Microchip Technology

PIC24F08KL401T-I/SS - 16-Bit 32MHz MCU | Microchip

MPN: PIC24F08KL401T-I/SS ✓ Aktif
3 V Vdss 18 mA source and 18 mA sink per pin Id 20-pin SSOP, 5.30 mm width Package 32 MHz Speed 8 KB Flash (2.75K x 24 bits) Memory
MOQ: 1 |

PIC24F08KL401T-I/SS Genel Bakış

The Microchip Technology PIC24F08KL401T-I/SS is a 16-bit PIC XLP 24F microcontroller with a 32 MHz system speed, 8 KB of program Flash memory, 1 KB of SRAM, and a 512-byte EEPROM in a 20-pin SSOP package. It is designed for cost-sensitive embedded products that require compact size, low-power operation, and flexible serial communications.

A PIC24F microcontroller is a 16-bit embedded-processing member of the Microchip PIC family. Its wider processing architecture supports embedded-control tasks that need more computational capability than an 8-bit MCU while retaining the simplicity, low cost, and power efficiency associated with highly integrated single-chip controllers. The PIC XLP family emphasizes low-power operation for battery-operated, portable, and energy-conscious equipment.

Program memory is organized as 8 KB, or 2.75K by 24 bits, and the device includes 1 KB of RAM plus 512 bytes of EEPROM. The integrated 10-bit ADC supports analog measurements, while the serial interfaces include I2C, SPI, UART/USART, IrDA, and LIN connectivity. Two 16-bit timer/counter blocks, up to two 8-bit timer/counters, and two capture/compare/PWM modules support timing, measurement, motor-control, and waveform-generation functions.

The device operates from a 3 V supply and runs at 32 MHz. Its 20-pin SSOP package is approximately 5.30 mm wide, making it appropriate for compact control boards. Digital I/O supports high-current sink and source operation of 18 mA per pin, and configurable open-drain outputs are available for interfaces requiring wired behavior. The MCU also includes brown-out detection and reset functionality for more reliable operation when the supply voltage falls outside its intended operating condition.

Typical uses include compact industrial controllers, automotive accessory modules, sensor nodes, battery-powered instruments, and low-cost consumer appliances. Its combination of EEPROM, ADC, communications peripherals, and timing resources allows a single-chip implementation for designs that would otherwise require several discrete components.

Board layout should preserve the decoupling structure and programming interface required by the manufacturer datasheet. Place input and output capacitors close to their associated supply pins, route oscillator and programming signals away from high-current switching nodes, and verify the exposed programming and debug connections before releasing the PCB layout.

This product page consolidates the controller's core memory, connectivity, analog, timing, and package characteristics with practical application guidance, verified alternatives, and engineering-focused replacement considerations for embedded-product planning.

Drop-in alternatifler için PIC24F08KL401T-I/SS — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller PIC24F08KL401T-I/SS (aynı form faktörü ve ayağa oturma) — farklı olan Package, ADC, Communication, Core Architecture, I/O Pins.

Microchip Technology
Package: 20-pin SSOP (5.30 mm body width)
ADC: 10-bit, up to 12 channels
Communication: MSSP (I2C/SPI), 2 x UART, IrDA, LIN
Microchip Technology
Package: 20-SOIC (7.50 mm body width)
ADC: 10-bit, 9-channel (approx.)
Communication: 1x MSSP (I2C/SPI), 1x UART

PIC24F08KL401-I/SS

✅ Yerleştirme
Microchip Technology
📦 20-SSOP
PIC24F (16-bit modified Harvard RISC) · 8 KB (2.75K x 24 words) · 1 KB · 512 bytes · 32 MHz (16 MIPS) · 1.8 V to 3.6 V · -40 C to +85 C (Industrial, -I grade) · 20-pin SSOP (5.30 mm body width)

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

PIC24F08KL401T-I/SS Maksimum Değerlendirmeler & Elektriksel Özellikler

Product Type 16-bit PIC XLP 24F Flash Microcontroller
Maximum CPU Frequency 32 MHz
Program Memory 8 KB Flash (2.75K x 24 bits)
Data Memory 1 KB RAM
EEPROM 512 bytes
İşletim Besleme Gerilimi 3 V
ADC Resolution 10 bits
Timer/Counter Resources Two 16-bit and up to two 8-bit timer/counters
Capture/Compare/PWM Modules 2 CCP modules
Serial Interfaces I2C, SPI, UART/USART, IrDA, and LIN
External Interrupt Sources Up to 3
Digital I/O Current 18 mA source and 18 mA sink per pin
Open-Drain Output Configurable on digital I/O pins
Paket 20-pin SSOP, 5.30 mm width
Montaj Türü Surface mount
İşletim Sıcaklığı Aralığı -40°C to 85°C

PIC24F08KL401T-I/SS 20-pin ssop, 5.30 mm width Pin Yapısı Kılavuzu

PIC24F08KL401T-I/SS (20-pin ssop, 5.30 mm width paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.

20-pin ssop, 5.30 mm width paket pin çizelgesi için PIC24F08KL401T-I/SS

Ayrıntılı pin çıkış verisi mevcut değil: PIC24F08KL401T-I/SS.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

PIC24F08KL401T-I/SS için uygundur 6 uygulamas: Compact Industrial Sensor Node, Automotive Accessory Control Module, Battery-Powered Measurement Instrument, Small Motor and PWM Controller, Connected Consumer Appliance, Communication Interface Module.

🏭

Compact Industrial Sensor Node

The PIC24F08KL401T-I/SS fits compact sensor nodes because its 16-bit core operates at 32 MHz while the device retains only 8 KB of Flash, 1 KB of RAM, and 512 bytes of EEPROM. The integrated 10-bit ADC can acquire analog sensor signals without a separate converter, and the I2C or SPI interface can connect temperature, pressure, motion, or chemical sensors. Configure unused ports for low-power wake events and use the brown-out detector to protect operation as the battery supply declines. This integration reduces board area and component count, while the PIC XLP architecture supports duty-cycled measurements that are important in industrial monitoring equipment.

🚗

Automotive Accessory Control Module

The PIC24F08KL401T-I/SS is appropriate for compact automotive accessory controllers where a 3 V supply, 16-bit processing, and mixed signal control are required. Its 10-bit ADC supports analog sensing, while LIN and UART/USART connectivity can connect the controller to vehicle networks and diagnostic equipment. Two CCP modules can generate precise PWM outputs for motors or indicators, and the timer resources support debouncing and periodic tasks. The 20-pin SSOP footprint helps limit board area in door, climate, lighting, or seat modules. Validate the selected ordering code against the complete vehicle temperature requirement and use the manufacturer qualification information before production release.

🔧

Battery-Powered Measurement Instrument

PIC24F08KL401T-I/SS supports battery-powered instruments where low-power standby operation and mixed measurement are more important than maximum memory capacity. The 512-byte EEPROM can retain calibration or configuration data close to the controller, and the 10-bit ADC provides an economical analog front end for common sensors. I2C and SPI allow connection to displays, memory, or higher-resolution converters, while the two CCP modules can drive indicators or perform excitation functions. The 16-bit processing path is useful for filtering, scaling, and control calculations. Use the PIC XLP sleep and wake features to define the duty cycle, then verify brown-out behavior and input limits across the full battery discharge range.

⚡

Small Motor and PWM Controller

The PIC24F08KL401T-I/SS can control small motors, solenoids, and LED arrays because it includes two CCP modules, multiple 16-bit timer/counters, and programmable open-drain digital outputs. The 32 MHz 16-bit core supports deterministic timing calculations and closed-loop control, while the 10-bit ADC can monitor current, position, temperature, or supply conditions. Configure open-drain outputs only where the external interface requires that behavior, and use push-pull outputs for ordinary digital loads. The integrated brown-out detection is valuable when motor transients can disturb the supply. Layout the PCB with short high-current paths, adequate supply decoupling, and separated sensitive signal routes to reduce switching noise and false comparator or ADC events.

📱

Connected Consumer Appliance

The PIC24F08KL401T-I/SS is well suited to cost-sensitive consumer appliances that need local control plus several communication choices. I2C and SPI can support sensors and local peripherals, UART/USART can connect a human interface or service port, and IrDA offers an optical communication option in designs where wired interfaces are undesirable. The 512-byte EEPROM preserves settings through power loss, and the 10-bit ADC can monitor knobs, switches, temperature, or supply voltage. With 8 KB of Flash, firmware should be structured around compact control logic and communication handlers. The 20-pin SSOP package reduces footprint, but pin budgeting should account for programming, debugging, supply, ground, and communication functions during early schematic design.

🌐

Communication Interface Module

The PIC24F08KL401T-I/SS can serve as a protocol-conversion or embedded-interface module because it combines I2C, SPI, UART/USART, IrDA, and LIN in one controller. The 16-bit architecture can manage framing, buffering, diagnostics, and configuration logic while the 32 MHz clock provides margin for interrupt-driven transfers. Use the 10-bit ADC for optional analog monitoring and the EEPROM for calibration or protocol settings. Dedicated CCP modules can provide periodic timing or generated waveforms when a peripheral master cannot meet a system interval. The compact 20-pin SSOP package is useful in gateway-like products, although the final pin allocation must support the selected communication combination and maintain access to ICSP programming.

Önerilen Ürünler Özeti

PIC24F08KL401-I/SS Microchip Technology Kullanıldığı Yer: Compact Industrial Sensor Node, Automotive Accessory Control Module, Battery-Powered Measurement Instrument, Small Motor and PWM Controller, Connected Consumer Appliance, Communication Interface Module PIC24F16KL401 Higher-memory PIC24F family option when firmware growth requires it Kullanıldığı Yer: Compact Industrial Sensor Node, Automotive Accessory Control Module, Battery-Powered Measurement Instrument, Small Motor and PWM Controller, Connected Consumer Appliance, Communication Interface Module
What are the key specifications of PIC24F08KL401T-I/SS that engineers should know?
The PIC24F08KL401T-I/SS combines a 16-bit PIC core, 32 MHz operation, 8 KB of Flash, 1 KB of RAM, and 512 bytes of EEPROM in a 20-pin SSOP package. According to the Microchip product page and manufacturer datasheet, it also includes a 10-bit ADC, two CCP modules, 16-bit timer/counters, and I2C, SPI, UART/USART, IrDA, and LIN interfaces. These resources make it a practical single-chip choice for compact embedded-control and connected-sensor designs.
What is the operating voltage of PIC24F08KL401T-I/SS?
The PIC24F08KL401T-I/SS operates from a 3 V supply. The 3 V operating point is identified in the Microchip product listing, while the manufacturer datasheet should be consulted for the exact operating limits, absolute maximum ratings, and relationships among supply voltage, clock frequency, and I/O voltage. The 20-pin SSOP implementation also makes voltage and decoupling checks especially important during compact PCB layout.
How much Flash, RAM, and EEPROM does PIC24F08KL401T-I/SS have?
The PIC24F08KL401T-I/SS provides 8 KB of program Flash, 1 KB of RAM, and 512 bytes of EEPROM. The Flash is described by Microchip as 2.75K words by 24 bits. According to the manufacturer datasheet and product listings, this combination suits cost-sensitive firmware that needs more processing capability than an 8-bit controller but can remain within a small flash and RAM budget.
Where can I download the PIC24F08KL401T-I/SS datasheet PDF?
The PIC24F08KL401T-I/SS datasheet PDF is available through the Microchip PIC24F08KL401 product page and the linked manufacturer documentation. The product family is identified as the PIC XLP 24F series, and the exact ordered device is the industrial-temperature, 20-pin SSOP configuration. Use the document's pin-description table when assigning PCB nets and confirm electrical limits before applying the device outside the stated operating conditions.
Where can I find the PIC24F08KL401T-I/SS pinout?
The PIC24F08KL401T-I/SS pinout is documented in the manufacturer datasheet's pin-description and package drawings. This 20-pin SSOP device includes power, ground, programming, I/O, and peripheral functions that must be assigned according to the exact suffix configuration. Use the pin table in the datasheet rather than inferring a schematic from another package variant, and preserve access to the ICSP programming pins in the board layout.
What is PIC24F08KL401T-I/SS used for?
PIC24F08KL401T-I/SS is used for compact embedded-control products that combine mixed signal measurement with serial communications. Its 10-bit ADC supports sensor inputs, its 16-bit timers and two CCP modules support timing and PWM tasks, and its I2C, SPI, UART/USART, IrDA, and LIN connectivity supports sensors, actuators, and external controllers. The PIC XLP architecture is particularly relevant to battery-operated and low-power designs.
What can replace PIC24F08KL401T-I/SS on the same PCB?
PIC24F08KL401-I/SS is the closest documented drop-in candidate because it retains the same 20-pin SSOP footprint, 16-bit core, 32 MHz speed, 8 KB Flash, 1 KB RAM, and 512-byte EEPROM. Its principal difference is the temperature-grade code, so the replacement should be checked against the original system's full operating-temperature requirement. No verified cross-brand, pin-compatible replacement was identified for this exact footprint.
Is PIC24F08KL401T-I/SS suitable for battery-powered sensor nodes?
Yes, PIC24F08KL401T-I/SS is suitable for battery-powered sensor nodes because it belongs to the PIC XLP low-power MCU family and combines EEPROM with analog and serial peripherals. According to the manufacturer datasheet, the device includes brown-out detection and reset, 18 mA source and sink capability on each I/O pin, and configurable open-drain outputs. Actual battery life still depends on the selected sleep modes, wake sources, sensor duty cycle, and supply regulator efficiency.
What is the difference between PIC24F08KL401T-I/SS and PIC24F08KL401-I/SS?
The principal documented difference is the ordering suffix: the target includes T, while PIC24F08KL401-I/SS does not. Both are listed as 16-bit, 32 MHz PIC XLP 24F devices with 8 KB Flash, 1 KB RAM, 512-byte EEPROM, and a 20-pin SSOP package. The manufacturer ordering information should be checked to confirm the exact temperature range associated with each suffix before using one as a replacement.
PIC24F08KL401T-I/SS vs PIC24F16KL401 - which is better for a low-cost design?
PIC24F08KL401T-I/SS is generally the better choice when 8 KB of Flash is sufficient because it provides 16-bit processing, a 10-bit ADC, and multiple serial interfaces at a lower memory level than the PIC24F16KL401 family member. PIC24F16KL401 provides more program-memory capacity and may suit larger firmware. Both remain in Microchip's PIC XLP 24F ecosystem, but exact package and pin compatibility must be confirmed for the selected ordering codes.
When should I choose PIC24F08KL401T-I/SS over another 16-bit MCU?
Choose PIC24F08KL401T-I/SS when a design needs a 16-bit core at 32 MHz but can operate within 8 KB of Flash, 1 KB of RAM, and 512 bytes of EEPROM. Its integrated 10-bit ADC, LIN, IrDA, UART/USART, SPI, and I2C interfaces reduce external component count in connected embedded products. It is particularly attractive for compact industrial, automotive-accessory, instrument, and sensor-node designs where PIC XLP low-power behavior is valuable.
Is PIC24F08KL401T-I/SS in stock and what is its lead time?
Stock status and a current production lead time should be requested through the Request a Quote form on this page. The exact target MPN is identified by the manufacturer and distributor listings, but their inventory messages are not permanent production commitments. For an approved design, request the current lifecycle, stock, date-code, and traceability information together with the required reel or tube packing method.
Where can I buy PIC24F08KL401T-I/SS online?
Use the Request a Quote form on this page to buy PIC24F08KL401T-I/SS with the exact suffix, including its industrial-temperature code and 20-pin SSOP package. When requesting the quote, specify the required quantity, packing format, date-code preference, and destination. The quote workflow avoids substitution between the target T-grade device, the non-T ordering code, and other package configurations.
What is the price of PIC24F08KL401T-I/SS?
The current unit price for PIC24F08KL401T-I/SS should be obtained through the Request a Quote form on this page. The quote should be requested for the exact T-grade, SSOP ordering code so that temperature-grade, packing, and traceability requirements are not mixed with related variants. Pricing, availability, and delivery scheduling should be confirmed together for the planned production quantity.
What programming and debugging tools support PIC24F08KL401T-I/SS?
PIC24F08KL401T-I/SS is programmed and debugged through the PIC24 family's ICSP and In-Circuit Serial Programming workflow, with support from Microchip's MPLAB development environment and compatible programmers. According to the Microchip PIC24F16KL401 family information, MPLAB Snap can use a High-Speed USB 2.0 interface and an 8-pin SIL connector to reach the target through two I/O pins and the reset line. Preserve those programming connections in the PCB design.

