onsemi

TCA0372DP1G - 1A Dual Power Op Amp | onsemi

MPN: TCA0372DP1G ✗ Son Kullanım Zamanı
5 V to 40 V Vdss 1.0 A Id 8-pin PDIP Package
MOQ: 1 |

TCA0372DP1G Genel Bakış

The onsemi TCA0372DP1G is a dual monolithic power operational amplifier capable of delivering 1.0 A output current from a 5 V to 40 V supply in an 8-pin PDIP package. The device provides two power operational-amplifier channels, a unity-gain bandwidth of 1.4 MHz, a nominal common-mode rejection ratio of 90 dB, and an input offset voltage as high as 20 mV. Its extended-temperature grade supports applications beyond the standard commercial temperature range.

A power operational amplifier is a voltage-controlled amplifier that combines the high input impedance and closed-loop control of an ordinary operational amplifier with substantially greater output-current capability. Within the power-management and signal-chain hierarchy, the TCA0372 belongs to the amplifier IC family and is commonly used where a low-level error or control signal must directly drive a coil, motor winding, speaker, or power-supply output stage.

The TCA0372's 1.0 A output-current capability makes it suitable for servo amplifiers, regulated power supplies, and industrial actuator drivers. Its no-dead-band crossover-distortion characteristic improves drive into inductive coils compared with solutions exhibiting an output transition dead zone. The two independent channels also permit mirrored, complementary, or dual-axis motion-control architectures while preserving identical amplifier characteristics.

The monolithic dual-amplifier design simplifies system implementation by placing two power op-amp channels in one package. The 1.4 MHz unity-gain bandwidth supports applications that require both low-frequency loop control and useful bandwidth for dynamic feedback systems. The 90 dB nominal common-mode rejection ratio helps isolate the input stage from common-mode disturbances, while the 20 mV maximum input offset voltage defines the practical DC error boundary that must be considered in precision servo loops.

Typical uses include servo-motor control, audio output stages, power-supply regulation, industrial positioning systems, and actuator drivers. Two amplifiers in one PDIP package can reduce board area when a system requires dual-axis control or complementary drive. Where the load is inductive, flyback current must be controlled with an external clamp path, and where the load is capacitive, stability must be checked using the feedback network and load conditions.

The primary design tradeoff is sustained output-current capability versus heat generated inside the 8-pin PDIP package. A 1.0 A rating does not imply that every load condition can be driven continuously without thermal analysis. Verify copper area, ambient temperature, output duty cycle, voltage headroom, and required safety margin before using the full current rating. Follow the onsemi datasheet for recommended compensation, bias-pin bypass, and application-circuit details.

This page organizes the key electrical limits, application guidance, drop-in candidates, and package-level design considerations for engineers evaluating the TCA0372DP1G in dual power-amplifier systems.

Drop-in alternatifler için TCA0372DP1G — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller TCA0372DP1G (aynı form faktörü ve ayağa oturma) — farklı olan Package, Maximum Output Current, Crossover Distortion, Mounting Type, Amplifier Type.

onsemi
Package: 8-PDIP, 8 pins
Maximum Output Current: 1.0 A per channel
Crossover Distortion: No deadband crossover distortion
İle Karşılaştır TCA0372DP1G →
onsemi
Package: 8-PDIP
Crossover Distortion: No deadband crossover distortion
Mounting Type: Through-hole
İle Karşılaştır TCA0372DP1G →
onsemi
Package: PDIP-8
Mounting Type: Through-hole
İle Karşılaştır TCA0372DP1G →
onsemi
Package: 16-lead SOIC
Crossover Distortion: No deadband crossover distortion
Mounting Type: Surface mount
İle Karşılaştır TCA0372DP1G →

TCA0372DP1

✅ Yerleştirme
onsemi
📦 8-pin PDIP
Dual power operational amplifier · 2 channels · 1.0 A · 5 V to 40 V · 1.4 MHz · No deadband crossover distortion · 8-PDIP · 8 pins

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

TCA0372BDP1

✅ Yerleştirme
onsemi
📦 8-pin PDIP
Dual power operational amplifier · 2 channels · 5 V to 40 V · 1.0 A per channel · Dual, single-ended operational-amplifier output · 8-PDIP, 8 pins · Through-hole · Servo amplifiers and power supplies

