Microchip Technology

SY89808LTG - 500 MHz 1:9 HSTL Fanout Buffer | Microchip

MPN: SY89808LTG ✓ Aktif
3.3 V Vdss 32-pin TQFP Package 500 MHz Speed
MOQ: 1 |

SY89808LTG Genel Bakış

The Microchip Technology SY89808LTG is a 3.3 V clock fanout buffer and level translator with nine differential HSTL output pairs, a maximum clock frequency of 500 MHz, and a 32-pin TQFP package. It accepts two clock or data inputs and provides nine outputs, creating a 2:9 fanout configuration with differential HSTL signaling compatible with 1.5 V receivers.

A clock buffer is an integrated circuit that reproduces and distributes a timing signal without imposing excessive loading on its source. Clock and digital logic ICs belong to the broader clock and timing semiconductor category, with applications in processor interfaces, network equipment, test systems, and high-speed digital control. Fanout buffers are especially useful when one source must feed several receivers while preserving edge timing, signal integrity, and electrical loading margins.

The SY89808LTG supports up to 500 MHz operation and includes a triple-buffered enable function. Its 3.3 V core supply operates separately from the 1.8 V output supply, allowing the output-stage voltage to be selected for HSTL-compatible interfaces while the internal circuitry operates from 3.3 V. The nine differential outputs provide a practical means of reducing sensitivity to common-mode noise and accommodating balanced clock distributions.

This device is intended for high-speed clock distribution, data translation, and point-to-point differential signaling. Its input and output stages divide the clock tree into multiple independently routed branches, helping each destination maintain controlled impedance and trace length. The triple-buffered enable function allows the downstream receivers to be placed into a controlled state when clock distribution is not required, which can simplify initialization and reduce unnecessary circuit activity.

Typical uses include high-speed processor clock trees, communications equipment, networking infrastructure, instrumentation, and industrial control systems. It is also suitable where a single clock must feed several chips across a board while maintaining a 500 MHz maximum operating rate. Designers should consider transmission-line behavior, receiver thresholds, clock jitter, and trace length matching when assigning the differential outputs.

Place the SY89808LTG so that each differential pair follows a continuous, impedance-controlled route to its destination. Keep the clock source connections short, maintain symmetry between positive and negative traces, and avoid introducing unnecessary stubs. Because clock quality degrades when rise time, reflections, and crosstalk are not controlled, PCB stackup and receiver requirements should be reviewed before fabrication.

This product page consolidates the manufacturer's principal clock, voltage, package, and signaling specifications with practical PCB guidance. It also distinguishes verified drop-in replacements from parts that merely share a similar clock-buffer function, helping engineers assess replacement risk before changing a released PCB design.

Drop-in alternatifler için SY89808LTG — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

SY89808LTG-TR

✅ Yerleştirme
📦 32-TQFP
Same 500 MHz 1:9 differential HSTL function, terminals, and 32-TQFP package; the ordering suffix changes tape-and-reel shipment configuration

📋 Katalogda Olmayan Referans Alternatifi

SY89808LTG Özellikler

Product Type Clock fanout buffer and translator
Input Configuration 2 inputs
Çıkış Konfigürasyonu 9 differential output pairs
Fanout Ratio 2:9
Azami Saat Hızı 500 MHz
Core Supply Voltage 3.3 V
Output Supply Voltage 1.8 V
Output Logic Standard Differential HSTL
HSTL Receiver Compatibility 1.5 V compatible
Enable Function Triple-buffered
Paket 32-pin TQFP
Montaj Türü Surface mount

SY89808LTG 32-pin tqfp Pin Yapısı Kılavuzu

SY89808LTG (32-pin tqfp paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

32-pin tqfp paket pin çizelgesi için SY89808LTG

Ayrıntılı pin çıkış verisi mevcut değil: SY89808LTG.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

SY89808LTG için uygundur 6 uygulamas: Processor Clock Distribution, Networking Equipment Clock Trees, Differential Signal Translation, High-Speed Test and Measurement Systems, Industrial Control and Data Acquisition, General-Purpose Differential Clock Fanout.

🖥️

Processor Clock Distribution

The SY89808LTG fits high-speed processor and digital-logic clock trees that require one timing source to feed multiple endpoints. According to the manufacturer datasheet, the device accepts two inputs, provides nine differential HSTL output pairs, and supports a maximum clock frequency of 500 MHz. Place it near the clock source, then route each branch as a controlled-impedance differential pair. The separate 3.3 V core and 1.8 V output supplies permit the core logic and output swing to use their documented voltage levels. Designers should confirm receiver thresholds, allowable clock skew, jitter, and branch-length tolerance for the target processor before release.

🌐

Networking Equipment Clock Trees

The SY89808LTG can distribute a high-speed differential clock across multiple sections of a networking or communications board. Its 2:9 configuration, nine differential HSTL output pairs, and 500 MHz maximum operating frequency are useful when several line cards, transceivers, or controller groups need a related timing reference. Each output should use a continuous impedance-controlled route, with matched lengths within the receiver system's allowed tolerance. Because fanout buffers can amplify timing-budget limitations rather than correct them, engineers should verify source jitter, output skew, receiver setup and hold requirements, and channel loss before assigning the device to a production topology.

🔧

Differential Signal Translation

The SY89808LTG also fits interface circuits that require differential HSTL translation and fanout rather than a simple single-ended clock copy. According to the manufacturer datasheet, the device uses a 3.3 V core supply and a separate 1.8 V output supply while producing nine 1.5 V-compatible differential output pairs. That architecture can help interface a clock or control signal to compatible receivers while isolating the source from fanout loading. Validate signal thresholds, edge rate, return loss, and termination at each destination because translator operation alone does not guarantee compliance with the complete system interface specification.

🔧

High-Speed Test and Measurement Systems

In test and measurement equipment, the SY89808LTG can distribute a clock to multiple acquisition, conversion, or synchronization sections. According to the manufacturer datasheet, its maximum clock frequency is 500 MHz and it provides nine differential HSTL output branches, allowing a compact clock tree to replace multiple repetitive driver stages. Use the triple-buffered enable function during initialization or test sequencing where supported by the system architecture. Precision instruments still require careful attention to clock jitter, deterministic and random noise, output skew, channel attenuation, and calibration; the buffer should be treated as a timing distribution element rather than a cure for an inaccurate source reference.

🏭

Industrial Control and Data Acquisition

The SY89808LTG is appropriate for industrial control and data-acquisition boards that need one clock to serve multiple digital engines while retaining differential signaling. According to the manufacturer datasheet, the device supports 500 MHz operation and offers a 2:9 topology with nine HSTL output pairs. Place the device near the source clock and isolate high-current switching regions to reduce coupled noise. Verify the industrial environment's temperature requirement, grounding strategy, isolation boundaries, and connector-driven edge degradation. If the system uses a lower clock rate, the enable function can help control downstream receiver state, but power-state timing must be checked against every attached integrated circuit.

⚡

General-Purpose Differential Clock Fanout

The SY89808LTG can serve as a general-purpose differential clock fanout when a board needs repeatable outputs rather than a single-ended multi-load clock net. According to the manufacturer datasheet, the 32-pin TQFP device delivers nine differential HSTL output pairs from two inputs, with a 3.3 V core and 1.8 V output supply architecture. Routing each output through matched transmission-line geometry helps preserve edge quality and reduce loading on the source. Establish the expected load, termination method, maximum operating frequency, and acceptable skew before layout because a nominally identical clock at the output pins can still produce different receiver results when channel lengths and losses vary.

What is the SY89808LTG and what does it do?
The SY89808LTG is a 3.3 V clock fanout buffer and translator that converts two inputs into nine differential HSTL output pairs. According to the manufacturer datasheet, the device supports operation up to 500 MHz, provides 1.5 V-compatible HSTL signaling, and uses a separate 1.8 V output supply. It is used to distribute one clock across several receivers while limiting source loading.
What are the key specifications of SY89808LTG that engineers should know?
The principal SY89808LTG specifications are a 2:9 input-to-output configuration, nine differential HSTL output pairs, a 500 MHz maximum clock frequency, a 3.3 V core supply, and a 1.8 V output supply. According to the manufacturer datasheet, the device also provides a triple-buffered enable function. These parameters define its suitability for high-speed, multi-branch differential clock distribution.
What is the maximum clock frequency of SY89808LTG?
The SY89808LTG supports a maximum clock frequency of 500 MHz. According to the manufacturer datasheet, this rating applies to its differential HSTL fanout-buffer operation with the specified core and output supplies. The usable system clock can still be lower when receiver timing limits, PCB loss, jitter budget, or voltage margins become the limiting constraints.
Where can I download the SY89808LTG datasheet PDF?
The SY89808LTG datasheet PDF is available from the manufacturer-oriented document listing linked on this product page. According to the manufacturer datasheet, the document describes the 32-pin TQFP device, its 2:9 fanout arrangement, differential HSTL outputs, 500 MHz maximum frequency, supply architecture, enable controls, and recommended application details. Use that document for the authoritative pin-description and timing tables.
Where can I find the SY89808LTG pinout?
The SY89808LTG pinout should be taken from the pin-description table in the manufacturer datasheet because no verified diagram appears in the product documentation listed here. According to the manufacturer datasheet, the device is packaged in a 32-pin TQFP. Assign PCB connections using the numbered package drawing and observe the exposed-pad requirements printed for the exact ordering code.
What supply voltages does SY89808LTG require?
The SY89808LTG uses a 3.3 V core supply and a separate 1.8 V output supply. According to the manufacturer datasheet, the separate output supply supports reduced-swing HSTL-compatible outputs while the internal core operates from 3.3 V. Both rails require appropriate bypass capacitance and clean distribution because core and output-stage behavior are tied to their respective supply conditions.
Is SY89808LTG suitable for high-speed clock distribution?
Yes, the SY89808LTG is suitable for high-speed clock distribution when the design stays within its documented electrical and timing limits. According to the manufacturer datasheet, the device provides a 500 MHz maximum clock frequency, nine differential HSTL output pairs, and independent 3.3 V core and 1.8 V output supplies. PCB routing, receiver thresholds, jitter, and skew must still be verified for the target system.
When should I choose SY89808LTG over another clock buffer?
Choose the SY89808LTG when the design needs one clock source distributed across as many as nine differential branches with HSTL-compatible levels. According to the manufacturer datasheet, its 500 MHz rating, 2:9 arrangement, and separate 3.3 V core and 1.8 V output supplies make it appropriate for high-speed fanout trees. Select another device when its output count, logic standard, supply voltage, timing, or package does not match the board.
Can a 1:9 HSTL buffer replace SY89808LTG?
A 1:9 HSTL buffer may be functionally close, but it should not be treated as a drop-in replacement without a full pin and parameter comparison. According to the manufacturer datasheet, the SY89808LTG accepts two inputs and produces nine differential output pairs. A true replacement must also match the 32-pin TQFP footprint, enable behavior, supply architecture, output levels, and 500 MHz operating requirement.
What can replace SY89808LTG on the same PCB?
No verified same-footprint drop-in replacement is established for the SY89808LTG. The manufacturer datasheet identifies a specific 32-pin TQFP device with two inputs, nine differential HSTL output pairs, a 500 MHz maximum frequency, and separate core and output supplies. Use the Request a Quote form on this page to request the current part and compatible replacement review for a released design.
Is there a Microchip equivalent for SY89808LTG?
The SY89808LTG itself is a Microchip Technology clock fanout buffer and level translator, originally associated with Micrel semiconductor products. According to the manufacturer datasheet, its defining requirements are the 2:9 arrangement, nine differential HSTL outputs, 500 MHz maximum frequency, and 32-pin TQFP package. Microchip’s cross-reference service can confirm whether any newer family member preserves the complete footprint and timing behavior.
What is the difference between 2:9 and 1:9 fanout terminology?
The SY89808LTG is described as a 2:9 clock fanout buffer with two inputs and nine differential output pairs. According to the manufacturer datasheet, the device is also presented as a 1:9 differential HSTL fanout configuration for its primary distribution path. Both descriptions emphasize one clock distributed to nine outputs, but the pin-level design must be confirmed before treating differently labeled parts as interchangeable.
Where can I buy SY89808LTG online?
The SY89808LTG can be requested through the Request a Quote form on this page. According to the manufacturer datasheet, the part is a 3.3 V, 500 MHz, 2:9 differential HSTL fanout buffer in a 32-pin TQFP package. When requesting a quotation, include the required quantity, reel or tray preference, target delivery date, and any required traceability documentation.
What is the price of SY89808LTG?
Current commercial terms for the SY89808LTG should be obtained through the Request a Quote form on this page rather than from a static price statement. According to the manufacturer datasheet, the part is the 3.3 V, 500 MHz, 2:9 differential HSTL buffer in a 32-pin TQFP package. Submit the required quantity and packaging preference so a current quotation can be prepared.
What is the lead time and stock status for SY89808LTG?
The current lead time and stock status for SY89808LTG should be confirmed through the Request a Quote form on this page. According to the manufacturer datasheet, the identified device is the Microchip 3.3 V, 500 MHz, 2:9 differential HSTL fanout buffer in a 32-pin TQFP package. Include quantity, target date, and packaging requirements in the request to obtain an actionable schedule.
What PCB layout practices are important for SY89808LTG?
Use controlled-impedance, impedance-matched routing for every differential output and keep positive and negative traces coupled and length balanced. According to the manufacturer datasheet, the device provides nine differential HSTL output pairs, so branch stubs and unnecessary impedance discontinuities can directly affect timing and noise. Follow the application circuit and layout guidance in the manufacturer document, and include the package thermal and exposed-pad requirements in the board stackup.

Mühendislik referans verileri: SY89808LTG — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the SY89808LTG when a clock tree must distribute a signal to nine differential HSTL destinations and operate at frequencies up to 500 MHz. Its two inputs, nine differential output pairs, triple-buffered enable, and separate 3.3 V core and 1.8 V output supplies are the principal selection criteria. Confirm that every receiver supports the resulting levels and timing, and that the PCB can maintain controlled-impedance routing across all nine branches. Do not substitute a superficially similar 1:9 buffer unless it preserves the 32-pin TQFP footprint, enable behavior, supply architecture, output standards, and relevant timing limits. For designs requiring a different logic standard, output count, package, or supply voltage, evaluate a dedicated device from the required interface family rather than treating it as a drop-in replacement. Before placing an order for a new or revised design, review the manufacturer datasheet for the complete pin table, electrical characteristics, package drawing, and recommended application circuit.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün
Manufacturer Microchip Technology
Package 32-pin TQFP
Product Type Clock fanout buffer and translator
Input Configuration 2 inputs
Output Configuration 9 differential output pairs
Fanout Ratio 2:9
Maximum Clock Frequency 500 MHz
Core Supply Voltage 3.3 V
Output Supply Voltage 1.8 V
Output Logic Standard Differential HSTL
Enable Function Triple-buffered

Tasarım Notları

Route each differential output as a coupled, controlled-impedance pair and maintain symmetry between the positive and negative traces. Avoid stubs, unmatched branch transitions, and changes in reference-plane geometry that could increase reflections. The nine output branches should be planned independently so their loss, length, and termination characteristics remain compatible with the receiver timing budget.

Validate clock-edge degradation from source to receiver rather than relying only on the nominal 500 MHz operating limit. Include channel loss, receiver threshold, clock-jitter, output-skew, and timing-margin effects in simulation or measurement. Differential routing reduces susceptibility to common-mode noise but does not remove the need to control return paths, impedance discontinuities, and pair-length mismatch.

Provide the 3.3 V core and 1.8 V output rails as separate, cleanly decoupled supplies. Place bypass capacitors close to the corresponding supply and ground pins using the manufacturer application layout, and verify startup sequencing if the triple-buffered enable is controlled. Do not assume that the output rail can safely operate from the core rail or that both rails may ramp in any order without checking the device requirements.

Use the 32-pin TQFP land pattern, exposed-pad treatment, and soldering profile specified for the exact Microchip ordering code. The absence of a verified public pin diagram in the available documentation requires the manufacturer pin-description table and package drawing to remain the authoritative references for PCB routing and assembly.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is identified in the available product documentation.

Veri doğrulanma tarihi: 2026-11-10 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

SY89808LTG SY89808LTG datasheet SY89808LTG datasheet pdf SY89808LTG pinout Microchip SY89808LTG SY89808LTG 500 MHz SY89808LTG 1:9 HSTL SY89808LTG 32 TQFP SY89808LTG clock buffer SY89808LTG drop-in replacement SY89808LTG equivalent SY89808LTG price SY89808LTG stock SY89808LTG application circuit SY89808LTG TQFP pinout

İlgili Bileşenler ve Terimler

Microchip Technology SY89808LTG Micrel Semiconductor clock fanout buffer clock buffer level translator clock and timing IC integrated circuit semiconductor HSTL differential HSTL 2:9 fanout 500 MHz clock 3.3 V core supply 1.8 V output supply triple-buffered enable 32-pin TQFP TQFP package family surface-mount package differential pair controlled impedance clock jitter output skew signal integrity PCB layout
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle