PIC24F08KL401T-I/SS - 16-Bit 32MHz MCU | Microchip
N.º de pieza: PIC24F08KL401T-I/SS ✓ ActivoPIC24F08KL401T-I/SS Descripción general
A PIC24F microcontroller is a 16-bit embedded-processing member of the Microchip PIC family. Its wider processing architecture supports embedded-control tasks that need more computational capability than an 8-bit MCU while retaining the simplicity, low cost, and power efficiency associated with highly integrated single-chip controllers. The PIC XLP family emphasizes low-power operation for battery-operated, portable, and energy-conscious equipment.
Program memory is organized as 8 KB, or 2.75K by 24 bits, and the device includes 1 KB of RAM plus 512 bytes of EEPROM. The integrated 10-bit ADC supports analog measurements, while the serial interfaces include I2C, SPI, UART/USART, IrDA, and LIN connectivity. Two 16-bit timer/counter blocks, up to two 8-bit timer/counters, and two capture/compare/PWM modules support timing, measurement, motor-control, and waveform-generation functions.
The device operates from a 3 V supply and runs at 32 MHz. Its 20-pin SSOP package is approximately 5.30 mm wide, making it appropriate for compact control boards. Digital I/O supports high-current sink and source operation of 18 mA per pin, and configurable open-drain outputs are available for interfaces requiring wired behavior. The MCU also includes brown-out detection and reset functionality for more reliable operation when the supply voltage falls outside its intended operating condition.
Typical uses include compact industrial controllers, automotive accessory modules, sensor nodes, battery-powered instruments, and low-cost consumer appliances. Its combination of EEPROM, ADC, communications peripherals, and timing resources allows a single-chip implementation for designs that would otherwise require several discrete components.
Board layout should preserve the decoupling structure and programming interface required by the manufacturer datasheet. Place input and output capacitors close to their associated supply pins, route oscillator and programming signals away from high-current switching nodes, and verify the exposed programming and debug connections before releasing the PCB layout.
This product page consolidates the controller's core memory, connectivity, analog, timing, and package characteristics with practical application guidance, verified alternatives, and engineering-focused replacement considerations for embedded-product planning.
Alternativas directas para PIC24F08KL401T-I/SS — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con PIC24F08KL401T-I/SS (mismo factor de forma y huella) — difiere en Package, ADC, Communication, Core Architecture, I/O Pins.
PIC24F08KL401-I/SS
✅ Sustitución directaConsulte el precio
Ver hoja de datos →PIC24F08KL401T-I/SS Valores máximos y características eléctricas
| Product Type | 16-bit PIC XLP 24F Flash Microcontroller |
| Maximum CPU Frequency | 32 MHz |
| Program Memory | 8 KB Flash (2.75K x 24 bits) |
| Data Memory | 1 KB RAM |
| EEPROM | 512 bytes |
| Tensión de alimentación de funcionamiento | 3 V |
| ADC Resolution | 10 bits |
| Timer/Counter Resources | Two 16-bit and up to two 8-bit timer/counters |
| Capture/Compare/PWM Modules | 2 CCP modules |
| Serial Interfaces | I2C, SPI, UART/USART, IrDA, and LIN |
| External Interrupt Sources | Up to 3 |
| Digital I/O Current | 18 mA source and 18 mA sink per pin |
| Open-Drain Output | Configurable on digital I/O pins |
| Encapsulado | 20-pin SSOP, 5.30 mm width |
| Tipo de montaje | Surface mount |
| Rango de temperatura de funcionamiento | -40°C to 85°C |
Guía de configuración de pines de PIC24F08KL401T-I/SS 20-pin ssop, 5.30 mm width
Configuración de pines para PIC24F08KL401T-I/SS (encapsulado 20-pin ssop, 5.30 mm width). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para PIC24F08KL401T-I/SS.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
PIC24F08KL401T-I/SS es adecuado para 6 aplicacións: Compact Industrial Sensor Node, Automotive Accessory Control Module, Battery-Powered Measurement Instrument, Small Motor and PWM Controller, Connected Consumer Appliance, Communication Interface Module.
Compact Industrial Sensor Node
The PIC24F08KL401T-I/SS fits compact sensor nodes because its 16-bit core operates at 32 MHz while the device retains only 8 KB of Flash, 1 KB of RAM, and 512 bytes of EEPROM. The integrated 10-bit ADC can acquire analog sensor signals without a separate converter, and the I2C or SPI interface can connect temperature, pressure, motion, or chemical sensors. Configure unused ports for low-power wake events and use the brown-out detector to protect operation as the battery supply declines. This integration reduces board area and component count, while the PIC XLP architecture supports duty-cycled measurements that are important in industrial monitoring equipment.
Recomendado
Automotive Accessory Control Module
The PIC24F08KL401T-I/SS is appropriate for compact automotive accessory controllers where a 3 V supply, 16-bit processing, and mixed signal control are required. Its 10-bit ADC supports analog sensing, while LIN and UART/USART connectivity can connect the controller to vehicle networks and diagnostic equipment. Two CCP modules can generate precise PWM outputs for motors or indicators, and the timer resources support debouncing and periodic tasks. The 20-pin SSOP footprint helps limit board area in door, climate, lighting, or seat modules. Validate the selected ordering code against the complete vehicle temperature requirement and use the manufacturer qualification information before production release.
Recomendado
Battery-Powered Measurement Instrument
PIC24F08KL401T-I/SS supports battery-powered instruments where low-power standby operation and mixed measurement are more important than maximum memory capacity. The 512-byte EEPROM can retain calibration or configuration data close to the controller, and the 10-bit ADC provides an economical analog front end for common sensors. I2C and SPI allow connection to displays, memory, or higher-resolution converters, while the two CCP modules can drive indicators or perform excitation functions. The 16-bit processing path is useful for filtering, scaling, and control calculations. Use the PIC XLP sleep and wake features to define the duty cycle, then verify brown-out behavior and input limits across the full battery discharge range.
Recomendado
Small Motor and PWM Controller
The PIC24F08KL401T-I/SS can control small motors, solenoids, and LED arrays because it includes two CCP modules, multiple 16-bit timer/counters, and programmable open-drain digital outputs. The 32 MHz 16-bit core supports deterministic timing calculations and closed-loop control, while the 10-bit ADC can monitor current, position, temperature, or supply conditions. Configure open-drain outputs only where the external interface requires that behavior, and use push-pull outputs for ordinary digital loads. The integrated brown-out detection is valuable when motor transients can disturb the supply. Layout the PCB with short high-current paths, adequate supply decoupling, and separated sensitive signal routes to reduce switching noise and false comparator or ADC events.
Recomendado
Connected Consumer Appliance
The PIC24F08KL401T-I/SS is well suited to cost-sensitive consumer appliances that need local control plus several communication choices. I2C and SPI can support sensors and local peripherals, UART/USART can connect a human interface or service port, and IrDA offers an optical communication option in designs where wired interfaces are undesirable. The 512-byte EEPROM preserves settings through power loss, and the 10-bit ADC can monitor knobs, switches, temperature, or supply voltage. With 8 KB of Flash, firmware should be structured around compact control logic and communication handlers. The 20-pin SSOP package reduces footprint, but pin budgeting should account for programming, debugging, supply, ground, and communication functions during early schematic design.
Recomendado
Communication Interface Module
The PIC24F08KL401T-I/SS can serve as a protocol-conversion or embedded-interface module because it combines I2C, SPI, UART/USART, IrDA, and LIN in one controller. The 16-bit architecture can manage framing, buffering, diagnostics, and configuration logic while the 32 MHz clock provides margin for interrupt-driven transfers. Use the 10-bit ADC for optional analog monitoring and the EEPROM for calibration or protocol settings. Dedicated CCP modules can provide periodic timing or generated waveforms when a peripheral master cannot meet a system interval. The compact 20-pin SSOP package is useful in gateway-like products, although the final pin allocation must support the selected communication combination and maintain access to ICSP programming.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para PIC24F08KL401T-I/SS — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | PIC24F08KL401-I/SS |
|---|---|---|
| Package | 20-SSOP | 20-SSOP - same |
| Brand | Microchip Technology | Microchip Technology |
| Processor Architecture | 16-bit PIC24 core | 16-bit PIC24 core |
| Maximum CPU Frequency | 32 MHz | 32 MHz |
| Program Memory | 8 KB Flash (2.75K x 24 bits) | 8 KB Flash (2.75K x 24 bits) |
| RAM | 1 KB | 1 KB |
| EEPROM | 512 bytes | 512 bytes |
| Operating Supply Voltage | 3 V | 3 V |
| ADC Resolution | 10 bits | 10 bits |
| Serial Interfaces | I2C, SPI, UART/USART, IrDA, and LIN | I2C, SPI, UART/USART, IrDA, and LIN |
| Temperature Ordering Code | T-grade ordering code | No T in ordering code |
| Timer and PWM Resources | Two 16-bit timers, up to two 8-bit timers, and two CCP modules | Two 16-bit timers, up to two 8-bit timers, and two CCP modules |
Diferenciadores clave
- Same 20-pin SSOP footprint as the closest documented alternative (frente a PIC24F08KL401-I/SS)
- Integrated multi-protocol connectivity (frente a PIC24F08KL401-I/SS)
- Mixed-signal and timing resources integrated on one MCU (frente a PIC24F08KL401-I/SS)
Notas de diseño
Place the required input and output decoupling capacitors immediately beside their associated device pins, and keep the ground return path short. The MCU operates from a 3 V supply and includes brown-out detection, but the detection threshold does not replace correct supply regulation. When the board shares the 3 V rail with motors, relays, LEDs, or a switching converter, isolate noisy loads and add bulk and local bypass capacitance. Verify the voltage at the device pins under worst-case load transients rather than relying only on the nominal supply value.
Preserve access to the ICSP programming and debug signals on the PCB because these pins are needed for programming, initialization, and production test. Use a connector or test pads positioned for fixture access, and route the programming interface away from switching nodes and high-current motor traces. The 20-pin SSOP footprint is narrow, so work from the manufacturer package drawing and land pattern rather than estimating dimensions from a similar SSOP device.
Route oscillator, programming, and analog-sensing signals away from high-current outputs and fast-switching nodes. The I/O pins can source or sink 18 mA, but that capability does not remove the need for trace-width and thermal analysis when several outputs operate simultaneously. For analog measurements, keep the 10-bit ADC input path short, place its source impedance within the device's recommended range, and use a quiet ground reference to minimize conversion error and digital switching coupling.
Do not substitute the non-T ordering code without checking the required operating-temperature range, and do not use the similarly named /SO ordering code as a PCB replacement. The /SS device uses a narrow 20-pin SSOP footprint, while /SO identifies a different package option. Also account for the limited 8 KB Flash and 1 KB RAM when organizing drivers, communication stacks, and interrupt routines; removing a protocol feature or moving to a higher-memory family member may be preferable to uncontrolled memory growth.
Información de cumplimiento
The accessible product information identifies an industrial-temperature ordering code and a -40°C to 85°C operating range, but it does not explicitly document RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.