Mühendislik referans verileri: PIC24F08KL401T-I/SS — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose PIC24F08KL401T-I/SS for compact 16-bit embedded-control designs that can fit within 8 KB of Flash and 1 KB of RAM and benefit from integrated ADC, EEPROM, LIN, IrDA, UART/USART, SPI, and I2C peripherals. It is particularly suitable for low-power sensor nodes, automotive accessory modules, measurement instruments, and small appliance controllers. PIC24F08KL401-I/SS is the closest same-footprint alternative when its temperature-grade code satisfies the system requirement, but the T and non-T ordering codes must be checked against the complete environmental specification. PIC24F16KL401 is preferable when firmware requirements exceed the target's memory capacity, although the exact package and pinout must be confirmed before treating it as a drop-in replacement. The /SO suffix must not be used as a footprint substitute for the narrow 20-SSOP target.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün PIC24F08KL401-I/SS
Package 20-SSOP 20-SSOP - same
Brand Microchip Technology Microchip Technology
Processor Architecture 16-bit PIC24 core 16-bit PIC24 core
Maximum CPU Frequency 32 MHz 32 MHz
Program Memory 8 KB Flash (2.75K x 24 bits) 8 KB Flash (2.75K x 24 bits)
RAM 1 KB 1 KB
EEPROM 512 bytes 512 bytes
Operating Supply Voltage 3 V 3 V
ADC Resolution 10 bits 10 bits
Serial Interfaces I2C, SPI, UART/USART, IrDA, and LIN I2C, SPI, UART/USART, IrDA, and LIN
Temperature Ordering Code T-grade ordering code No T in ordering code
Timer and PWM Resources Two 16-bit timers, up to two 8-bit timers, and two CCP modules Two 16-bit timers, up to two 8-bit timers, and two CCP modules