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

TCA0372DW

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
onsemi
📦 8-pin PDIP
Dual power operational amplifier · 2 circuits · 1.0 A · 5 V to 40 V · 16-lead SOIC · Surface mount · No deadband crossover distortion · Power operational amplification

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

TCA0372B

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin PDIP
B-series family member with the same dual power-amplifier architecture and PDIP format; revision-specific limits must be checked

📋 Katalogda Olmayan Referans Alternatifi

NCV0372B

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
📦 8-pin PDIP
Automotive NCV-branded B-series variant with the same power-amplifier family and PDIP format; qualification and temperature coverage are the principal distinctions

📋 Katalogda Olmayan Referans Alternatifi

TCA0372DP1G Maksimum Değerlendirmeler & Elektriksel Özellikler

Amplifier Type Dual monolithic power operational amplifier
Number of Channels 2 channels
Supply Voltage Range 5 V to 40 V
Maksimum Çıkış Akımı 1.0 A
Unity-Gain Bandwidth 1.4 MHz
Input Offset Voltage 20 mV maximum
Common-Mode Rejection Ratio 90 dB nominal
Crossover Distortion No dead-band crossover distortion
Package Type 8-pin PDIP
Montaj Stili Through-hole
Temperature Grade Extended temperature
Total Supply Voltage 40 V maximum
Output Current per Channel 1.0 A maximum

TCA0372DP1G 8-pin pdip Pin Yapısı Kılavuzu

TCA0372DP1G (8-pin pdip paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.

8-pin pdip paket pin çizelgesi için TCA0372DP1G

Ayrıntılı pin çıkış verisi mevcut değil: TCA0372DP1G.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

TCA0372DP1G için uygundur 6 uygulamas: Servo-Motor Position Control, Inductive Actuator Drive, Audio Power Output Stage, Power-Supply Error Amplifier, Dual-Axis Industrial Motion Control, Programmable DC Power Regulation.

🏭

Servo-Motor Position Control

The TCA0372DP1G fits servo-position loops where a precision error signal must drive a motor winding with substantially more current than a conventional op amp can provide. Its 1.0 A output rating and 1.4 MHz unity-gain bandwidth allow the amplifier to combine current amplification with useful closed-loop bandwidth, while the 90 dB nominal common-mode rejection helps reject disturbance common to both feedback inputs. Place the power stage in the forward path and add a suitable flyback clamp across the motor winding. The 20 mV maximum input offset voltage should be included in the position-error budget, especially for high-precision positioning systems.

⚡

Inductive Actuator Drive

The TCA0372DP1G is well matched to solenoids, voice-coil actuators, and electromagnetic valves that require controlled bidirectional current from a low-level command signal. Its 1.0 A output capability and no-dead-band crossover characteristic improve low-current drive behavior compared with an output stage containing a pronounced transition dead zone. The 5 V to 40 V supply range supports industrial control systems, while dual channels can drive two actuators or form a differential output arrangement. External current sensing and flyback protection remain essential, and PWM-driven coils should be checked for output-stage heating and stability.

🎧

Audio Power Output Stage

The TCA0372DP1G can serve as a power output stage in audio systems requiring a discrete operational amplifier rather than a conventional low-current signal amplifier. Its 1.0 A current capability supports loudspeaker drive, and the absence of dead-band crossover distortion can improve behavior around the output transition region. The 1.4 MHz unity-gain bandwidth provides adequate loop bandwidth for many audio control and feedback arrangements. System-level design must address channel-to-channel gain matching, DC offset, speaker protection, and stable feedback compensation. Thermal performance is especially important because sustained high-current audio output can raise the PDIP device temperature rapidly.

🔧

Power-Supply Error Amplifier

The TCA0372DP1G can amplify the error signal in a high-current regulated power supply, where the power stage requires both high voltage capability and 1.0 A output drive. Its 5 V to 40 V operating range fits industrial supply architectures, and the no-dead-band crossover characteristic supports accurate current regulation near zero crossing. The two channels may be used for separate positive and negative loops or for dual-output regulation. Careful loop compensation is necessary because the power amplifier adds substantial gain and phase behavior around its 1.4 MHz unity-gain bandwidth. Output saturation recovery and load-transient response should also be evaluated.

🏭

Dual-Axis Industrial Motion Control

The two channels in the TCA0372DP1G suit dual-axis motion systems in which two independent servo amplifiers must share a PCB footprint. Each channel provides the same 1.0 A output class and 1.4 MHz unity-gain bandwidth, allowing a factory automation controller to apply position or velocity feedback to two orthogonal axes. The through-hole 8-pin PDIP package is easy to inspect and service in industrial equipment. Maintain separate feedback and compensation networks unless a true differential configuration is intended. Axis matching, common grounding, inductive-clamp design, and channel thermal interaction require evaluation before production release.

🖥️

Programmable DC Power Regulation

The TCA0372DP1G can drive the pass element in a programmable laboratory or industrial DC source when the feedback network requires higher current than a standard operational amplifier can supply. Its 1.0 A output rating allows the error amplifier to control a power transistor stage over a useful operating range, and the 5 V to 40 V supply range supports numerous laboratory rail architectures. The 90 dB nominal common-mode rejection ratio helps isolate sensing nodes from common-mode voltage. Compensation must be tuned around the complete power-stage bandwidth, while the offset specification and output saturation behavior determine achievable regulation accuracy.

Önerilen Ürünler Özeti

TCA0372DP1 onsemi Kullanıldığı Yer: Servo-Motor Position Control, Inductive Actuator Drive, Audio Power Output Stage, Power-Supply Error Amplifier, Dual-Axis Industrial Motion Control, Programmable DC Power Regulation TCA0372BDP1 onsemi Kullanıldığı Yer: Servo-Motor Position Control, Power-Supply Error Amplifier TCA0372B Same-family PDIP power-amplifier candidate Kullanıldığı Yer: Inductive Actuator Drive, Dual-Axis Industrial Motion Control TCA0372D Same-family PDIP amplifier option Kullanıldığı Yer: Audio Power Output Stage NCV0372B Same-family power-amplifier candidate Kullanıldığı Yer: Programmable DC Power Regulation
What is the onsemi TCA0372DP1G?
The onsemi TCA0372DP1G is a dual monolithic power operational amplifier with a 1.0 A output-current rating, a 5 V to 40 V supply range, and a 1.4 MHz unity-gain bandwidth in an 8-pin PDIP package. According to the onsemi TCA0372 datasheet, it is intended for applications including servo amplifiers and power supplies. Its no-dead-band crossover behavior is particularly useful when driving coils and other inductive loads.
What are the key specifications of TCA0372DP1G that engineers should know?
The TCA0372DP1G combines two power-amplifier channels, a 1.0 A output-current rating, a 5 V to 40 V supply range, and a 1.4 MHz unity-gain bandwidth in an 8-pin PDIP package. The onsemi datasheet also identifies no-dead-band crossover distortion as a key feature. A nominal 90 dB common-mode rejection ratio and maximum 20 mV input offset voltage further define its signal-conditioning performance.
What is the supply voltage range of TCA0372DP1G?
The TCA0372DP1G operates from 5 V to 40 V, as identified in the onsemi product-page listing and the manufacturer datasheet. Its total operating range supports higher-voltage industrial systems while retaining a lower-voltage operating point for smaller control systems. The actual usable rail combination must remain within the absolute maximum and common-mode limits specified in the manufacturer datasheet.
How much current can TCA0372DP1G output?
The TCA0372DP1G is rated for output current to 1.0 A. The onsemi TCA0372 datasheet identifies the device as a monolithic power operational amplifier intended to drive coils and power-supply outputs. Sustained operation near this limit requires careful review of supply voltage, output voltage, duty cycle, package dissipation, PCB copper, and ambient temperature.
Is TCA0372DP1G suitable for driving servo motors and coils?
Yes, the TCA0372DP1G is specifically suited to servo amplifiers and other coil-driving systems. Its 1.0 A output-current capability and no-dead-band crossover characteristic support responsive current or voltage drive into inductive loads. The amplifier still requires suitable external flyback protection, and the load must remain within the device's voltage, current, thermal, and stability limits.
Where can I download the TCA0372DP1G datasheet PDF?
