STM32F411RCT6 - 100MHz Cortex-M4 MCU 256KB | STMicroelectronics
MPN: STM32F411RCT6 ✓ AktifSTM32F411RCT6 Genel Bakış
What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O on one die. The STM32F411RCT6 sits in the hierarchy: Cortex-M4 -> Arm Cortex-M family -> 32-bit RISC processor -> microprocessor -> semiconductor IC. It functions as the active computational element in embedded systems, executing firmware stored in Flash while coordinating communication, sensing, and actuation through on-chip peripherals.
Key features include the FPU and DSP extensions, an 8 MHz internal RC oscillator, USB 2.0 Full-Speed OTG, up to 11 timers, three I2C, three SPI, three USART, one UART, plus a 12-bit ADC, SDIO, and a real-time clock. The Adaptive Real-Time (ART) Accelerator enables zero-wait-state execution from Flash, allowing the core to sustain 100 MHz throughput without instruction stalls.
A built-in voltage regulator and POR/PDR/PVD circuits reduce external components, while a 4-byte backup register and RTC domain with optional VBAT keep critical state across power-down cycles. The 64-pin LQFP exposes 50+ GPIO, expanding to multiple alternate functions for motor drive, display, and audio interfaces. Internal bus matrix (AHB/APB) connects the DMA controller (8-channel) to memory and peripherals, offloading data movement from the CPU.
Typical applications include consumer medical devices such as glucose meters and portable diagnostics, USB peripherals including HID mass-storage and CDC bridges, motor control for small BLDC and stepper drives, and home audio processing units. Industrial HMI panels and IoT sensor gateways also leverage the SRAM headroom and rich peripherals.
For design, ensure VDDA is tied to VDD or filtered separately when the ADC is in use; place the MCU's bypass network within 5 mm of each pair of supply pins. For USB designs the D+/D- traces must be 90 ohm differential and matched to within 150 mil.
This page synthesizes distributor stock, drop-in alternatives, pricing tiers, and PCB design notes to help procurement and embedded engineers evaluate STM32F411RCT6 alongside competing Cortex-M4 devices.
Drop-in alternatifler için STM32F411RCT6 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller STM32F411RCT6 (aynı form faktörü ve ayağa oturma) — farklı olan Package, Core, Timers, Flash Memory, Communication Interfaces.
STM32F401RCT6
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →STM32F405RGT6
✅ Yerleştirme✓ Stokta
$6.75 / Birim
Veri Şablonunu Görüntüle →STM32F415RGT6
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →STM32F103RCT6
✅ Yerleştirme✓ Stokta
$1.6406 / Birim
Veri Şablonunu Görüntüle →GD32F303RCT6
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
STM32F411RCT6 Maksimum Değerlendirmeler & Elektriksel Özellikler
| Core | ARM Cortex-M4 with FPU and DSP |
| Azami Saat Hızı | 100 MHz |
| Program Memory Size | 256 KB Flash |
| RAM Size | 128 KB SRAM |
| Supply Voltage Range | 1.7 V to 3.6 V |
| İşletim Sıcaklığı Aralığı | -40C to +85/105/125C |
| Paket | 64-LQFP (10x10 mm) |
| Montaj Türü | Surface Mount |
| GPIO Count | 50+ |
| ADC | 1x 12-bit, up to 2.4 MSPS |
| Timers | Up to 11 (including 1 SysTick) |
| Communication Interfaces | 3x I2C, 3x SPI, 3x USART, 1x UART, USB 2.0 FS OTG |
| DMA Channels | 8 |
| RoHS Durumu | Compliant |
STM32F411RCT6 Pin Yapısı
| Pin 1 | PC13 — GPIO/Tamper-RTC |
| Pin 2 | PC14/OSC32_IN — GPIO/LSE crystal input |
| Pin 3 | PC15/OSC32_OUT — GPIO/LSE crystal output |
| Pin 4 | VSS — Ground |
| Pin 5 | VDD — Digital supply voltage |
| Pin 6 | OSC_IN — HSE crystal input |
| Pin 7 | OSC_OUT — HSE crystal output |
| Pin 8 | BOOT0 — Boot mode select |
| Pin 9 | VREF+ — ADC reference (or VDD) |
| Pin 10 | PA0 — GPIO/UART4_TX/ADC_IN0 |
| Pin 11 | PA1 — GPIO/UART4_RX/ADC_IN1 |
| Pin 12 | PA2 — GPIO/USART2_TX/TIM5_CH3/ADC_IN2 |
| Pin 13 | PA3 — GPIO/USART2_RX/ADC_IN3 |
| Pin 14 | PA4 — GPIO/SPI1_NSS/USART2_CK/ADC_IN4 |
| Pin 15 | PA5 — GPIO/SPI1_SCK/ADC_IN5 |
| Pin 16 | PA6 — GPIO/SPI1_MISO/TIM3_CH1/ADC_IN6 |
| Pin 17 | PA7 — GPIO/SPI1_MOSI/TIM3_CH2/ADC_IN7 |
| Pin 18 | PB0 — GPIO/ADC_IN8/TIM3_CH3 |
| Pin 19 | PB1 — GPIO/ADC_IN9/TIM3_CH4 |
| Pin 20 | PB2/BOOT1 — GPIO/Boot mode select |
| Pin 21 | PB10 — GPIO/I2C2_SCL/USART3_TX |
| Pin 22 | PB11 — GPIO/I2C2_SDA/USART3_RX |
| Pin 23 | VSS — Ground |
| Pin 24 | VDD — Digital supply voltage |
| Pin 25 | PB12 — GPIO/SPI2_NSS/I2C2_SMBA |
| Pin 26 | PB13 — GPIO/SPI2_SCK/TIM1_CH1N |
| Pin 27 | PB14 — GPIO/SPI2_MISO/TIM1_CH2N |
| Pin 28 | PB15 — GPIO/SPI2_MOSI/TIM1_CH3N |
| Pin 29 | PA8 — GPIO/USART1_CK/TIM1_CH1/MCO1 |
| Pin 30 | PA9 — GPIO/USART1_TX/TIM1_CH2 |
| Pin 31 | PA10 — GPIO/USART1_RX/TIM1_CH3 |
| Pin 32 | PA11 — GPIO/USB_DM/CAN_RX |
| Pin 33 | PA12 — GPIO/USB_DP/CAN_TX |
| Pin 34 | PA13/JTMS — GPIO/SWDIO |
| Pin 35 | VSS — Ground |
| Pin 36 | VDD — Digital supply voltage |
| Pin 37 | PA14/JTCK — GPIO/SWCLK |
| Pin 38 | PA15/JTDI — GPIO/SPI3_NSS/TIM2_CH1_ETR |
| Pin 39 | PB3/JTDO — GPIO/SPI3_SCK/TIM2_CH2 |
| Pin 40 | PB4/NJTRST — GPIO/SPI3_MISO |
| Pin 41 | PB5 — GPIO/I2C1_SMBA/SPI3_MOSI |
| Pin 42 | PB6 — GPIO/I2C1_SCL/USART1_TX |
| Pin 43 | PB7 — GPIO/I2C1_SDA/USART1_RX |
| Pin 44 | BOOT0 — Boot0 redundant bond (pull state) |
| Pin 45 | PB8 — GPIO/I2C1_SCL/TIM4_CH3 |
| Pin 46 | PB9 — GPIO/I2C1_SDA/TIM4_CH4 |
| Pin 47 | VSS — Ground |
| Pin 48 | VDD — Digital supply voltage |
| Pin 49 | PB14 — GPIO/SPI2_MISO/TIM1_CH2N (alt bond) |
| Pin 50 | PA0 — GPIO/WKUP/UART4_TX (alt bond) |
| Pin 51 | PC0 — GPIO/ADC_IN10 |
| Pin 52 | PC1 — GPIO/ADC_IN11 |
| Pin 53 | PC2 — GPIO/SPI2_MISO/ADC_IN12 |
| Pin 54 | PC3 — GPIO/SPI2_MOSI/ADC_IN13 |
| Pin 55 | VREFSD+/VSSA — ADC supply/ground |
| Pin 56 | VDDA — Analog supply voltage |
| Pin 57 | PA4 — GPIO alt bond |
| Pin 58 | PC4 — GPIO/ADC_IN14 |
| Pin 59 | PC5 — GPIO/ADC_IN15 |
| Pin 60 | PB0 — GPIO alt bond |
| Pin 61 | PB1 — GPIO alt bond |
| Pin 62 | PB2 — GPIO alt bond |
| Pin 63 | VSS — Ground |
| Pin 64 | VDD — Digital supply voltage |
Tipik Uygulamalar
STM32F411RCT6 için uygundur 6 uygulamas: USB HID / CDC Peripheral Devices, Industrial Sensor Hubs, Portable Consumer Medical Devices, Small BLDC / Stepper Motor Control, IoT Edge Gateways and Hubs, Audio Processing and Synthesizers.
USB HID / CDC Peripheral Devices
The STM32F411RCT6 is ideal for USB Human-Interface Device and Communication Device Class bridges because its integrated USB 2.0 Full-Speed On-The-Go controller plus 4 KB endpoint SRAM eliminates the need for an external PHY. With 128 KB of on-chip SRAM, the part comfortably runs CDC-ACM plus HID stacks concurrently without external memory. Core0 (M4 with FPU) executes firmware at zero-wait-state 100 MHz via the ART accelerator, leaving headroom for enumeration and protocol handling in real time. Place the MCU within 25 mm of the USB connector and route D+/D- as a 90-ohm differential pair.
Önerilen
Industrial Sensor Hubs
The STM32F411RCT6 aggregates analog and digital sensor data via its 12-bit ADC (up to 2.4 MSPS) and multi-protocol serial interfaces, then forwards it over USB, SPI, or USART. With 256 KB Flash and 128 KB SRAM, complex sensor-fusion and FFT routines can run locally at 100 MHz without DMA contention. According to the STM32F411 datasheet, three I2C and three SPI buses allow fan-out to multiple sensors simultaneously. The wide -40C to +85C/105C/125C temperature range suits outdoor enclosures.
Önerilen
Portable Consumer Medical Devices
The STM32F411RCT6 fits battery-powered medical electronics: its 1.7-3.6 V supply window accepts a Li-Ion cell directly, and the integrated DMA controller (8 channels) lets the ADC scan multiple channels independently of the CPU. Low-power Run and Stop modes (a hallmark of the F4 Dynamic Efficiency line) extend battery life on standby. The single-precision FPU accelerates FIR/IIR filters used in heart-rate or pulse-oximetry algorithms.
Önerilen
Small BLDC / Stepper Motor Control
The STM32F411RCT6 supports 6-step or field-oriented control of small brushless DC and stepper motors through its up to 11 timers (including one 16-bit advanced timer with complementary PWM and dead-band generation). The Cortex-M4 FPU executes Clarke/Park transforms in single-cycle precision. With 256 KB Flash, advanced commutation algorithms and SoC estimators fit comfortably. STM32CubeMX makes pin-mux configuration straightforward for 3-shunt current sensing and Hall/encoder feedback inputs.
Önerilen
IoT Edge Gateways and Hubs
The STM32F411RCT6 makes a low-power edge node: connect to Wi-Fi or BLE modules via USART/SPI, run edge analytics in 128 KB SRAM, and bridge to upstream busses. The ART accelerator keeps STM32CubeMX-generated initialization overhead below 2 percent of CPU bandwidth, leaving the M4 to run modbus or MQTT-SN clients. USB OTG dual-role enables firmware upgrades via USB stick in the field, reducing service costs.
Önerilen
Audio Processing and Synthesizers
The STM32F411RCT6 is well-suited to low-cost audio products: its Cortex-M4 FPU plus DSP instructions accelerate MP3 decode, time-domain effects, or FIR equalization without external DSP hardware. Pair the MCU's I2S peripheral with an external codec such as the PCM5102APWR for 24-bit stereo output. With 256 KB Flash, code-fitting algorithms and wavetables for synthesis fit comfortably; USB MIDI can be added for no extra silicon via the integrated OTG controller.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: STM32F411RCT6 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | STM32F401RCT6 | STM32F405RGT6 | STM32F415RGT6 | STM32F103RCT6 | GD32F303RCT6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | GigaDevice |
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) |
| Core | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M4 with FPU | ARM Cortex-M3 (no FPU) | ARM Cortex-M4 with FPU |
| Maximum Clock Frequency | 100 MHz | 84 MHz | 168 MHz | 168 MHz | 72 MHz | 120 MHz |
| Flash Memory | 256 KB | 256 KB | 1 MB | 1 MB | 256 KB | 256 KB |
| SRAM | 128 KB | 64 KB | 192 KB | 192 KB | 48 KB | 48 KB |
| Supply Voltage | 1.7 V to 3.6 V | 1.7 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.0 V to 3.6 V | 2.6 V to 3.6 V |
| USB | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed OTG | USB 2.0 Full-Speed + High-Speed OTG | USB 2.0 Full-Speed + High-Speed OTG | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device |
Ana Farklılayıcılar
- Highest SRAM headroom at this clock rating (karşılaştırma:STM32F401RCT6)
- Cortex-M4 with FPU versus older M3 (karşılaştırma:STM32F103RCT6)
- Dual-role USB OTG at lower price than F4+ family (karşılaştırma:STM32F405RGT6)
- Cross-brand parity at lower cost (karşılaştırma:GD32F303RCT6)
Tasarım Notları
The STM32F411RCT6 requires a 100 nF decoupling capacitor on each VDD pin pair within 5 mm of the package. Per ST's hardware design guide (AN4321), place one bulk 4.7 uF capacitor per VDD cluster. VREF+ should be tied directly to VDDA via a ferrite bead when using the ADC, otherwise noise on VDDA degrades ADC performance.
USB D+/D- traces must be routed as a 90-ohm differential pair with matched length tolerance of 150 mil. According to ST's hardware layout guidelines, route the pair as short as possible, maintain spacing to ground copper > 7 mil, and avoid the proximity of high-frequency nets such as SDIO clock. The MCU itself should sit within 25 mm of the USB connector.
Place the 8 MHz HSE crystal and its 20 pF load capacitors within 5 mm of OSC_IN and OSC_OUT. Use a guard ground around the crystal to suppress coupling from adjacent clocks. Per the STM32F411 reference design, configure the crystal's trace width to 12 mil and match the load capacitor location symmetrically. Boot pins BOOT0 and PB2/BOOT1 must be pulled to known state with 100 kohm resistors to ground.
A frequent mistake is powering the chip down without putting PA13/SWDIO and PA14/SWCLK in a defined state - leaving them floating can cause unintentional reset in the next power-up. Per AN2586, both debugger pins require either a 100 kohm pull-up to VDD or a 100 kohm pull-down to ground. Also, when using the BOOT0 pin, a noise spike below 50 ns can induce bootloader-mode entry.
Estimated: at maximum core activity (100 MHz, all peripherals clocked, M4 DSP instructions), the STM32F411RCT6 dissipates approximately 200 mW. The LQFP-64 has a typical theta_JA of 50 C/W on a 2-layer board with copper pour, so worst-case junction temperature rise is 10C above ambient. For industrial (+85C) applications, derate sustained peripheral activity at high temperatures. The internal thermal sensor (not provided in this part) should be substituted with external RTDs for precision protection.
Uyumluluk Bilgisi
RoHS compliant per ST product page. Consumer/industrial part - not AEC-Q100 qualified.
