PIC24FJ16MC102-I/SO - 16-Bit 16 MIPS Motor Control MCU | Microchip
MPN: PIC24FJ16MC102-I/SO ✓ AktifPIC24FJ16MC102-I/SO Genel Bakış
A motor-control microcontroller is a type of embedded microcontroller specialized for controlling motors, power stages, and position-feedback systems. In the product hierarchy, it combines a 16-bit MCU core, embedded control peripherals, communication interfaces, and analog functions on one integrated circuit. The PIC24FJ16MC102 belongs to Microchip's PIC24 family and adds CTMU, MCPWM, and Peripheral Pin Select capabilities to support economical motor-control systems.
Key features include a 16-bit architecture operating at 16 MIPS, 16 KB of program Flash, and 1 KB of RAM. Peripheral Pin Select allows supported digital functions to be assigned to an appropriate physical pin, simplifying board routing when motor-control signals, serial interfaces, and general-purpose I/O share a limited package. CTMU provides a dedicated capacitive-measurement resource, while the motor-control PWM peripherals support efficient generation of timing-critical control waveforms.
The device operates from 3 V to 3.6 V and includes I2C, IrDA, LIN, SPI, and UART connectivity according to its product documentation. Its 16-bit architecture and dedicated motor-control peripherals reduce the software and peripheral load associated with closed-loop motor systems. The 28-pin SOIC package also provides a mechanically accessible option for through-hole assembly rather than requiring a very small land grid array footprint.
Typical uses include low-cost BLDC and stepper-motor controllers, small industrial actuators, appliance drive systems, educational motor-control platforms, and compact embedded equipment with mixed analog and digital sensing. The MCPWM blocks are particularly useful for synchronized switching, while CTMU can support capacitive sensing for controls, position detection, or protective functions where the application requires it.
Designers should verify the exact peripheral-to-pin assignments for the selected 28-pin configuration in the Microchip pin-description table. Because the same physical pin can support multiple functions through Peripheral Pin Select, incorrect configuration can cause conflicts among PWM outputs, communications, and general-purpose I/O. Decoupling, programming access, clocking, and analog-ground layout should follow the guidance in the manufacturer data sheet.
This page combines the manufacturer's device information with practical application guidance, interface considerations, and verified same-package alternatives. It also highlights the differences between industrial-temperature and extended-temperature order codes so engineers can select a replacement without changing the PCB footprint.
Drop-in alternatifler için PIC24FJ16MC102-I/SO — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller PIC24FJ16MC102-I/SO (aynı form faktörü ve ayağa oturma) — farklı olan Package, Operating Voltage, Operating Temperature, ADC, Communication.
PIC24FJ16MC102-E/SO
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
PIC24FJ16MC102-I/SO Maksimum Değerlendirmeler & Elektriksel Özellikler
| Microcontroller Type | 16-bit motor-control microcontroller |
| CPU Performance | 16 MIPS |
| Program Memory | 16 KB Flash |
| Program Memory Organization | 5.5K x 24 words |
| Data Memory | 1 KB RAM |
| Operating Voltage | 3 V to 3.6 V |
| Paket | 28-pin SOIC |
| Montaj Türü | Surface Mount |
| Motor-Control PWM | MCPWM peripheral |
| Capacitive Touch | CTMU peripheral |
| Peripheral Routing | Peripheral Pin Select (PPS) |
| Serial Interfaces | I2C, IrDA, LIN, SPI, UART |
| RoHS Durumu | Compliant |
PIC24FJ16MC102-I/SO 28-pin soic Pin Yapısı Kılavuzu
PIC24FJ16MC102-I/SO (28-pin soic paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: PIC24FJ16MC102-I/SO.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
PIC24FJ16MC102-I/SO için uygundur 6 uygulamas: BLDC Motor Controllers, Stepper Motor Drives, Appliance Motor Control, Industrial Actuators, Motor-Control Education Platforms, Embedded Sensing and Control.
BLDC Motor Controllers
The PIC24FJ16MC102-I/SO fits compact brushless DC motor controllers because its 16-bit CPU executes at 16 MIPS while the dedicated MCPWM peripherals handle switching waveforms and timing-critical output functions. The 16 KB Flash and 1 KB RAM provide room for a motor-control state machine, communication handlers, and fault logic without requiring a separate DSP. Designers can use CTMU for capacitive sensing and Peripheral Pin Select to route supported signals around a constrained 28-pin SOIC layout. The principal design consideration is to configure every PWM and communication function before PCB routing so that multiplexed pins do not conflict.
Önerilen
Stepper Motor Drives
The PIC24FJ16MC102-I/SO is suitable for compact stepper-motor drives where predictable sequencing, limited board area, and multiple digital interfaces matter. The 16 MIPS 16-bit core can coordinate step-rate changes, position state, limit inputs, and host commands, while the MCPWM resources support the required timed outputs. Its 28-pin SOIC package remains accessible for conventional assembly, and PPS helps assign UART, SPI, or general-purpose I/O functions to usable pins. Firmware should include acceleration limits and loss-of-step recovery to protect the mechanism when commands arrive faster than the motor can follow.
Önerilen
Appliance Motor Control
Household and commercial appliances can use the PIC24FJ16MC102-I/SO to consolidate motor drive, user-interface sensing, and external communications in one 16-bit controller. Its CTMU peripheral supports capacitive touch or measurement functions, while the 3 V to 3.6 V operating range aligns with a 3.3 V appliance architecture. The MCU can manage a fan, pump, or damper motor and communicate with a main controller through I2C, SPI, UART, LIN, or IrDA. Because appliance motors are often noisy, keep switching stages and communication lines physically separated and verify grounding according to the manufacturer hardware guidance.
Önerilen
Industrial Actuators
The PIC24FJ16MC102-I/SO supports small industrial actuators that require deterministic PWM generation, local sensing, and network communication in a compact controller. Its 16 MIPS performance is appropriate for coordinating motor timing with status monitoring, while 16 KB Flash accommodates application firmware and 1 KB RAM supports short control loops. The I2C, SPI, UART, LIN, and IrDA options permit connection to sensors, operator interfaces, or service equipment. Designers should budget regulator headroom, isolate switching-node routing, and test startup and fault behavior across the full 3 V to 3.6 V supply range.
Önerilen
Motor-Control Education Platforms
The PIC24FJ16MC102-I/SO is well suited to educational motor-control platforms because it exposes a 16-bit architecture, MCPWM peripherals, CTMU, PPS, and multiple serial interfaces within a 28-pin SOIC package. The 16 MIPS processing rate allows students to observe control-loop timing and peripheral remapping without working with a large pin-count microcontroller. Microchip's related dsPICDEM MCHV and MCLV development-board documentation provides a reference for evaluating the device family. A laboratory implementation should begin with the manufacturer example configuration, then add feedback sensing and protection only after basic PWM operation is stable.
Önerilen
Embedded Sensing and Control
The PIC24FJ16MC102-I/SO can serve as a compact mixed-sensing controller when a motor or actuator must operate alongside capacitive inputs, communications, and local logic. CTMU provides a dedicated capacitive-measurement resource, while the 16-bit CPU at 16 MIPS can combine measurements with control updates and serial protocols. Its 1 KB RAM is sufficient for short control buffers, although designers should evaluate data lifetime for larger acquisition workloads. PPS reduces routing constraints for supported peripherals, but every multiplexed assignment must be checked against the 28-pin device configuration before the board layout is released.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: PIC24FJ16MC102-I/SO — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | PIC24FJ16MC102-E/SO |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 28-pin SOIC | 28-pin SOIC - same footprint |
| Architecture | 16-bit | 16-bit |
| CPU Performance | 16 MIPS | 16 MIPS |
| Program Memory | 16 KB Flash | 16 KB Flash |
| Data Memory | 1 KB RAM | 1 KB RAM |
| Motor-Control PWM | MCPWM peripheral | MCPWM peripheral |
| Capacitive Touch | CTMU peripheral | CTMU peripheral |
| Peripheral Routing | Peripheral Pin Select (PPS) | Peripheral Pin Select (PPS) |
| Temperature-Grade Code | I - industrial temperature | E - extended temperature |
Ana Farklılayıcılar
- Matches the established industrial-temperature motor-control configuration (karşılaştırma:PIC24FJ16MC102-E/SO)
- Combines motor-control and capacitive-measurement resources (karşılaştırma:PIC24FJ16MC102-E/SO)
- Supports five named serial-interface families (karşılaştırma:PIC24FJ16MC102-E/SO)
Tasarım Notları
Resolve PPS assignments before fixing the PCB layout because the MCPWM, communication, and general-purpose functions can share package pins. Create a pin-allocation table that identifies the owner, alternate functions, and electrical direction of every connected signal. Place the MCU close to its decoupling capacitors and keep traces to power-stage switching nodes as short as possible. The manufacturer data-sheet pin-description table is the controlling reference for supported assignments.
Design the 3.3 V rail to remain between 3 V and 3.6 V under motor-startup and maximum-load conditions. A motor controller can draw repeated current transients from its supply, so the regulator and local decoupling network must not pull the MCU rail below its operating limit. Use the manufacturer recommended capacitor values and placement near the supply pins, and evaluate the power path with the highest switching activity rather than only the idle operating condition.
Separate the sensitive MCU and CTMU circuitry from motor-drive power paths, high-current return conductors, and switching-node copper. Route communication signals away from the motor stage and use a continuous ground reference under the MCU where the layout rules permit. CTMU measurements can be sensitive to capacitance and leakage, so keep sensor traces short and clean and validate the layout with the manufacturer's capacitive-measurement guidance.
Do not treat PIC24FJ16MC102-I/SO and PIC24FJ16MC102-E/SO as interchangeable without checking environmental requirements. Their footprint and primary electrical specifications align, but the I and E order codes denote different temperature grades. Confirm the exact suffix, operating-temperature range, pin configuration, and programmed peripheral behavior before production release. Also avoid selecting related family members solely by flash and RAM size because pin multiplexing and peripheral assignments can differ.
Uyumluluk Bilgisi
RoHS compliance is identified for the exact PIC24FJ16MC102-I/SO order code. No additional REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were available.