SI3210-GTR - 3.3V/5V Single-Channel SLIC | Skyworks
MPN: SI3210-GTR ✓ AktifSI3210-GTR Genel Bakış
A SLIC is the analog interface between a telephone line and a digital voice system. The larger category hierarchy is SLIC → subscriber line interface circuit → voice-access IC → telecom interface IC → semiconductor. By combining line termination, voice conversion, and battery-generation support in one programmable device, the SI3210-GTR simplifies the hardware required for a single analog phone channel while retaining digital control from a host processor.
The SI3210-GTR supports 3.3 V and 5 V operation and is identified as a one-channel SLIC/CODEC. Its stated 60 dB performance figure and 41 mA operating-current specification make it relevant to compact voice interfaces where supply compatibility and line-channel performance matter. PCM connectivity supports transport of digital voice samples, while SPI access supports configuration and control from an embedded controller.
The ProSLIC architecture implements a programmable CMOS SLIC and CODEC in one device. The SI3210 version integrates battery generation, whereas the closely related SI3211 architecture provides battery selection. That distinction is important when designing a new telephone interface because the required external line-support network and firmware configuration can differ even when the family-level voice functions are similar.
Typical uses include analog adapters, voice-over-PoE gateways, customer premise equipment, embedded voice recorders, and industrial telephone extensions. A system designer can use the integrated CODEC to reduce the number of separate analog-to-digital and digital-to-analog conversion blocks while retaining a programmable line interface.
The principal design consideration is line-network compatibility. The SLIC must be paired with appropriate external protection, coupling, and battery-support components, and its firmware configuration must match the intended line impedance and country-specific ringing plan. PCB layout should preserve clean separation between sensitive voice signals, digital control traces, and switching or power-supply nodes.
This page combines device specifications, lifecycle and sourcing information, drop-in family alternatives, parameter comparisons, and application-focused design guidance. It also highlights the difference between programmable SLIC functionality and a basic codec so engineers can evaluate signal-chain completeness before committing a board layout.
Drop-in alternatifler için SI3210-GTR — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller SI3210-GTR (aynı form faktörü ve ayağa oturma) — farklı olan Package, Channel Count, Device Type, Supply Voltage, Battery Voltage Generation.
SI3210-GT
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →SI3210-FT
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →SI3210-KT
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →SI3211-GT
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
SI3211-KT
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →SI3210-GTR Özellikler
| Product Type | Single-channel SLIC and voice CODEC |
| Number of Channels | 1 channel |
| Besleme Gerilimi | 3.3 V or 5 V |
| Operating Current | 41 mA |
| Line Performance | 60 dB |
| Digital Interface | PCM and SPI |
| Paket | 38-pin TSSOP |
| Packaging | Tape and reel |
| Montaj Türü | Surface mount |
| Minimum Supply Voltage | 3.13 V |
| Maximum Supply Voltage | 5.25 V |
| Minimum Operating Temperature | 0 C |
| Battery Function | Battery generation |
| Codec Architecture | Programmable CMOS SLIC/CODEC |
| Target Application | Analog telephone customer premise equipment |
SI3210-GTR 38-pin tssop Pin Yapısı Kılavuzu
SI3210-GTR (38-pin tssop paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: SI3210-GTR.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
SI3210-GTR için uygundur 6 uygulamas: Analog Voice Gateway, Customer Premise Equipment, Voice-Over-PoE Terminal, Industrial Telephone Extension, Embedded Voice Recorder, VoIP Fax Bridge.
Analog Voice Gateway
The SI3210-GTR fits an analog telephone gateway because it combines a one-channel SLIC, voice CODEC, and battery-generation function in a single 38-pin TSSOP device. Its 3.3 V or 5 V operating range allows the same interface section to serve legacy 5 V logic systems or lower-voltage embedded platforms, while PCM transfers voice samples to a digital processor. The stated 60 dB line performance provides a defined starting point for voice-channel design. Using the integrated codec reduces the number of external conversion blocks, but the line network, protection components, ringing plan, and firmware calibration must still match the target telephone line.
Önerilen
Customer Premise Equipment
Customer premise equipment requires a compact interface between an analog subscriber line and the equipment's digital voice-processing path. The SI3210-GTR provides that function in one programmable CMOS device, combining the SLIC, CODEC, and battery generation while exposing PCM and SPI connectivity. Its single-channel architecture is appropriate for one-line fax, voice terminal, or analog adapter designs, and its 3.3 V or 5 V supply flexibility simplifies adaptation to different host systems. The 38-pin TSSOP package supports surface-mount production, although correct thermal pad layout, line-impedance configuration, and external protection remain essential.
Önerilen
Voice-Over-PoE Terminal
A voice-over-PoE terminal can use the SI3210-GTR to add an analog telephone port alongside packetized voice service. The integrated one-channel SLIC and CODEC handles the analog line interface, while PCM provides a conventional digital voice path to a communications processor and SPI permits configuration and control. Operating from 3.3 V or 5 V supports both lower-voltage and established 5 V system architectures, and the 60 dB stated performance is useful when establishing line-level design targets. The PoE supply must remain independent from the telephone-line battery requirements so switching-node noise does not degrade voice quality.
Önerilen
Industrial Telephone Extension
Industrial installations frequently combine an analog extension line with a digital controller for call routing, monitoring, or emergency communication. The SI3210-GTR provides the physical line and voice-conversion interface in one 38-pin TSSOP package, with 3.3 V or 5 V operation allowing integration into existing control electronics. Its 60 dB stated line characteristic provides a concrete design benchmark, and PCM/SPI connectivity supports both voice transport and register-level control. Because industrial environments may expose the line to larger transients, designers should pair the device with a properly engineered protection network rather than relying on the interface IC alone.
Önerilen
Embedded Voice Recorder
An embedded voice recorder can use the SI3210-GTR when it must accept an analog telephone line and deliver PCM audio to a digital processor. Integrating the SLIC and CODEC avoids a separate analog-to-digital converter, while the battery-generation function supports the line interface commonly required by analog telephones. The device accepts a 3.3 V or 5 V supply and communicates through PCM and SPI, enabling host control of line parameters and retrieval of voice data. The single-channel format is well matched to one recorded line, but the design must account for ringing, off-hook behavior, line-power demand, and the external passive network.
Önerilen
VoIP Fax Bridge
A VoIP fax bridge that must retain an analog fax endpoint can place the SI3210-GTR between the line and a packetized voice subsystem. Its one-channel SLIC and integrated CODEC support the required analog-to-digital conversion, while PCM provides a conventional interface to the bridge processor and SPI supports configuration and diagnostics. The 3.3 V or 5 V supply flexibility simplifies adaptation to processor and line-power architectures, and the 38-pin TSSOP package minimizes board area. Production validation should include line-state timing, tone handling, ringing cadence, and immunity to nearby switching supplies.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: SI3210-GTR — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | SI3210-GT | SI3210-FT | SI3210-KT | SI3211-GT | SI3211-KT |
|---|---|---|---|---|---|---|
| Brand | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions |
| Package | 38-pin TSSOP | 38-pin TSSOP - same | 38-pin TSSOP - same | 38-pin TSSOP - same | 38-pin TSSOP - same | 38-pin TSSOP - same |
| Product Type | SLIC and voice CODEC | Legacy SLIC | SLIC and voice CODEC | SLIC and voice CODEC | SLIC and voice CODEC | SLIC and voice CODEC |
| Battery Function | Battery generation | Battery generation | Battery generation | Battery generation | Battery selection | Battery selection |
| Digital Connectivity | PCM and SPI | PCM and SPI | PCM and SPI | PCM and SPI | PCM and SPI | PCM and SPI |
Ana Farklılayıcılar
- Integrated battery generation (karşılaştırma:SI3211-GT)
- Single-channel integration (karşılaştırma:SI3211-KT)
- Dual supply-voltage support (karşılaştırma:SI3210-GT)
- PCM and SPI host connectivity (karşılaştırma:SI3210-FT)
Tasarım Notları
Use the 38-pin TSSOP land pattern and exposed-pad geometry specified by the manufacturer package drawing. Place the device close to the subscriber-line network so that sensitive voice and battery nodes remain short, while routing PCM and SPI traces away from switching-regulator power paths. Maintain the recommended copper area beneath the thermal pad so junction heat can move into the PCB rather than concentrating around the fine-pitch leads.
The SLIC, codec, and battery functions share a sensitive analog telephone environment. Keep external line-network components close to the appropriate interface pins, provide a continuous ground reference beneath the analog section, and avoid routing the PCM clock and SPI signals alongside line and battery conductors. Validate ringing, off-hook, and voice distortion with the actual protection network because component placement can influence noise and impedance margins.
Design the 3.3 V or 5 V supply rail for the stated 41 mA operating current plus margin for digital load and transient behavior. Decoupling should follow the manufacturer application circuit, with local high-frequency bypass placed directly across the relevant supply pins. Keep the telephone-line battery network separate enough that ringing or off-hook transitions do not couple directly into sensitive codec supply nodes.
Do not select a suffix variant solely because it has the same 38-pin package. The SI3210 and SI3211 families differ in battery generation versus battery selection, and ordering suffixes can affect grade or packaging details. Verify pin assignments, supply limits, line-network topology, and the required register or firmware configuration against the manufacturer datasheet before releasing a replacement to production.
Uyumluluk Bilgisi
The device is a telecom interface IC rather than an automotive-qualified product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.