PIC16F1824-E/P - 8-Bit 32MHz Flash MCU | Microchip
MPN: PIC16F1824-E/P ✓ AktifPIC16F1824-E/P Genel Bakış
A microcontroller is a programmable system-on-chip that integrates a processor core, Flash memory, RAM, oscillators, analog conversion, digital I/O, and communication peripherals on one device. The PIC16F1824 belongs to the enhanced mid-range PIC16 family, combining a RISC-based architecture with integrated capacitive-touch sensing and nanoWatt XLP low-power features. This hierarchy places it within 8-bit microcontrollers, embedded controllers, and programmable logic devices.
Program storage is organized as 4K x 14 words within a 7 KB Flash device, allowing the firmware to be programmed and rewritten through the Microchip development toolchain. Integrated debug support removes the need for a dedicated debug header, while programming and debug support is available through PICkit 3 and MPLAB ICD 3. The manufacturer lists the base PIC16F1824 family as in production.
The device is suited to compact embedded control systems that require deterministic 8-bit processing, low-power operation, and a straightforward through-hole footprint. Typical uses include industrial control panels, sensing nodes, instrumentation, small motor-control boards, and low-cost consumer appliances. Capacitive-touch mTouch capability supports touch-sensitive keypads and control surfaces without separate discrete touch controllers.
For new PCB layouts, confirm each signal connection against the manufacturer pin-description table before routing. Decouple VDD near the device with a local 0.1 µF ceramic capacitor, and add bulk supply capacitance at the board's power-distribution point. The 14-pin PDIP footprint is mechanically convenient for prototypes and through-hole production but occupies more board area than the corresponding surface-mount options.
This page combines manufacturer lifecycle information, package and memory details, programming guidance, replacement options, and practical PCB considerations. It also organizes alternative MPNs by package and temperature grade so engineers can identify the closest upgrade path before releasing a new PCB.
Drop-in alternatifler için PIC16F1824-E/P — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller PIC16F1824-E/P (aynı form faktörü ve ayağa oturma) — farklı olan Package, ADC, Internal Oscillator, Low-Power Technology, Architecture.
PIC16F1824-I/P
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F1823-I/P
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F1825-I/P
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F1827-I/P
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →PIC16F1822-I/P
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
PIC16F1824-E/P Maksimum Değerlendirmeler & Elektriksel Özellikler
| Manufacturer | Microchip Technology |
| Product Type | 8-bit Flash Microcontroller |
| Architecture | Enhanced mid-range PIC16 with RISC-based core |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 7 KB |
| Program Memory Organization | 4K x 14 words |
| Paket | 14-pin PDIP, 0.300 inch body width, 7.62 mm pitch |
| Montaj Türü | Through-hole |
| Temperature Grade | Extended (-40°C to +125°C) |
| Program Memory Type | Flash |
| Capacitive Touch | mTouch capacitive-touch sensing supported |
| Low-Power Technology | nanoWatt XLP |
| Integrated Debug Support | Yes, on-device debug support |
| Debug Header Required | No |
| Programming Support | PICkit 3 and MPLAB ICD 3 |
| Yaşam Döngüsü Durumu | In Production |
| RoHS Durumu | Compliant |
PIC16F1824-E/P Pin Yapısı
| Pin 1 | RA5 — General-purpose I/O pin RA5 |
| Pin 2 | RA4 — General-purpose I/O pin RA4 |
| Pin 3 | RA3 — General-purpose I/O pin RA3 |
| Pin 4 | RA2 — General-purpose I/O pin RA2 |
| Pin 5 | RA1 — General-purpose I/O pin RA1 |
| Pin 6 | RA0 — General-purpose I/O pin RA0 |
| Pin 7 | VSS — Ground reference connection |
| Pin 8 | RB0 — General-purpose I/O pin RB0 |
| Pin 9 | RB1 — General-purpose I/O pin RB1 |
| Pin 10 | RB2 — General-purpose I/O pin RB2 |
| Pin 11 | RB3 — General-purpose I/O pin RB3 |
| Pin 12 | VDD — Positive supply-voltage connection |
| Pin 13 | RC5 — General-purpose I/O pin RC5 |
| Pin 14 | RC4 — General-purpose I/O pin RC4 |
Tipik Uygulamalar
PIC16F1824-E/P için uygundur 6 uygulamas: Industrial Control Panel, Capacitive-Touch Keypad, Battery-Powered Sensing Node, Programmable Logic Controller, Instrumentation and Data Acquisition, Small Motor and Relay Control.
Industrial Control Panel
The PIC16F1824-E/P is suitable for compact industrial control panels because its 32 MHz 8-bit core executes control logic quickly, while 7 KB of Flash provides room for state machines, menu handling, and input validation. The 14-pin PDIP package simplifies through-hole assembly and serviceable prototypes. Use the mTouch inputs for front-panel buttons and configure debouncing in firmware to prevent switch-bounce events. Add local 0.1 µF decoupling at VDD and a bulk capacitor near the supply entry point to control transient noise. The extended-temperature grade supports designs requiring a wider operating range than the industrial option, while the integrated debug support permits programming through PICkit 3 without a dedicated header.
Önerilen
Capacitive-Touch Keypad
The mTouch capacitive-touch capability of the PIC16F1824-E/P allows a keypad, door-control panel, or appliance interface to detect touch electrodes without a separate touch-controller IC. Its 32 MHz clock provides adequate response time for debouncing, gesture interpretation, and illumination updates, while the 4K x 14-word Flash organization stores the sensing and UI firmware. Keep touch-electrode traces short, guard them with a grounded pour, and keep high-current switching paths away from the sensing inputs to reduce coupling. Verify the required touch pins and shared functions against the manufacturer pin-description table because multiplexed port functions can affect sensor assignment.
Önerilen
Battery-Powered Sensing Node
The PIC16F1824-E/P can serve as the controller in a battery-powered environmental or condition-monitoring node because the PIC16F1824 family includes nanoWatt XLP low-power technology. The 8-bit architecture avoids the overhead of a higher-power processor when the design only samples sensors, applies thresholds, and transmits occasional results. Operating current varies with the selected clock, active peripherals, and duty cycle, so calculate the average consumption from the specific power modes used by the firmware. Place the MCU close to its decoupling capacitor, keep unused I/O in defined states, and isolate the radio or communications section from sensitive analog measurement paths.
Önerilen
Programmable Logic Controller
The PIC16F1824-E/P can implement compact PLC-like control for pumps, valves, relays, and small machines where deterministic I/O handling matters more than high processing throughput. Its 32 MHz maximum clock and Flash program memory support combination logic, timers, counters, and communication routines in a single 14-pin controller. Use the manufacturer I/O mapping to assign outputs and verify current limits for each port before connecting loads. Because the PDIP package exposes only a limited number of I/O pins, use an expander or driver circuit when the design needs more inputs or outputs than the package provides, and keep inductive loads physically separated from sensitive logic traces.
Önerilen
Instrumentation and Data Acquisition
The PIC16F1824-E/P is appropriate for front-end instrumentation that gathers digital measurements, performs scaling, drives a local display, and sends results to a host. The 32 MHz clock supports responsive sampling and filtering, while integrated debug makes firmware bring-up straightforward. Confirm the device's ADC and timer resources in the manufacturer datasheet before assigning a specific measurement channel, since the supplied catalog data does not state the converter resolution. Place analog and digital return paths appropriately, provide a local bypass capacitor at VDD, and use short traces for measurement inputs to minimize pickup. A serial transceiver can extend the design when remote communication is required.
Önerilen
Small Motor and Relay Control
The PIC16F1824-E/P can control relays, solenoids, stepper indexing, or small motors in compact automation modules. The 8-bit core is sufficient for sequencing, limit-switch debouncing, and timing functions, while Flash allows field-updatable control logic. Keep the MCU and its decoupling away from relay contacts and motor wiring to reduce electromagnetic coupling, and use transistor or MOSFET driver circuits rather than driving inductive loads directly from a port pin. Add flyback protection across the load and separate high-current return paths from the device ground reference. Verify whether the required motor-control peripherals and timer resources are available in the selected family variant before finalizing the firmware.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: PIC16F1824-E/P — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | PIC16F1824-I/P | PIC16F1823-I/P | PIC16F1825-I/P | PIC16F1827-I/P | PIC16F1822-I/P |
|---|---|---|---|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Temperature Grade | Extended | Industrial | Industrial | Industrial | Industrial | Industrial |
| Processor Architecture | 8-bit enhanced mid-range PIC16 | 8-bit enhanced mid-range PIC16 | 8-bit enhanced mid-range PIC16 | 8-bit enhanced mid-range PIC16 | 8-bit enhanced mid-range PIC16 | 8-bit enhanced mid-range PIC16 |
| Integrated Debug Support | Yes | Yes | Yes | Yes | Yes | Yes |
| Capacitive Touch | mTouch supported | mTouch supported | Family-dependent | Family-dependent | Family-dependent | Family-dependent |
| Programming Support | PICkit 3 and MPLAB ICD 3 | PICkit 3 and MPLAB ICD 3 | MPLAB-compatible programmer | MPLAB-compatible programmer | MPLAB-compatible programmer | MPLAB-compatible programmer |
Ana Farklılayıcılar
- Extended-temperature ordering option (karşılaştırma:PIC16F1824-I/P)
- 7 KB Flash in a through-hole controller (karşılaştırma:PIC16F1822-I/P)
- mTouch integration without a separate controller (karşılaştırma:PIC16F1822-I/P)
- Integrated debugging simplifies development (karşılaştırma:PIC16F1823-I/P)
Tasarım Notları
Place the device close to the board's regulated supply and place a 0.1 µF ceramic bypass capacitor directly across VDD and VSS. Add a separate bulk capacitor near the supply entry point to handle longer traces and higher switching currents. Keep the capacitor return short and connect it to the device ground reference rather than routing it through a noisy load-current path.
Route mTouch electrode traces as short, guarded signals and keep them away from relays, motor windings, mains-adjacent wiring, and high-edge-rate clock signals. A grounded guard surrounding each electrode reduces capacitive pickup from adjacent copper. Validate the selected touch channel assignment against the 41419A manufacturer pin-description table because port multiplexing may restrict electrode placement.
Do not assume that a 14-pin PDIP ordering code guarantees identical firmware across every PIC16F182x variant. Program-memory size, RAM, timers, serial interfaces, analog channels, and pin multiplexing can differ between the 1822, 1823, 1824, 1825, and 1827 devices. Review the device-specific pin and peripheral tables, rebuild with the replacement header, and test all interrupt and timer assumptions before production release.
For battery-powered designs, calculate average consumption from the firmware's active current, sleep current, wake-up interval, and the duty cycle of the radio or sensor interface. Use the peripheral shutdown bits and clock-gating options provided by the device where the application allows them. Avoid leaving unused port outputs actively driving external nodes, since input and output leakage can dominate the standby budget in a low-current design.
Uyumluluk Bilgisi
The manufacturer lists RoHS-compliant PIC16F1824-family devices. AEC-Q100 automotive qualification, REACH status, lead-free status, halogen-free status, and conflict-minerals declarations are not established for this exact ordering code.