The official onsemi TCA0372 datasheet PDF is available at https://www.onsemi.com/pdf/datasheet/tca0372-d.pdf. It covers the TCA0372 family, including the TCA0372, TCA0372B, and NCV0372B devices, and provides the authoritative electrical characteristics, pin information, application circuits, and handling guidance needed for an LCA0372DP1G design.
Where can I find the TCA0372DP1G pinout?
The TCA0372DP1G pinout is defined in the pin-configuration section of the onsemi TCA0372 datasheet at https://www.onsemi.com/pdf/datasheet/tca0372-d.pdf. Use that diagram when assigning the eight PDIP connections, including power, bias bypass, input, output, and compensation-related nodes. Board-layout work should follow the manufacturer’s application circuit rather than inferring connections from another amplifier package.
TCA0372DP1G vs TCA0372DP1: which should I choose?
TCA0372DP1G and TCA0372DP1 both identify onsemi's 8-pin PDIP power-amplifier family, but the suffix G denotes the tube packaging offered for this listing. The target TCA0372DP1G is listed as the extended-temperature version, while TCA0372DP1 is presented as the standard 5 V to 40 V, 1 A device. Confirm the temperature grade, packing method, and manufacturer ordering requirements before treating one as the replacement.
What is the best drop-in replacement for TCA0372DP1G?
The closest documented same-brand replacement candidate is TCA0372DP1 because it uses the same 8-pin PDIP power-amplifier format and shares the 5 V to 40 V, 1 A output-current class. TCA0372BDP1 is another onsemi PDIP candidate to review for electrical and lifecycle differences. Because the target is obsolete, verify temperature grade, offset voltage, compensation, and production status directly before approving a substitution.
Can TCA0372DP1 replace TCA0372DP1G on an existing PCB?
TCA0372DP1 may be pin-compatible with the TCA0372DP1G footprint because both are listed as onsemi 8-pin PDIP power amplifiers, but a replacement requires confirmation of temperature grade and every electrical limit. The target is listed as extended temperature, whereas TCA0372DP1 is identified as the standard version. Review the manufacturer datasheet and qualification records before using it in temperature-critical equipment.
What can replace TCA0372DP1G in a dual power-amplifier circuit?
TCA0372DP1, TCA0372BDP1, and other onsemi PDIP members of the TCA0372 family are the primary candidates to evaluate because they are documented around the same dual power-amplifier family and 8-pin PDIP format. No verified cross-brand, pin-to-pin replacement was identified in the reviewed cross-reference listings. Validate pin functions, bias-bypass requirements, compensation, temperature grade, and electrical limits before replacement.
Is TCA0372DP1G the same as LM1877?
The TCA0372DP1G is an onsemi dual power operational amplifier, while LM1877 is a Texas Instruments single power operational amplifier associated with audio applications. They are not identical devices or direct package-level replacements. A circuit conversion must address channel count, pinout, supply requirements, bias connection, compensation, thermal design, and output-stage compatibility rather than relying only on the shared power-amplifier function.
When should I choose TCA0372DP1G instead of TCA0372DP1?
Choose TCA0372DP1G when the system specifically requires the onsemi part identified as the extended-temperature 5 V to 40 V, 1 A dual power-op-amp version and can accept its tube-packed PDIP format. Consider TCA0372DP1 when its standard temperature grade is adequate and its sourcing or lifecycle status better matches the design. Both require final review against the manufacturer electrical characteristics.
Is TCA0372DP1G still in production?
The TCA0372DP1G is listed with an obsolete lifecycle status. For a new design, evaluate an actively supported power-amplifier option unless maintaining an existing installation is the only objective. For repair or continuation of an approved legacy product, request current availability and lot traceability through the Request a Quote form on this page.
Where can I buy TCA0372DP1G and what is its lead time?
The TCA0372DP1G is an obsolete onsemi dual power operational amplifier, and current stock should not be assumed from historical listings. Use the Request a Quote form on this page to request exact-MPN availability, lot status, packaging, and lead time. For production continuity, also evaluate whether an actively supported replacement is more appropriate than relying on legacy inventory.

Mühendislik referans verileri: TCA0372DP1G — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the TCA0372DP1G only when the legacy 8-pin PDIP footprint, dual power-amplifier architecture, 1.0 A output rating, and extended-temperature designation match the intended industrial servo, actuator, or power-control design. TCA0372DP1 is the closest documented same-family candidate when standard-temperature operation is acceptable, but its production status and electrical details must be confirmed. TCA0372BDP1 and the B-series family may suit a board requiring revision-specific characteristics, subject to complete datasheet review. TCA0372D and NCV0372B are useful same-family candidates only after temperature, qualification, compensation, and lifecycle requirements are reconciled. No verified cross-brand, pin-to-pin replacement was identified. For new production, favor an actively supported power amplifier unless maintaining the existing onsemi TCA0372 implementation is mandatory.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün TCA0372DP1 TCA0372BDP1 TCA0372D TCA0372B NCV0372B
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand onsemi onsemi onsemi onsemi onsemi onsemi
Function Dual power operational amplifier Dual power operational amplifier Dual power operational amplifier Dual power operational amplifier Dual power operational amplifier Dual power operational amplifier

Ana Farklılayıcılar

  • Extended-temperature designation distinguishes the target from the standard TCA0372DP1 listing (karşılaştırma:TCA0372DP1)
  • Dual-channel architecture integrates two power operational amplifiers in one 8-pin PDIP (karşılaştırma:TCA0372BDP1)
  • Power-stage output capability supports direct coil and actuator drive (karşılaştırma:TCA0372D)

Tasarım Notları

Estimated: power dissipation equals output voltage times output current for a class-AB output stage, plus internal losses. At 20 V output and 0.5 A, the load accounts for approximately 10 W; at 40 V output and 1.0 A, it accounts for approximately 40 W. These conditions exceed practical continuous operation in an 8-pin PDIP without substantial thermal design. Use the manufacturer dissipation and thermal-resistance data to select operating limits, duty cycle, copper area, and ambient-temperature derating.

Place the required bias-bypass capacitor directly between the bias node and ground, and keep this connection short to reduce supply-generated noise and startup transients. The onsemi datasheet application guidance referenced in the LM1877 replacement discussion identifies 50 uF as the bias bypass value. Verify the final value against the manufacturer circuit because capacitor tolerance, ESR, and the amplifier's operating frequency can alter startup and stability behavior.

Do not treat the 1.0 A output-current rating as an unrestricted continuous-load specification. Output current, output voltage, supply voltage, duty cycle, junction temperature, and package dissipation are interdependent. Inductive loads also require an external flyback path to prevent excessive output voltage during current interruption. Before using the obsolete TCA0372DP1G in new equipment, review the complete onsemi electrical characteristics and absolute-maximum table.

Use a low-impedance ground reference for feedback, bias bypass, and output-current return paths. Keep high-current load current away from the feedback node so voltage drops in copper do not appear as amplifier error. For a through-hole PDIP design, use adequately plated through holes and consider thermal copper on the board despite the absence of a dedicated exposed pad. Follow the manufacturer application schematic when assigning compensation and decoupling connections.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The target is an obsolete onsemi component. Compliance attributes require confirmation from the manufacturer or authoritative product documentation before use in regulated applications.

İlgili Aramalar

TCA0372DP1G datasheet TCA0372DP1G pinout TCA0372DP1G datasheet pdf TCA0372DP1G equivalent TCA0372DP1G replacement TCA0372DP1G cross reference TCA0372DP1G vs TCA0372DP1 TCA0372DP1G price TCA0372DP1G stock onsemi TCA0372DP1G TCA0372DP1G 8-PDIP TCA0372DP1G servo amplifier TCA0372DP1G 1A output TCA0372DP1G 40V power op amp TCA0372DP1G obsolete replacement

İlgili Bileşenler ve Terimler

onsemi TCA0372DP1G TCA0372DP1 TCA0372BDP1 TCA0372D TCA0372B NCV0372B power operational amplifier operational amplifier amplifier IC signal amplifier semiconductor dual amplifier servo amplifier power-supply error amplifier coil driver 1.0 A output current 5 V to 40 V supply voltage 1.4 MHz unity-gain bandwidth 90 dB common-mode rejection ratio 20 mV input offset voltage 8-pin PDIP PDIP package family through-hole mounting
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle