SN74LS540M - 8-Channel Inverting 3-State Buffer | Texas Instruments
MPN: SN74LS540M ✓ AktifSN74LS540M Genel Bakış
A logic buffer is a digital IC that receives a signal and reproduces it with the required voltage levels, current capability, isolation, or direction control. The SN74LS540 belongs to the broader hierarchy of bipolar logic ICs, including TTL-compatible logic, buffer/line-driver circuits, and digital interface components. Its 3-state outputs can be placed into a high-impedance state so several devices can share a bus without creating contention.
Key features include eight inverting channels, 3-state output control, a 4.75 V to 5.25 V supply range, and output drive capability specified for the LS logic family. The inverting function reverses the logic state at each channel, while the output-enable pin provides a common control for all eight channels. The 20-pin SOIC package is suitable for conventional through-hole-style surface-mount assembly and gives enough pin separation for straightforward PCB routing.
The SN74LS540 is designed around standard 74LS bipolar logic behavior rather than low-voltage CMOS. This makes it useful when a system already uses 5 V TTL or 74LS-family logic and needs buffering, bus isolation, or increased drive capability. The output-enable control is especially useful in multiplexed data paths, where only one section of a bus should actively drive the shared node while other sections are disabled.
Typical applications include instrument control, digital test equipment, industrial control interfaces, embedded peripheral bus isolation, and general-purpose logic fan-out. Because the outputs are 3-state devices, the SN74LS540 can support bus arbitration designs where multiple buffers connect to a shared conductor. Designers should still account for the enable-pin polarity and the timing relationship between data and output enable.
For PCB design, place the device close to the protected or shared bus and route the output-enable signal away from high-current switching nodes. Decoupling capacitors should be positioned close to the supply and ground pins. The supply rails must remain within the specified 4.75 V to 5.25 V range, and unused inputs should be held at a defined logic level rather than left floating.
This product page combines the SN74LS540M electrical identity, package and pin information with sourcing details, drop-in replacement guidance, and practical PCB implementation notes for engineers evaluating a 5 V 74LS-compatible bus buffer.
Drop-in alternatifler için SN74LS540M — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
SN74LS540M
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →74LS540M
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
SN74LS540DM
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
SN74LS540M
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →SN74LS540NSR
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
SN74LS540M Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | 8-channel inverting buffer and line driver |
| Number of Channels | 8 channels |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Logic Family | 74LS bipolar TTL logic |
| Çıkış Konfigürasyonu | 3-state, inverting |
| Output Enable | Common active-low output enable |
| Output Current | 50 mA |
| Input Current | 15 mA |
| İşletim Sıcaklığı Aralığı | 0°C to 70°C |
| Paket | 20-pin SOIC |
| Montaj Türü | Surface Mount |
| Logic Level | 5 V TTL/LS |
| Output Drive | 50 mA |
| Enable Input Type | Active-low, with Schmitt-trigger characteristics |
| RoHS Durumu | Compliant |
| REACH Status | Unknown |
| Automotive Qualification | Not applicable |
SN74LS540M Pin Yapısı
| Pin 1 | 1A — Data input for channel 1 |
| Pin 2 | 1Y — Inverting output for channel 1 |
| Pin 3 | 2A — Data input for channel 2 |
| Pin 4 | 2Y — Inverting output for channel 2 |
| Pin 5 | 3A — Data input for channel 3 |
| Pin 6 | 3Y — Inverting output for channel 3 |
| Pin 7 | 4A — Data input for channel 4 |
| Pin 8 | 4Y — Inverting output for channel 4 |
| Pin 9 | GND — Ground connection |
| Pin 10 | OE — Active-low output enable |
| Pin 11 | 8Y — Inverting output for channel 8 |
| Pin 12 | 8A — Data input for channel 8 |
| Pin 13 | 7Y — Inverting output for channel 7 |
| Pin 14 | 7A — Data input for channel 7 |
| Pin 15 | 6Y — Inverting output for channel 6 |
| Pin 16 | 6A — Data input for channel 6 |
| Pin 17 | 5Y — Inverting output for channel 5 |
| Pin 18 | 5A — Data input for channel 5 |
| Pin 19 | 4Y — Inverting output for channel 4 |
| Pin 20 | 4A — Data input for channel 4 |
Tipik Uygulamalar
SN74LS540M için uygundur 6 uygulamas: Shared Digital Bus Isolation, Instrument Control Interface, Industrial Control Logic, Peripheral Data Fan-Out, Embedded Peripheral Bus Interface, Digital Test and Measurement Fixture.
Shared Digital Bus Isolation
The SN74LS540M is appropriate for shared digital buses where several 5 V logic devices must be connected to one conductor without fighting for control of the node. Each of its eight channels provides an inverted 3-state output, and the common active-low output-enable input releases or enables the entire group at once. Place the buffer near the bus connector and keep the enable trace short, because long control paths can introduce timing skew between data and bus release. The 4.75 V to 5.25 V supply range matches standard 74LS systems, while the 50 mA output-drive rating supports conventional TTL fan-out and board-level logic loads.
Önerilen
Instrument Control Interface
In test and measurement instruments, control and status signals often travel from a controller card to a front-panel connector through long or electrically noisy paths. The SN74LS540M can buffer those lines while its 3-state outputs provide a controlled high-impedance state during bus handshakes. Its eight channels cover parallel command, mode, or acknowledgment signals, and the inverting logic can simplify polarity restoration at a receiver stage. The 20-pin SOIC package is compact enough for dense interface boards, but the design should preserve the 4.75 V to 5.25 V supply limits and account for the active-low enable timing when sequencing instruments.
Önerilen
Industrial Control Logic
The SN74LS540M can support 5 V industrial control boards that distribute buffered logic between a processor, peripheral cards, and field-interface logic. Its common 3-state output control is useful for card cages or backplanes where only one subsystem should actively drive a shared signal group at a time. The 74LS supply range and 0°C to 70°C commercial rating suit controlled indoor equipment, but protection against industrial transients must be added outside the IC. Designers should use the output-enable pin as a deliberate bus-management signal and verify timing against the receiving device rather than relying only on nominal propagation delay.
Önerilen
Peripheral Data Fan-Out
Use the SN74LS540M when a 5 V control signal must reach several destinations with improved drive capability or electrical isolation from the source. Eight parallel channels allow a byte-wide command or status bundle to be distributed without using eight separate discrete buffer packages. Because each channel is inverting, the receiving logic should be checked for complementary signal expectations; the output stages can be disabled when a destination is not selected. The SOIC-20 construction supports conventional surface-mount assembly, and the supply decoupling and enable routing should be designed as part of the fan-out network rather than treated as afterthought connections.
Önerilen
Embedded Peripheral Bus Interface
The SN74LS540M can isolate an embedded peripheral interface from a shared 5 V processor bus by presenting a controlled 3-state driver at the connector side. This arrangement helps prevent a peripheral card from driving the bus when it is inactive, while the common enable signal allows a simple card-level control scheme. The device is appropriate for legacy TTL systems where signal buffering and bus contention management are more important than low-voltage power consumption. Confirm the interface’s logic polarity, timing budget, and output load before installation, and use the manufacturer pinout to preserve the relationship between each input, output, enable, supply, and ground connection.
Önerilen
Digital Test and Measurement Fixture
A fixture or measurement interface can use the SN74LS540M to drive control lines from a tester toward connectorized circuitry while maintaining controlled bus states. The eight channels are useful for mode selection, relay-control strobes, and status handshakes, while the 3-state capability allows the tester to release a line when another fixture section takes control. The 4.75 V to 5.25 V operating range aligns with conventional TTL test equipment. For high-speed or long-line applications, check the datasheet propagation-delay and transition-time characteristics, provide local supply decoupling, and keep the common enable path free of noisy switching edges.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: SN74LS540M — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | SN74LS540M | 74LS540M | SN74LS540DM | SN74LS540M | SN74LS540NSR |
|---|---|---|---|---|---|---|
| Package | 20-pin SOIC | 20-pin SOIC | 20-pin SOIC | 20-pin SOIC | 20-pin SOIC | 20-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Motorola | Texas Instruments | onsemi | Texas Instruments |
| Channel Count | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Logic Function | Inverting | Inverting | Inverting | Inverting | Inverting | Inverting |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Output Enable | Common active-low enable | Common active-low enable | Common active-low enable | Common active-low enable | Common active-low enable | Common active-low enable |
| Output Current | 50 mA | 50 mA | 50 mA | 50 mA | 50 mA | 50 mA |
Ana Farklılayıcılar
- Provides eight parallel channels in a single logic package (karşılaştırma:74LS540M)
- Common 3-state output enable for bus management (karşılaştırma:SN74LS540NSR)
- Directly supports 5 V 74LS logic systems (karşılaştırma:SN74LS540DM)
Tasarım Notları
Keep the 74LS logic rail within 4.75 V to 5.25 V and place the local supply-decoupling capacitor close to the device supply and ground pins. The SN74LS540M is a bipolar 74LS-family device, so supply noise can affect output thresholds and bus timing. Provide a low-impedance return path, avoid sharing the return connection with high-current switching loops, and verify the design against the manufacturer recommended operating conditions.
Route the common output-enable signal with care because it controls all eight channels at once. Keep the enable trace short, separate from noisy clock and relay-driver nets, and add a pull resistor only when the system designer has confirmed the required inactive state. When several buffers share a bus, use non-overlapping enable timing so that one device begins driving only after the previous device has entered the high-impedance state.
Do not confuse the SN74LS540 with the SN74LS541: the SN74LS540 provides inverted outputs, while the SN74LS541 provides non-inverted outputs. Also check the exact suffix and package before substitution, because a similar logic function does not guarantee identical pin arrangement, temperature qualification, or shipping format. Use the manufacturer pin-description table and the 20-pin SOIC footprint on the existing board before approving a replacement.
Uyumluluk Bilgisi
The verified onsemi listing identifies the SN74LS540M as RoHS compliant. The commercial M suffix is listed at 0°C to 70°C; automotive qualification is not applicable to this ordering code. Other compliance attributes are unknown.