Ana Farklılayıcılar

  • Same 20-pin SSOP footprint as the closest documented alternative (karşılaştırma:PIC24F08KL401-I/SS)
  • Integrated multi-protocol connectivity (karşılaştırma:PIC24F08KL401-I/SS)
  • Mixed-signal and timing resources integrated on one MCU (karşılaştırma:PIC24F08KL401-I/SS)

Tasarım Notları

Place the required input and output decoupling capacitors immediately beside their associated device pins, and keep the ground return path short. The MCU operates from a 3 V supply and includes brown-out detection, but the detection threshold does not replace correct supply regulation. When the board shares the 3 V rail with motors, relays, LEDs, or a switching converter, isolate noisy loads and add bulk and local bypass capacitance. Verify the voltage at the device pins under worst-case load transients rather than relying only on the nominal supply value.

Preserve access to the ICSP programming and debug signals on the PCB because these pins are needed for programming, initialization, and production test. Use a connector or test pads positioned for fixture access, and route the programming interface away from switching nodes and high-current motor traces. The 20-pin SSOP footprint is narrow, so work from the manufacturer package drawing and land pattern rather than estimating dimensions from a similar SSOP device.

Route oscillator, programming, and analog-sensing signals away from high-current outputs and fast-switching nodes. The I/O pins can source or sink 18 mA, but that capability does not remove the need for trace-width and thermal analysis when several outputs operate simultaneously. For analog measurements, keep the 10-bit ADC input path short, place its source impedance within the device's recommended range, and use a quiet ground reference to minimize conversion error and digital switching coupling.

Do not substitute the non-T ordering code without checking the required operating-temperature range, and do not use the similarly named /SO ordering code as a PCB replacement. The /SS device uses a narrow 20-pin SSOP footprint, while /SO identifies a different package option. Also account for the limited 8 KB Flash and 1 KB RAM when organizing drivers, communication stacks, and interrupt routines; removing a protocol feature or moving to a higher-memory family member may be preferable to uncontrolled memory growth.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The accessible product information identifies an industrial-temperature ordering code and a -40°C to 85°C operating range, but it does not explicitly document RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.

İlgili Aramalar

PIC24F08KL401T-I/SS datasheet PIC24F08KL401T-I/SS pinout PIC24F08KL401T-I/SS datasheet pdf PIC24F08KL401T-I/SS equivalent PIC24F08KL401T-I/SS replacement PIC24F08KL401T-I/SS vs PIC24F08KL401-I/SS PIC24F08KL401 20-SSOP pinout PIC24F08KL401 32MHz 8KB Flash PIC24F08KL401 low power sensor node Microchip PIC24F08KL401T-I/SS PIC24F08KL401T-I/SS price PIC24F08KL401T-I/SS stock PIC24F08KL401T-I/SS programming PIC24F08KL401T-I/SS schematic

İlgili Bileşenler ve Terimler

Microchip Technology PIC24F08KL401T-I/SS PIC24F08KL401-I/SS PIC24F16KL401 PIC24F PIC XLP 16-bit microcontroller Flash memory SRAM EEPROM 10-bit ADC I2C SPI UART/USART IrDA LIN Capture/Compare/PWM timer/counter brown-out detection ICSP MPLAB 20-pin SSOP surface mount low-power embedded control
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle