcontroller or application processor while preserving the processor's limited I/O resources. The PCA9554 belongs to the interface IC hierarchy and supports address configuration, input/output direction control, port registers, and an interrupt mechanism for input-state changes.

The PCA9554N provides eight GPIO pins, three hardware address inputs, a 400 kHz I2C interface, an interrupt output, and weak internal pull-ups. Address pins A0, A1, and A2 permit multiple devices to share one bus, with the manufacturer describing support for as many as eight devices on the same I2C or SMBus bus. Each port bit can be configured independently as input or output, making the device useful for control, monitoring, and status signaling functions.

Communication with the PCA9554N uses the standard two-wire SCL and SDA signals alongside VCC and ground. The interrupt output provides a hardware indication that a change occurred on a configured input port, allowing the host to respond without continuously polling all eight inputs. Weak internal pull-ups assist with open-drain bus signaling but are intended mainly for lightly loaded conditions; external pull-up resistors should be selected according to bus voltage, capacitance, and clock rate.

Typical applications include industrial control panels, sensor interfaces, relay and LED monitoring, configuration port expansion, battery-powered instrumentation, and embedded systems requiring more GPIO than the host controller provides. The 2.3 V to 5.5 V operating range permits use with both 3.3 V and 5 V systems, while the DIP-16 mechanical format is convenient for prototyping, through-hole assembly, and manually reworkable laboratory boards.

PCB design should preserve the standard DIP-16 footprint with 2.54 mm pitch and place decoupling close to VCC and ground. Confirm that every I2C node uses a unique address combination and that pull-up resistance satisfies the bus rise-time requirements at the intended 400 kHz maximum operating rate. Firmware must also configure each port direction correctly before treating a pin as an output.

This product page combines manufacturer package information, interface capabilities, source-referenced alternatives, comparison parameters, and practical implementation guidance. It is intended to help engineers assess GPIO capacity, bus compatibility, package reuse, and firmware requirements before selecting a replacement or integrating the device into a new design.

کے لیے ڈراپ اِن متبادل PCA9554N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PCA9554N (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Interrupt Output, Package Type, RoHS Status.

NXP Semiconductors
Interrupt Output: /INT, open-drain
RoHS Status: Compliant
موازنہ کریں PCA9554N →
NXP Semiconductors
Interrupt Output: Yes, active-low INT pin (open-drain)
Package Type: SOIC-16 (MS-013 / SOT-162-1), 7.50 mm body, lead-free
RoHS Status: Compliant (lead-free)

PCA9554ABS3,118

✅ ڈراپ-اِن
NXP Semiconductors
📦 DIP-16
I2C, SMBus · 8 · 400 kHz · 2.3 V to 5.5 V · 5.5 V · 3 hardware address pins (up to 8 devices) · /INT, open-drain · 0x38 (3-bit addr 000 = 0x38)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

PCA9554ABS3,118

✅ ڈراپ-اِن
NXP Semiconductors
📦 DIP-16
I2C, SMBus · 8 · 400 kHz · 2.3 V to 5.5 V · 5.5 V · 3 hardware address pins (up to 8 devices) · /INT, open-drain · 0x38 (3-bit addr 000 = 0x38)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

PCA9554ABS3,118

✅ ڈراپ-اِن
NXP Semiconductors
📦 DIP-16
I2C, SMBus · 8 · 400 kHz · 2.3 V to 5.5 V · 5.5 V · 3 hardware address pins (up to 8 devices) · /INT, open-drain · 0x38 (3-bit addr 000 = 0x38)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

PCF8574AT/3,518

✅ ڈراپ-اِن
NXP Semiconductors
📦 DIP-16
PCF8574AT/3,518 · 8-bit I/O Expander with I2C-bus interface · 8 · I2C (SCL/SDA), 2-wire serial · 100 kHz · 2.5 V to 6 V · 0x38-0x3F (PCF8574A family: 0x38-0x3F) · Quasi-bidirectional (weak pull-up current source)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

PCF8574AT/3,518

✅ ڈراپ-اِن
NXP Semiconductors
📦 DIP-16
PCF8574AT/3,518 · 8-bit I/O Expander with I2C-bus interface · 8 · I2C (SCL/SDA), 2-wire serial · 100 kHz · 2.5 V to 6 V · 0x38-0x3F (PCF8574A family: 0x38-0x3F) · Quasi-bidirectional (weak pull-up current source)

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

PCA9554N تفصیلات

Product Type 8-bit I2C/SMBus GPIO expander
Number of GPIO Pins 8 pins
Operating Supply Voltage Range 2.3 V to 5.5 V
Maximum I2C Bus Frequency 400 kHz
Supported Serial Protocols I2C and SMBus
Interrupt Output 1 active-low open-drain interrupt output
Internal Pull-Up Resistors Weak internal pull-ups
Hardware Address Inputs 3 inputs, A0, A1, and A2
Maximum Devices per Bus 8 devices
Package Type DIP-16 plastic dual in-line package
Number of Leads 16 leads
Lead Pitch 2.54 mm
Package Body Dimensions 19 mm × 6.35 mm × 4.2 mm
ماؤنٹنگ اسٹائل Through-hole
Logic Families Supported CMOS
Device Architecture 8-bit general-purpose parallel input/output expander

PCA9554N پن کنفیگریشن

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
پن 1 A0 — Hardware address input A0
پن 2 A1 — Hardware address input A1
پن 3 A2 — Hardware address input A2
پن 4 SCL — Serial clock input
پن 5 SDA — Serial data input/output
پن 6 P0 — General-purpose input/output port 0
پن 7 P1 — General-purpose input/output port 1
پن 8 P2 — General-purpose input/output port 2
پن 9 P3 — General-purpose input/output port 3
پن 10 GND — Ground connection
پن 11 P4 — General-purpose input/output port 4
پن 12 P5 — General-purpose input/output port 5
پن 13 P6 — General-purpose input/output port 6
پن 14 P7 — General-purpose input/output port 7
پن 15 INT — Interrupt output
پن 16 VCC — Positive supply voltage

عام استعمالات

PCA9554N کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Panel Expansion, Embedded Sensor Interface, LED and Relay Status Control, Battery-Powered Instrumentation, Server and Storage Configuration Port, Communication Equipment Status Port.

🏭

Industrial Control Panel Expansion

The PCA9554N is well suited to industrial control panels because eight configurable GPIO lines can operate panel indicators, discrete commands, status lamps, or interlock-related inputs while the controller communicates through I2C. Its 2.3 V to 5.5 V range supports common 3.3 V and 5 V control electronics, and the interrupt output can notify the controller when an input changes. Use the three address inputs to assign an appropriate bus address, configure directions in firmware, and select external I2C pull-ups for the panel cable and 400 kHz operating rate.

🧩

Embedded Sensor Interface

The PCA9554N can consolidate discrete sensor-enable, alarm, fault, and ready signals into a controlled I2C peripheral. Eight inputs reduce the host's direct GPIO burden, while eight outputs can drive sensor reset, enable, or operating-mode controls. Its 400 kHz bus rate is sufficient for typical low-bandwidth status polling. Configure inputs before enabling interrupt handling, account for the device's weak internal pull-ups, and add external pull-ups where longer wiring or bus capacitance requires faster rising edges.

💡

LED and Relay Status Control

The PCA9554N provides a practical way to operate small LED indicators or relay-control and status lines where the host controller has limited direct outputs. The I2C interface reduces wiring compared with eight dedicated GPIO pins, and the port can mix configured inputs and outputs for acknowledgment or fault signals. Its 2.3 V to 5.5 V supply range supports both 3.3 V and 5 V logic systems. Keep inductive loads and high-current LED drivers properly isolated or use suitable external transistors, because the PCA9554N is a logic interface rather than a power-driver device.

🔧

Battery-Powered Instrumentation

The PCA9554N can add monitoring and configuration lines to compact battery-powered instruments without consuming the host controller's direct GPIO pins. The device operates from 2.3 V to 5.5 V, and the interrupt output allows the host to avoid continuous polling of slowly changing inputs such as mode selectors, charger status, or service buttons. Low-leakage design practice should be reviewed for battery applications, while weak internal pull-ups may be useful for lightly loaded inputs but should not substitute for bus pull-ups intended to support a 400 kHz, multi-device network.

🖥️

Server and Storage Configuration Port

The PCA9554N can serve as a compact configuration and fault-monitoring peripheral in server, storage, or networking equipment. Eight outputs can represent control commands, while eight inputs can collect reset, fault, presence, or enclosure signals through the I2C bus. The 400 kHz interface and hardware-address inputs allow several expanders to share a control bus when the board requires more status points. Firmware must avoid unnecessary polling through the interrupt mechanism, and the layout should keep the I2C route away from high-speed switching and noisy power-conversion regions.

🌐

Communication Equipment Status Port

The PCA9554N is useful in communication equipment that needs additional front-panel, backplane, or module-status signals without dedicating host-controller pins. The interrupt output can signal a change in link, reset, alarm, or service inputs, while outputs can control local enable or mute functions. Its 2.3 V to 5.5 V range supports mixed legacy and modern logic environments, provided every connected interface uses compatible levels. Maintain short I2C routing, use suitable pull-up resistance, and verify that the selected DIP footprint leaves adequate spacing for through-hole assembly and service access.

What is the PCA9554N?
The PCA9554N is an 8-bit I2C and SMBus GPIO expander that adds eight configurable parallel input/output pins to a host processor. According to the NXP PCA9554 product information, it includes an interrupt output and weak internal pull-up resistors, operates from 2.3 V to 5.5 V, and is available in a 16-lead DIP package. It is useful when a microcontroller, application processor, or industrial controller has insufficient GPIO pins for external controls and status signals.
What is the operating voltage of PCA9554N?
The PCA9554N operates from 2.3 V to 5.5 V, allowing it to interface with both 3.3 V and 5 V systems. NXP identifies the part as an 8-bit I2C-bus and SMBus I/O expander optimized for this supply range. The host and expander should use compatible logic levels, and external I2C pull-ups must be referenced to the bus supply voltage rather than an unrelated supply rail.
Where can I download the PCA9554N datasheet?
The PCA9554N datasheet and product information are available from the NXP product page at https://www.nxp.com/part/PCA9554N. The manufacturer page identifies the DIP16 plastic package, including 16 leads, a 2.54 mm pitch, and body dimensions of 19 mm × 6.35 mm × 4.2 mm. Use the manufacturer datasheet for the complete electrical characteristics, register map, timing limits, and pin-description table.
Where can I find the PCA9554N pinout?
The PCA9554N pinout is defined in the pin-description table of the NXP PCA9554 datasheet. Its DIP-16 arrangement provides A0, A1, A2, SCL, SDA, eight port pins, interrupt, ground, and supply connections. The package has 16 leads on a 2.54 mm pitch. Assign PCB tracks from the numbered manufacturer pin table rather than relying only on the functional block diagram, especially when continuity and polarity must be checked before assembly.
How many I2C devices can share a bus with PCA9554N?
Up to eight PCA9554-family devices can share one I2C or SMBus bus when their A0, A1, and A2 address inputs are assigned different combinations. The three hardware address pins provide eight address combinations. Each expander still needs a unique base address, and the complete bus must remain within the device's 400 kHz maximum clock rate while meeting the voltage, capacitance, and pull-up requirements of the bus.
What can replace PCA9554N as a drop-in part?
The PCA9554A is a close NXP-family alternative when a different device address is acceptable, but it is not an unconditional register-for-register replacement for every existing design. The original PCA9554 is also pin-to-pin and I2C-address compatible with the PCF8574 according to TI's PCA9554 product information, although software changes are required because of the PCA9554's enhanced register set. Always verify address selection, interrupt polarity, and firmware behavior before substitution.
Is PCA9554N compatible with PCF8574?
PCA9554N and PCF8574 are physically and bus-address compatible, but their software models are not identical. TI's PCA9554 product information states that PCA9554 is pin-to-pin and I2C-address compatible with PCF8574 while requiring software changes because of its enhanced features. Existing PCF8574 routines that only write or read simple port data may need revision for the PCA9554's direction, polarity, and interrupt registers.
Is the PCA9554N suitable for 3.3 V industrial control systems?
Yes, the PCA9554N is suitable for 3.3 V systems because its specified operating supply range includes 3.3 V within the overall 2.3 V to 5.5 V range. It provides eight GPIO lines and a 400 kHz I2C interface, making it practical for low-voltage control, monitoring, and configuration boards. Ensure pull-ups, address wiring, signal levels, and the interrupt output match the host controller's electrical limits.
How does the PCA9554N interrupt output work?
The PCA9554N can assert its interrupt output when a change is detected on a port configured as an input. The host can therefore remain idle until an input event requires service instead of continuously polling the eight GPIO pins. Interrupt behavior is controlled through the device's configuration registers, so firmware must configure the relevant pins and polarity correctly. The output should also be handled according to the open-drain signaling arrangement shown in the manufacturer documentation.
What is the difference between PCA9554N and PCA9554A?
The principal documented difference is the I2C address: NXP describes PCA9554AD as providing a different address from PCA9554, while the standard PCA9554 occupies its own address position. Both devices belong to the 8-bit PCA9554 GPIO-expander family, but changing address can affect system firmware and bus planning. The PCA9554N is the DIP-16 ordering option; confirm the exact package suffix and address behavior before treating the A-version as interchangeable.
Where can I buy PCA9554N and what is the lead time?
Use the Request a Quote form on this page to request current PCA9554N availability, authorized-channel sourcing, and lead time. The part is an NXP 8-bit I2C/SMBus I/O expander in a 16-DIP package, and current supply can change independently of technical compatibility. Provide the required quantity, date code, target delivery location, and whether reel, tray, tube, or other approved packaging is needed so procurement can confirm the exact orderable configuration.
What is the price of PCA9554N?
Use the Request a Quote form on this page for the current PCA9554N price and quantity availability. Pricing can vary with order quantity, lifecycle position, packaging, date code, authorized-channel conditions, and destination, so a static figure may not represent the purchasable offer. Include the annual forecast and production cadence in the request if procurement needs a stable planning basis.
Is PCA9554N in stock?
Current PCA9554N stock should be confirmed through the Request a Quote form on this page. The NXP product page identifies PCA9554N as an active product with a defined DIP16 package, but inventory changes by quantity, packaging, date code, and region. Submit the required quantity and target date to obtain a current availability confirmation rather than relying on a generic catalog-stock indicator.
What can replace PCA9554N when more I2C address options are needed?
The PCA9554A family is the most direct same-manufacturer option to evaluate when a different I2C address is needed. It retains the familiar 8-bit GPIO-expander concept but occupies a different address position, allowing an additional device to coexist on the same bus. Replacement is conditional on package fit and acceptance of the changed address in firmware. For a bridge, the manufacturer also identifies the PCF8574 as pin and bus-address compatible, although its software interface requires adaptation.
What are the key specifications of PCA9554N that engineers should know?
The PCA9554N provides eight GPIO pins, a 2.3 V to 5.5 V operating range, a 400 kHz I2C/SMBus interface, an interrupt output, and weak internal pull-ups. Three address pins, A0 through A2, permit eight address combinations, while the package is a 16-lead DIP with a 2.54 mm pitch and a 19 mm × 6.35 mm × 4.2 mm body. These features make it especially useful for extending compact embedded and industrial controllers that lack sufficient parallel I/O.
How is the PCA9554N configured for input and output operation?
Each PCA9554N port bit can be configured independently as an input or output through the device's direction-control register. Firmware should configure the direction before writing output data or interpreting input levels, especially when a port changes function during startup. The interrupt feature can then report changes on configured input pins. Application code should also account for the weak internal pull-ups and provide stronger external pull-ups when the bus requires them.

کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9554N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose PCA9554N when a controller needs eight additional I2C-controlled GPIO lines and the target PCB uses a through-hole DIP-16 footprint. Its 2.3 V to 5.5 V range, 400 kHz bus support, hardware address inputs, and interrupt output are well suited to 3.3 V and 5 V embedded systems. Choose PCA9554A when you need a different I2C address, provided firmware and bus planning are updated. Consider PCA9554 from Texas Instruments when a second source with the same functional architecture is required, but verify exact package suffix, electrical limits, address, and qualification. PCF8574-family devices are useful when their simpler register model fits the firmware, although TI states that moving from PCF8574 to PCA9554 requires software changes. In every case, validate pinout, address straps, pull-up resistance, interrupt polarity, and GPIO direction before production.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ PCA9554A PCA9554 PCA9554A PCF8574 PCF8574A
Package DIP-16 DIP-16 DIP-16 DIP-16 DIP-16 DIP-16
Brand NXP Semiconductors NXP Semiconductors Texas Instruments Texas Instruments Texas Instruments NXP Semiconductors
GPIO Count 8 bits 8 bits 8 bits 8 bits 8 bits 8 bits
Address Configuration A0, A1, and A2 hardware inputs Different PCA9554-family address A0, A1, and A2 hardware inputs Different PCA9554-family address Compatible address arrangement Different PCF8574-family address
Software Compatibility PCA9554 register model PCA9554A register model with different address PCA9554 register model PCA9554A register model with different address Software changes required Software changes required

اہم امتیازی خصوصیات

  • Provides a genuine DIP-16 footprint rather than requiring an SMT-only conversion (بمقابلہPCA9554A)
  • Combines eight GPIO lines with a dedicated interrupt output (بمقابلہPCF8574)
  • Supports eight bus address combinations through three hardware inputs (بمقابلہPCA9554A)
  • Operates across common embedded logic-voltage rails (بمقابلہPCF8574A)

ڈیزائن نوٹس

Place the decoupling capacitor as close as practical to the PCA9554N VCC and ground pins, and route SCL and SDA away from switching nodes and high-current return paths. The DIP-16 footprint uses a 2.54 mm pitch. Keep address-input traces short and deliberate because A0, A1, and A2 determine the device's bus address. If multiple expanders are installed, label the address straps clearly to reduce configuration errors.

The internal pull-ups are weak and should not be assumed to provide adequate bus rise time at 400 kHz. Determine total bus capacitance and select external pull-up resistance for the actual bus voltage, trace length, number of nodes, and clock rate. Verify the resulting rise and fall times with an oscilloscope on the assembled board, particularly when the harness is long or several expanders share the bus.

Do not assume that a PCA9554N is a register-for-register PCF8574 replacement. TI identifies pin-to-pin and I2C-address compatibility with PCF8574 but also states that software changes are required for PCA9554's enhancements. Review direction-control, input/output polarity, interrupt, and initialization behavior in firmware. When changing to PCA9554A, update the addressed device and verify that the new address does not conflict with another peripheral.

The PCA9554N is a logic interface and is not intended to drive relays, high-current LEDs, or other power loads directly. Use suitable transistors, buffer drivers, or protection circuits for those loads. Define the output-pin current limits and total supply current from the manufacturer datasheet, account for simultaneous output activity, and size VCC decoupling so switching loads do not create unacceptable rail transients.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

Compliance attributes require confirmation from the current manufacturer product documentation or applicable declaration.

متعلقہ تلاشیں

pca9554 datasheet pca9554 device tree binding PCA9554N datasheet pdf PCA9554N pinout PCA9554N DIP-16 footprint PCA9554N 8-bit GPIO expander PCA9554N 2.3V 5.5V PCA9554N 400 kHz I2C PCA9554N vs PCA9554A PCA9554N drop-in replacement PCA9554N replacement PCA9554N price PCA9554N stock NXP PCA9554N application circuit

متعلقہ اجزاء اور اصطلاحات

NXP Semiconductors PCA9554N PCA9554A PCA9554 PCF8574 PCF8574A GPIO expander I/O expander interface IC semiconductor I2C SMBus general-purpose input/output DIP-16 dual in-line package through-hole 2.54 mm lead pitch interrupt output weak pull-up resistor hardware address input A0 A1 A2 400 kHz I2C
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں