TCA0372DP1G - 1A Dual Power Op Amp | onsemi
MPN: TCA0372DP1G ✗ 停產TCA0372DP1G 概覽
A power operational amplifier is a voltage-controlled amplifier that combines the high input impedance and closed-loop control of an ordinary operational amplifier with substantially greater output-current capability. Within the power-management and signal-chain hierarchy, the TCA0372 belongs to the amplifier IC family and is commonly used where a low-level error or control signal must directly drive a coil, motor winding, speaker, or power-supply output stage.
The TCA0372's 1.0 A output-current capability makes it suitable for servo amplifiers, regulated power supplies, and industrial actuator drivers. Its no-dead-band crossover-distortion characteristic improves drive into inductive coils compared with solutions exhibiting an output transition dead zone. The two independent channels also permit mirrored, complementary, or dual-axis motion-control architectures while preserving identical amplifier characteristics.
The monolithic dual-amplifier design simplifies system implementation by placing two power op-amp channels in one package. The 1.4 MHz unity-gain bandwidth supports applications that require both low-frequency loop control and useful bandwidth for dynamic feedback systems. The 90 dB nominal common-mode rejection ratio helps isolate the input stage from common-mode disturbances, while the 20 mV maximum input offset voltage defines the practical DC error boundary that must be considered in precision servo loops.
Typical uses include servo-motor control, audio output stages, power-supply regulation, industrial positioning systems, and actuator drivers. Two amplifiers in one PDIP package can reduce board area when a system requires dual-axis control or complementary drive. Where the load is inductive, flyback current must be controlled with an external clamp path, and where the load is capacitive, stability must be checked using the feedback network and load conditions.
The primary design tradeoff is sustained output-current capability versus heat generated inside the 8-pin PDIP package. A 1.0 A rating does not imply that every load condition can be driven continuously without thermal analysis. Verify copper area, ambient temperature, output duty cycle, voltage headroom, and required safety margin before using the full current rating. Follow the onsemi datasheet for recommended compensation, bias-pin bypass, and application-circuit details.
This page organizes the key electrical limits, application guidance, drop-in candidates, and package-level design considerations for engineers evaluating the TCA0372DP1G in dual power-amplifier systems.
直接替換替代品,適用於 TCA0372DP1G — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TCA0372DP1G (相同外形與佔位) — 差異在於 Package, Maximum Output Current, Crossover Distortion, Mounting Type, Amplifier Type.
TCA0372DP1
✅ 直接替換聯絡詢價
查看資料表 →TCA0372BDP1
✅ 直接替換聯絡詢價
查看資料表 →TCA0372DW
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →TCA0372B
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
NCV0372B
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TCA0372DP1G 最大額定值與電氣特性
| Amplifier Type | Dual monolithic power operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 5 V to 40 V |
| 最大輸出電流 | 1.0 A |
| Unity-Gain Bandwidth | 1.4 MHz |
| Input Offset Voltage | 20 mV maximum |
| Common-Mode Rejection Ratio | 90 dB nominal |
| Crossover Distortion | No dead-band crossover distortion |
| Package Type | 8-pin PDIP |
| 安裝方式 | Through-hole |
| Temperature Grade | Extended temperature |
| Total Supply Voltage | 40 V maximum |
| Output Current per Channel | 1.0 A maximum |
TCA0372DP1G 8-pin pdip 腳位配置指南
TCA0372DP1G(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TCA0372DP1G.
請參閱 資料表 以查看完整腳位配置。
典型應用
TCA0372DP1G 適用於 6 應用s: Servo-Motor Position Control, Inductive Actuator Drive, Audio Power Output Stage, Power-Supply Error Amplifier, Dual-Axis Industrial Motion Control, Programmable DC Power Regulation.
Servo-Motor Position Control
The TCA0372DP1G fits servo-position loops where a precision error signal must drive a motor winding with substantially more current than a conventional op amp can provide. Its 1.0 A output rating and 1.4 MHz unity-gain bandwidth allow the amplifier to combine current amplification with useful closed-loop bandwidth, while the 90 dB nominal common-mode rejection helps reject disturbance common to both feedback inputs. Place the power stage in the forward path and add a suitable flyback clamp across the motor winding. The 20 mV maximum input offset voltage should be included in the position-error budget, especially for high-precision positioning systems.
推薦
Inductive Actuator Drive
The TCA0372DP1G is well matched to solenoids, voice-coil actuators, and electromagnetic valves that require controlled bidirectional current from a low-level command signal. Its 1.0 A output capability and no-dead-band crossover characteristic improve low-current drive behavior compared with an output stage containing a pronounced transition dead zone. The 5 V to 40 V supply range supports industrial control systems, while dual channels can drive two actuators or form a differential output arrangement. External current sensing and flyback protection remain essential, and PWM-driven coils should be checked for output-stage heating and stability.
推薦
Audio Power Output Stage
The TCA0372DP1G can serve as a power output stage in audio systems requiring a discrete operational amplifier rather than a conventional low-current signal amplifier. Its 1.0 A current capability supports loudspeaker drive, and the absence of dead-band crossover distortion can improve behavior around the output transition region. The 1.4 MHz unity-gain bandwidth provides adequate loop bandwidth for many audio control and feedback arrangements. System-level design must address channel-to-channel gain matching, DC offset, speaker protection, and stable feedback compensation. Thermal performance is especially important because sustained high-current audio output can raise the PDIP device temperature rapidly.
推薦
Power-Supply Error Amplifier
The TCA0372DP1G can amplify the error signal in a high-current regulated power supply, where the power stage requires both high voltage capability and 1.0 A output drive. Its 5 V to 40 V operating range fits industrial supply architectures, and the no-dead-band crossover characteristic supports accurate current regulation near zero crossing. The two channels may be used for separate positive and negative loops or for dual-output regulation. Careful loop compensation is necessary because the power amplifier adds substantial gain and phase behavior around its 1.4 MHz unity-gain bandwidth. Output saturation recovery and load-transient response should also be evaluated.
推薦
Dual-Axis Industrial Motion Control
The two channels in the TCA0372DP1G suit dual-axis motion systems in which two independent servo amplifiers must share a PCB footprint. Each channel provides the same 1.0 A output class and 1.4 MHz unity-gain bandwidth, allowing a factory automation controller to apply position or velocity feedback to two orthogonal axes. The through-hole 8-pin PDIP package is easy to inspect and service in industrial equipment. Maintain separate feedback and compensation networks unless a true differential configuration is intended. Axis matching, common grounding, inductive-clamp design, and channel thermal interaction require evaluation before production release.
推薦
Programmable DC Power Regulation
The TCA0372DP1G can drive the pass element in a programmable laboratory or industrial DC source when the feedback network requires higher current than a standard operational amplifier can supply. Its 1.0 A output rating allows the error amplifier to control a power transistor stage over a useful operating range, and the 5 V to 40 V supply range supports numerous laboratory rail architectures. The 90 dB nominal common-mode rejection ratio helps isolate sensing nodes from common-mode voltage. Compensation must be tuned around the complete power-stage bandwidth, while the offset specification and output saturation behavior determine achievable regulation accuracy.
推薦
推薦產品摘要
工程參考資料,適用於 TCA0372DP1G — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TCA0372DP1 | TCA0372BDP1 | TCA0372D | TCA0372B | NCV0372B |
|---|---|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi | onsemi |
| Function | Dual power operational amplifier | Dual power operational amplifier | Dual power operational amplifier | Dual power operational amplifier | Dual power operational amplifier | Dual power operational amplifier |
主要差異化特點
- Extended-temperature designation distinguishes the target from the standard TCA0372DP1 listing (對比TCA0372DP1)
- Dual-channel architecture integrates two power operational amplifiers in one 8-pin PDIP (對比TCA0372BDP1)
- Power-stage output capability supports direct coil and actuator drive (對比TCA0372D)
設計說明
Estimated: power dissipation equals output voltage times output current for a class-AB output stage, plus internal losses. At 20 V output and 0.5 A, the load accounts for approximately 10 W; at 40 V output and 1.0 A, it accounts for approximately 40 W. These conditions exceed practical continuous operation in an 8-pin PDIP without substantial thermal design. Use the manufacturer dissipation and thermal-resistance data to select operating limits, duty cycle, copper area, and ambient-temperature derating.
Place the required bias-bypass capacitor directly between the bias node and ground, and keep this connection short to reduce supply-generated noise and startup transients. The onsemi datasheet application guidance referenced in the LM1877 replacement discussion identifies 50 uF as the bias bypass value. Verify the final value against the manufacturer circuit because capacitor tolerance, ESR, and the amplifier's operating frequency can alter startup and stability behavior.
Do not treat the 1.0 A output-current rating as an unrestricted continuous-load specification. Output current, output voltage, supply voltage, duty cycle, junction temperature, and package dissipation are interdependent. Inductive loads also require an external flyback path to prevent excessive output voltage during current interruption. Before using the obsolete TCA0372DP1G in new equipment, review the complete onsemi electrical characteristics and absolute-maximum table.
Use a low-impedance ground reference for feedback, bias bypass, and output-current return paths. Keep high-current load current away from the feedback node so voltage drops in copper do not appear as amplifier error. For a through-hole PDIP design, use adequately plated through holes and consider thermal copper on the board despite the absence of a dedicated exposed pad. Follow the manufacturer application schematic when assigning compensation and decoupling connections.
合規資訊
The target is an obsolete onsemi component. Compliance attributes require confirmation from the manufacturer or authoritative product documentation before use in regulated applications.