LAST TIME BUY NOTICE: TJA1054AT son sipariş tarihi yaklaşmakta. Son sipariş tarihi: Bize Ulaşın. Kullanılabilir alternatif parçaları görüntüle →
NXP Semiconductors

TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP

MPN: TJA1054AT ✗ Son Kullanım Zamanı
SO14, 14 pins Package
MOQ: 1 |

TJA1054AT Genel Bakış

NXP Semiconductors TJA1054AT is a fault-tolerant Controller Area Network transceiver intended for low-speed, single-wire CAN communication up to 125 kBd, supplied in a 14-pin SOIC package. The device sits between a CAN protocol controller and the physical bus wiring, providing the interface required to transmit and receive CAN signals while adding protection against faults on the bus.

A CAN transceiver is the physical-layer component between a digital CAN controller and its bus wiring. The controller processes frames and protocol functions, while the transceiver converts logical controller signals into electrical bus signals and presents received bus information to the controller. A single-wire CAN interface uses one signal line for communication and normally requires a return path through the vehicle or equipment ground structure. The TJA1054AT is therefore positioned within the hierarchy of CAN interface IC, network interface, communications semiconductor, and integrated circuit.

The TJA1054AT provides operation up to 125 kBd and is identified as a fault-tolerant CAN transceiver. The TJA1054A family is an electrostatic-discharge-improved version of the original TJA1054. NXP states that the TJA1054AT is pin and downward compatible with the PCA82C252T and TJA1053T, allowing those devices to be replaced while retaining their functions. Its SO14 package is a surface-mount package suitable for conventional automotive and industrial controller-board layouts.

The principal design benefit is fault tolerance in environments where a CAN conductor may be exposed to wiring faults. Its 125 kBd maximum intended data rate supports low-speed CAN networks in passenger-car systems and other cost-sensitive embedded networks. A design must still observe the transceiver's detailed operating limits, bus topology, termination strategy, supply requirements, and external protection requirements defined by the manufacturer datasheet.

Typical uses include body and comfort-control modules, passenger-car diagnostic equipment, low-speed automotive gateways, industrial control panels, and embedded CAN controllers. The device is most appropriate where a single-wire bus and fault-resilient physical interface are required. It should not be confused with differential two-wire CAN transceivers, which use separate CANH and CANL conductors.

For PCB implementation, use the exact pin numbering and pin descriptions in the NXP data sheet, place the transceiver close to the connector or bus routing, and keep the CAN trace away from high-current switching paths. Confirm bus polarity, ground reference, decoupling, and any required external components during schematic review.

This page adds lifecycle context, documented replacement relationships, package-level comparison, and practical design guidance around the TJA1054AT. Because NXP identifies the part as end of life, engineers should validate supply continuity, approved lifecycle status, and a complete sourcing plan before committing a new production design to this device.

Drop-in alternatifler için TJA1054AT — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller TJA1054AT (aynı form faktörü ve ayağa oturma) — farklı olan Fault Tolerance, Package.

NXP Semiconductors
Fault Tolerance: Enhanced fault-tolerant bus-line interface
Package: SOIC-14 / SOP-14 surface-mount package
İle Karşılaştır TJA1054AT →

TJA1054T

✅ Yerleştirme
📦 SO14
The TJA1054T is the related non-A suffix member; its ordering details differ while NXP describes the TJA1054AT as compatible with the PCA82C252T and TJA1053T.

📋 Katalogda Olmayan Referans Alternatifi

PCA82C252T

✅ Yerleştirme
📦 SO14
The PCA82C252T is an earlier single-wire CAN interface; NXP states that the TJA1054AT retains its functions and adds the TJA1054A ESD improvement.

📋 Katalogda Olmayan Referans Alternatifi

TJA1053T

✅ Yerleştirme
📦 SO14
The TJA1053T is an earlier single-wire CAN transceiver; NXP documents replacement by the TJA1054AT with retention of all stated functions.

📋 Katalogda Olmayan Referans Alternatifi

TJA1054AT Özellikler

Product Type Fault-tolerant single-wire CAN transceiver
Manufacturer NXP Semiconductors
Maximum Intended Data Rate 125 kBd
CAN Bus Type Single-wire CAN
Interface Function Protocol controller to physical bus-wire interface
ESD Improvement ElectroStatic Discharge improved version of TJA1054
Fault Tolerance Fault-tolerant CAN operation
Paket SO14, 14 pins
Montaj Türü Surface mount
Primary Application Low-speed passenger-car CAN networks
Documented Compatible Part PCA82C252T
Documented Compatible Part TJA1053T

TJA1054AT so14, 14 pins Pin Yapısı Kılavuzu

TJA1054AT (so14, 14 pins paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

so14, 14 pins paket pin çizelgesi için TJA1054AT

Ayrıntılı pin çıkış verisi mevcut değil: TJA1054AT.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

TJA1054AT için uygundur 6 uygulamas: Passenger-Car Body Control, Low-Speed Automotive Diagnostics, Industrial CAN Control Panels, Embedded Equipment Gateways, Distributed Sensor and Actuator Networks, Legacy CAN Module Maintenance.

🚗

Passenger-Car Body Control

The TJA1054AT fits low-speed passenger-car body and comfort-control networks because it provides a fault-tolerant single-wire CAN interface for data rates up to 125 kBd. Positioned between the CAN controller and the physical bus, it lets distributed modules exchange switch, sensor, and status information over one CAN signal conductor. The 14-pin SOIC package supports conventional surface-mount PCB construction. Its documented compatibility with the PCA82C252T and TJA1053T also makes it useful when maintaining an established automotive module platform, provided that lifecycle and sourcing review is completed before release.

🚗

Low-Speed Automotive Diagnostics

The TJA1054AT is suitable for low-speed diagnostic and service interfaces that operate at or below 125 kBd over a single-wire CAN bus. Its fault-tolerant architecture is appropriate for vehicle wiring systems where transient disturbances and connection faults may occur. The device interfaces a CAN controller with the external bus wiring rather than implementing the protocol itself, allowing the host controller to handle frames, diagnostics, and message arbitration. Engineers should use the NXP pin descriptions when connecting the 14-pin SOIC device and validate grounding, protection, and bus topology for the target vehicle platform.

🏭

Industrial CAN Control Panels

The TJA1054AT can support a low-speed industrial control panel that uses single-wire CAN for connecting a controller to remote modules. Its 125 kBd intended data rate is appropriate for supervisory status, configuration, and slow actuator traffic rather than motion-control data streams. The fault-tolerant interface adds resilience in distributed equipment where a single bus conductor simplifies cabling. The SO14 package is easy to incorporate into conventional controller-board layouts, but the designer must follow the manufacturer data sheet for supply decoupling, connector protection, bus reference ground, and timing constraints.

🔧

Embedded Equipment Gateways

The TJA1054AT is applicable to embedded gateways that bridge a single-wire CAN network to another controller or host processor. By handling the physical interface between the CAN controller and bus wiring, it allows the host to devote its resources to protocol processing and application data. The intended 125 kBd rate suits supervisory and control traffic, while fault tolerance can improve behavior in long harnesses or distributed industrial installations. Because the device is packaged in 14-pin SOIC, implementation is straightforward on existing single-wire CAN boards, subject to detailed electrical validation and an end-of-life supply review.

🧩

Distributed Sensor and Actuator Networks

The TJA1054AT can interface a CAN controller with distributed sensors and actuators connected through a single-wire CAN network. Its fault-tolerant design is useful where field wiring may be long or exposed to electrical transients, while the 125 kBd target rate is suitable for periodic measurements and supervisory commands rather than high-frequency sensor streaming. The 14-pin SOIC package permits compact integration into remote I/O modules. Designers should verify the complete bus network, grounding arrangement, connector pin definition, and protection scheme against the NXP data sheet before deployment.

🔧

Legacy CAN Module Maintenance

The TJA1054AT is particularly relevant to maintenance programs for electronics built around the PCA82C252T or TJA1053T. NXP states that the TJA1054AT can replace those devices while retaining their functions, reducing the mechanical and functional impact of a component migration. Its TJA1054A family also provides the documented electrostatic-discharge improvement associated with the revised device. This makes it a practical option for controlled redesigns of legacy single-wire CAN modules, although engineers must compare worst-case electrical limits and obtain a complete lifecycle and supply assessment before production use.

Önerilen Ürünler Özeti

TJA1054T Closely related NXP single-wire CAN transceiver Kullanıldığı Yer: Passenger-Car Body Control, Low-Speed Automotive Diagnostics, Industrial CAN Control Panels, Embedded Equipment Gateways, Distributed Sensor and Actuator Networks, Legacy CAN Module Maintenance PCA82C252T Documented pin-compatible predecessor Kullanıldığı Yer: Passenger-Car Body Control, Industrial CAN Control Panels, Distributed Sensor and Actuator Networks, Legacy CAN Module Maintenance TJA1053T Documented functionally compatible predecessor Kullanıldığı Yer: Passenger-Car Body Control, Low-Speed Automotive Diagnostics, Embedded Equipment Gateways, Legacy CAN Module Maintenance
What is the TJA1054AT datasheet?
The TJA1054AT datasheet is the NXP document describing a fault-tolerant, single-wire CAN transceiver intended for operation up to 125 kBd. It covers the device functions, electrical characteristics, pin descriptions, application information, and compatibility information. Download the document from the NXP TJA1054A data-sheet link on this page, and use the TJA1054AT-specific ordering information to confirm the selected suffix.
Where can I find the TJA1054AT pinout?
The TJA1054AT pinout is shown in the pin-description and package-drawing sections of the NXP TJA1054A data sheet. The device uses a 14-pin SOIC package. Assign PCB nets from that table rather than relying on a generic SO14 drawing, because the CAN bus, transmit, receive, supply, ground, and control connections are application-specific.
What type of CAN interface does the TJA1054AT provide?
The TJA1054AT provides a single-wire CAN physical-layer interface between a protocol controller and the CAN bus wiring. It is intended for low-speed networks operating up to 125 kBd. Unlike a differential CAN transceiver, it does not use separate CANH and CANL conductors, so it must not be substituted into a conventional two-wire CAN circuit without a complete electrical review.
What is the maximum data rate of the TJA1054AT?
The TJA1054AT is intended for CAN communication rates up to 125 kBd. This figure identifies its primary low-speed passenger-car application rather than the higher rates supported by high-speed differential CAN transceivers. Keep the selected controller, bus length, termination arrangement, oscillator accuracy, and transceiver timing within the limits specified by the manufacturer data sheet.
What can replace the TJA1054AT?
NXP identifies the TJA1054AT as pin and downward compatible with the PCA82C252T and TJA1053T while retaining their functions. These are documented replacement relationships, but downward compatibility should be checked against every electrical, timing, fault-mode, and lifecycle requirement in the original design. The TJA1054T is another closely related NXP member, though the data sheet should be reviewed before using it as a substitute.
Is the TJA1054AT the same as the TJA1054T?
The TJA1054AT and TJA1054T are closely related NXP devices, and NXP discusses both in the TJA1054A product material. However, suffix, temperature, package, ordering, and qualification details can distinguish the orderable versions. Compare the complete ordering tables and pin descriptions before treating one as a drop-in replacement for the other.
When should I choose the TJA1054AT over the TJA1053T?
Choose the TJA1054AT over the TJA1053T when the design needs the newer TJA1054A fault-tolerant single-wire CAN implementation and its documented functional compatibility with the TJA1053T. Because NXP states that the devices can be replaced with retention of functions, the choice should also reflect supply status, exact package suffix, environmental requirements, and whether an obsolete or end-of-life part remains appropriate for the production plan.
TJA1054AT vs PCA82C252T: which is better for an existing design?
The TJA1054AT is the better modernization candidate for an existing PCA82C252T design because NXP explicitly identifies it as pin and downward compatible while retaining the functions of the PCA82C252T. The TJA1054A also adds electrostatic-discharge improvement over the original TJA1054 family. Validate supply timing, lifecycle constraints, and all worst-case electrical conditions before production release.
Is the TJA1054AT suitable for automotive applications?
The TJA1054AT is primarily intended for low-speed passenger-car applications, but suitability depends on the exact ordering variant, operating-temperature grade, AEC-Q100 status, and production requirements. The TJA1054AT is identified as end of life, so automotive programs should also assess change-control rules, long-term availability, and any approved sourcing conditions before using it in a new vehicle design.
What is the lifecycle status of the TJA1054AT?
NXP lists the TJA1054AT as End of Life on its product page. This means engineers must not treat it as a standard active-production choice without confirming availability and approved supply conditions. For a new design, evaluate a currently supported single-wire CAN transceiver; for an existing design, create a controlled migration plan and verify mechanical, electrical, and functional compatibility.
Where can I buy the TJA1054AT online?
The TJA1054AT can be requested through the Request a Quote form on this page. Because the manufacturer lists the part as end of life, buyers should ask for exact suffix, package, temperature grade, remaining quantity, traceability, and delivery information. The quotation process is the appropriate route for reviewing availability without relying on an unqualified listing for a different orderable code.
What is the price of the TJA1054AT?
The current commercial price depends on the exact suffix, package, quantity, condition, and supply status of the TJA1054AT. Submit the required MPN and order quantity through the Request a Quote form on this page for a current quotation. Because the manufacturer lists the device as end of life, confirm condition, traceability, and the number of pieces available when requesting a quote.
What is the lead time for the TJA1054AT?
Lead time for the TJA1054AT depends on remaining factory or channel inventory, the exact orderable suffix, and the requested quantity. Use the Request a Quote form on this page to request current lead-time and minimum-order information. Because the device is marked end of life, treat any stated delivery schedule as subject to final allocation and supply confirmation.
Is the TJA1054AT in stock?
Current stock for TJA1054AT must be confirmed against the exact suffix, package, temperature grade, and required quantity. Submit these details through the Request a Quote form on this page for an availability confirmation. The manufacturer identifies the product as end of life, so buyers should request lot, date-code, traceability, and packaging information as part of the supply review.
What are the key specifications of TJA1054AT that engineers should know?
The key TJA1054AT specifications are its fault-tolerant single-wire CAN function, intended operation up to 125 kBd, 14-pin SOIC package, and status as an end-of-life NXP device. NXP also identifies it as an electrostatic-discharge-improved TJA1054A-family version and pin compatible with the PCA82C252T and TJA1053T. Supply voltage, temperature limits, and detailed timing must be taken from the manufacturer data sheet.

Mühendislik referans verileri: TJA1054AT — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the TJA1054AT when maintaining or redesigning a single-wire CAN circuit that requires the documented TJA1054A fault-tolerant implementation and operation up to 125 kBd. It is a documented functional replacement for the PCA82C252T and TJA1053T, which can simplify qualification of those legacy platforms. Consider the TJA1054T for closely related NXP family requirements, but compare its exact ordering suffix and electrical limits before substituting it. Do not choose this device for a conventional differential CAN bus using separate CANH and CANL conductors. Because NXP marks the TJA1054AT as end of life, a currently supported transceiver is normally preferable for a new design. For an existing product, use the TJA1054AT only after confirming lifecycle approval, supply traceability, package compatibility, temperature grade, timing limits, fault behavior, and worst-case electrical performance.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün TJA1054T PCA82C252T TJA1053T
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package SO14 SO14 - same SO14 - same SO14 - same
Device Type Fault-tolerant single-wire CAN transceiver Single-wire CAN transceiver Single-wire CAN interface Single-wire CAN transceiver

Ana Farklılayıcılar

  • ESD-improved TJA1054A family implementation (karşılaştırma:PCA82C252T)
  • Documented replacement of an established single-wire CAN interface (karşılaştırma:TJA1053T)
  • Fault-tolerant operation for low-speed CAN networks (karşılaştırma:TJA1054T)

Tasarım Notları

Assign every connection from the NXP TJA1054A pin-description table rather than from a generic SO14 footprint drawing. Place the transceiver close to the CAN connector or bus-routing region, minimize the unprotected bus trace, and route it away from motor-switching and high-voltage edges. Maintain the board ground reference required for the single-wire CAN return path and follow the manufacturer layout guidance for supply decoupling.

Do not treat the TJA1054AT as a direct substitute for a differential CANH/CANL transceiver. It implements single-wire CAN, so using it on a conventional two-wire bus can produce incorrect electrical behavior. Likewise, do not rely only on the documented pin compatibility of the PCA82C252T or TJA1053T; compare maximum bus length, timing, fault behavior, supply range, temperature grade, and package suffix before approving a replacement.

NXP identifies the TJA1054AT as end of life. Treat a new production commitment as a lifecycle exception requiring approved sourcing, traceability, quantity allocation, and a reviewed end-of-life plan. For maintenance programs, preserve the original footprint and pin functions where possible, but verify the exact ordering suffix rather than assuming that all TJA1054-family tape-and-reel codes are electrically and environmentally identical.

Keep the single-wire CAN route controlled and validate it with the intended bus topology and connector. The 125 kBd application target does not eliminate the need for correct grounding, protection, and timing. Review rise time, recessive and dominant levels, propagation delay, bus capacitance, and synchronization tolerance in the manufacturer data sheet before reducing trace length or changing connectors.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The available product and datasheet information identifies automotive passenger-car applications and an end-of-life status but does not provide definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for this exact orderable suffix.

Veri doğrulanma tarihi: 2026-11-09 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

tja1054at datasheet tja1054at ic datasheet nxp tja1054at TJA1054AT pinout TJA1054AT datasheet pdf TJA1054AT SO14 pinout TJA1054AT 125 kBd CAN TJA1054AT equivalent TJA1054AT replacement TJA1054AT vs PCA82C252T TJA1054AT vs TJA1053T TJA1054AT single-wire CAN TJA1054AT price TJA1054AT stock

İlgili Bileşenler ve Terimler

NXP Semiconductors TJA1054AT TJA1054A TJA1054T PCA82C252T TJA1053T Controller Area Network CAN transceiver single-wire CAN CAN protocol controller physical-layer interface fault-tolerant CAN 125 kBd electrostatic discharge ESD improvement SO14 SOIC package surface mount automotive electronics industrial control distributed sensor network low-speed CAN passenger-car network end-of-life component
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle