SY89429AZC - 400MHz Programmable Clock Synthesizer | Microchip
MPN: SY89429AZC ✓ AktifSY89429AZC Genel Bakış
A programmable frequency synthesizer generates one or more clock signals from a controlled internal reference. Within the clock and timing hierarchy, it sits above a crystal oscillator and below the clock-distribution circuits used by processors, transceivers, converters, and test equipment. Its synthesized architecture allows the output frequency to be set through an external controller rather than remaining fixed at the reference frequency.
The SY89429AZC provides a serial three-wire programming interface and a parallel interface for power-on configuration. According to the Micrel Semiconductor data sheet, the serial interface uses a 14-bit shift register, while S_CLOCK shifts data on each rising edge and S_LOAD captures the configuration on its HIGH-to-LOW transition. An internal quartz reference supports autonomous clock generation without requiring an external frequency reference.
Output performance is centered on low jitter. The differential PECL outputs reach a peak-to-peak jitter of ±25 ps at 400 MHz, making the device suitable for timing systems requiring precise edge placement. The synthesizer also features minimal frequency overshoot, an important behavior for avoiding transient frequency excursions during frequency transitions or clock startup.
The device is suited to communication equipment, high-speed digital systems, data converters, test and measurement instrumentation, and clock-generation subsystems. Differential PECL outputs can feed line receivers or downstream clock buffers, while programmable operation permits different frequencies to be selected for multiple board-level timing requirements. The 28-SOIC package supports conventional surface-mount assembly.
Designers should use the complete pin-description and connection tables in the Microchip data sheet when assigning tracks and selecting interface termination. Differential output routing should be short and impedance-controlled, and unused inputs should be handled according to the device recommendations. Programming signals and clock outputs should be separated from sensitive analog paths to reduce coupling.
This page combines the device's documented frequency, interface, jitter, output, package, and compliance characteristics with engineering guidance for programming, layout, signal integrity, and sourcing. It also distinguishes exact catalog information from parameters that require confirmation against the manufacturer data sheet before a production design is released.
Drop-in alternatifler için SY89429AZC — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu ürüne yer değiştirme seçenekleri mevcut değil.
Alternatifleri Talep EdinSY89429AZC Özellikler
| Product Type | Programmable frequency synthesizer |
| Frequency Range | 25 MHz to 400 MHz |
| Azami Saat Hızı | 800 MHz |
| Çıkış Türü | Differential PECL |
| Output Jitter | ±25 ps peak-to-peak at 400 MHz |
| Frequency Overshoot | Minimal |
| Architecture | Synthesized |
| Serial Programming Interface | 3-wire serial interface |
| Serial Shift Register | 14 bit |
| Parallel Interface | Available for power-on configuration |
| Reference Source | Internal quartz reference |
| Paket | 28-SOIC, 7.50 mm width |
| Montaj Türü | Surface mount |
| RoHS Durumu | Non-compliant |
SY89429AZC 28-soic, 7.50 mm width Pin Yapısı Kılavuzu
SY89429AZC (28-soic, 7.50 mm width paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: SY89429AZC.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
SY89429AZC için uygundur 6 uygulamas: High-Speed Communication Clocking, Data Converter Clock Generation, Instrumentation and Test Equipment, Digital Clock-Distribution Hub, Industrial Control and Timing Subsystems, PCIe and Serial-Link Support Circuits.
High-Speed Communication Clocking
The SY89429AZC fits communication subsystems that require a programmable differential clock with low deterministic jitter. Its documented 25 MHz-to-400 MHz output range covers multiple clocking requirements, while ±25 ps peak-to-peak jitter at 400 MHz helps preserve edge timing through downstream receivers, retimers, or logic devices. The differential PECL outputs should be routed as a controlled-impedance pair, and the receiving circuit must be compatible with the device's output voltage levels. A programmable interface allows a controller to select the operating frequency during initialization or as part of an operating-mode change.
Data Converter Clock Generation
The SY89429AZC can supply a stable, programmable sampling clock to data-conversion systems where edge placement affects conversion timing. At 400 MHz, the documented peak-to-peak output jitter of ±25 ps provides a useful reference for timing-margin analysis, while the 25 MHz-to-400 MHz range allows the same synthesizer concept to serve multiple conversion rates. Differential PECL routing helps maintain signal integrity over the board. Designers must confirm that the converter's clock-input voltage, impedance, and jitter requirements match the synthesizer output and account for receiver or divider-added jitter.
Instrumentation and Test Equipment
Programmable clock generation is valuable in instrumentation and automated test systems that must exercise circuitry across different operating frequencies. The SY89429AZC supports output frequencies from 25 MHz through 400 MHz, allowing one synthesizer to serve multiple test profiles instead of relying on a fixed-frequency oscillator. Its low ±25 ps peak-to-peak jitter at 400 MHz supports precise stimulus timing, while differential PECL outputs can drive compatible receiver logic or clock-distribution stages. Firmware can adjust the synthesis configuration through the three-wire interface for automated test sequences.
Digital Clock-Distribution Hub
The SY89429AZC can act as the programmable source at the center of a clock-distribution hierarchy. Instead of distributing a fixed oscillator signal directly to multiple loads, the design can synthesize a chosen frequency and send it through buffered clock-tree stages. Differential PECL outputs support controlled routing to compatible receiver or buffer inputs, and the 400 MHz upper limit accommodates demanding digital logic domains. The implementation must preserve output-impedance continuity, provide suitable return paths, and observe the manufacturer pin and reference-circuit recommendations.
Industrial Control and Timing Subsystems
Industrial control electronics can use the SY89429AZC when multiple functional blocks require a programmable clock derived from a common internal quartz reference. Combining the reference, synthesizer, and programmable control reduces the number of independent oscillator arrangements that must be calibrated across a production board. The 25 MHz-to-400 MHz range accommodates logic, conversion, and communications clocking needs, while ±25 ps peak-to-peak jitter at 400 MHz supports precise timing at the upper operating limit. Isolation and signal-integrity requirements should be evaluated for each industrial environment.
PCIe and Serial-Link Support Circuits
The SY89429AZC may support auxiliary clocking in serial-link and high-speed interface systems when the required frequency lies within its 25 MHz-to-400 MHz programming range. Its differential PECL output and low jitter are useful for timing-critical service clocks or local synchronization networks, although the device is not itself a PCIe protocol controller. Use it only where its programmed frequency, output amplitude, and interface timing satisfy the surrounding circuit. Point-to-point routing, controlled reference planes, and careful return-path continuity are essential to preserve the specified output-jitter performance.
Mühendislik referans verileri: SY89429AZC — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün |
|---|---|
| Brand | Microchip Technology |
| Package | 28-SOIC, 7.50 mm width |
| Programmable Frequency Range | 25 MHz to 400 MHz |
| Maximum Clock Frequency | 800 MHz |
| Output Type | Differential PECL |
| Peak-to-Peak Output Jitter | ±25 ps at 400 MHz |
| Programming Interface | 3-wire serial and parallel power-on interface |
| Serial Shift Register | 14 bit |
| Reference | Internal quartz reference |
| Frequency Overshoot | Minimal |
| RoHS Status | Non-compliant |
Tasarım Notları
Route the differential PECL outputs as a compact, length-matched pair with a continuous reference plane beneath the pair. Keep the programming traces S_CLOCK, S_DATA, S_LOAD, and the parallel configuration inputs away from the clock outputs to reduce coupling into the edge-sensitive clock path. Follow the reference schematic and package pin table in the Micrel Semiconductor manufacturer data sheet for bypass-capacitor placement and grounding.
Confirm the output voltage levels and receiver thresholds before connecting the PECL outputs. Differential routing alone does not establish logic compatibility if the receiver expects another family or supply voltage. Use the manufacturer's AC parameters and application guidance to evaluate data edges, return paths, and termination. PCB fabrication constraints and receiver input capacitance should also be included in the edge-rate assessment.
Do not replace the complete pin-description table with a generic clock-generator pinout. The serial interface uses a 14-bit shift register and captures configuration on the specified S_LOAD transition, while parallel configuration serves a separate power-on role. Validate the controller command sequence against the manufacturer's timing diagrams and confirm all supply, ground, reference, and programming connections before programming the device.
Uyumluluk Bilgisi
RoHS non-compliant status comes from the SY89429AZC catalog listing. No current manufacturer declarations for REACH, halogen-free status, or conflict-minerals compliance were identified. The device is an industrial clock-generation IC rather than an automotive-qualified product.