TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP
料号: TJA1054AT ✗ 停产TJA1054AT 概述
A CAN transceiver is the physical-layer component between a digital CAN controller and its bus wiring. The controller processes frames and protocol functions, while the transceiver converts logical controller signals into electrical bus signals and presents received bus information to the controller. A single-wire CAN interface uses one signal line for communication and normally requires a return path through the vehicle or equipment ground structure. The TJA1054AT is therefore positioned within the hierarchy of CAN interface IC, network interface, communications semiconductor, and integrated circuit.
The TJA1054AT provides operation up to 125 kBd and is identified as a fault-tolerant CAN transceiver. The TJA1054A family is an electrostatic-discharge-improved version of the original TJA1054. NXP states that the TJA1054AT is pin and downward compatible with the PCA82C252T and TJA1053T, allowing those devices to be replaced while retaining their functions. Its SO14 package is a surface-mount package suitable for conventional automotive and industrial controller-board layouts.
The principal design benefit is fault tolerance in environments where a CAN conductor may be exposed to wiring faults. Its 125 kBd maximum intended data rate supports low-speed CAN networks in passenger-car systems and other cost-sensitive embedded networks. A design must still observe the transceiver's detailed operating limits, bus topology, termination strategy, supply requirements, and external protection requirements defined by the manufacturer datasheet.
Typical uses include body and comfort-control modules, passenger-car diagnostic equipment, low-speed automotive gateways, industrial control panels, and embedded CAN controllers. The device is most appropriate where a single-wire bus and fault-resilient physical interface are required. It should not be confused with differential two-wire CAN transceivers, which use separate CANH and CANL conductors.
For PCB implementation, use the exact pin numbering and pin descriptions in the NXP data sheet, place the transceiver close to the connector or bus routing, and keep the CAN trace away from high-current switching paths. Confirm bus polarity, ground reference, decoupling, and any required external components during schematic review.
This page adds lifecycle context, documented replacement relationships, package-level comparison, and practical design guidance around the TJA1054AT. Because NXP identifies the part as end of life, engineers should validate supply continuity, approved lifecycle status, and a complete sourcing plan before committing a new production design to this device.
直接替换替代料: TJA1054AT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TJA1054AT (相同外形与封装尺寸) ——差异在于 Fault Tolerance, Package.
TJA1054T
✅ 直接替换📋 参考替代料(不在目录中)
PCA82C252T
✅ 直接替换📋 参考替代料(不在目录中)
TJA1053T
✅ 直接替换📋 参考替代料(不在目录中)
TJA1054AT 规格参数
| Product Type | Fault-tolerant single-wire CAN transceiver |
| Manufacturer | NXP Semiconductors |
| Maximum Intended Data Rate | 125 kBd |
| CAN Bus Type | Single-wire CAN |
| Interface Function | Protocol controller to physical bus-wire interface |
| ESD Improvement | ElectroStatic Discharge improved version of TJA1054 |
| Fault Tolerance | Fault-tolerant CAN operation |
| 封装 | SO14, 14 pins |
| 安装类型 | Surface mount |
| Primary Application | Low-speed passenger-car CAN networks |
| Documented Compatible Part | PCA82C252T |
| Documented Compatible Part | TJA1053T |
TJA1054AT so14, 14 pins 引脚配置指南
TJA1054AT(so14, 14 pins 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TJA1054AT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TJA1054AT 适用于 6 应用s: Passenger-Car Body Control, Low-Speed Automotive Diagnostics, Industrial CAN Control Panels, Embedded Equipment Gateways, Distributed Sensor and Actuator Networks, Legacy CAN Module Maintenance.
Passenger-Car Body Control
The TJA1054AT fits low-speed passenger-car body and comfort-control networks because it provides a fault-tolerant single-wire CAN interface for data rates up to 125 kBd. Positioned between the CAN controller and the physical bus, it lets distributed modules exchange switch, sensor, and status information over one CAN signal conductor. The 14-pin SOIC package supports conventional surface-mount PCB construction. Its documented compatibility with the PCA82C252T and TJA1053T also makes it useful when maintaining an established automotive module platform, provided that lifecycle and sourcing review is completed before release.
推荐
Low-Speed Automotive Diagnostics
The TJA1054AT is suitable for low-speed diagnostic and service interfaces that operate at or below 125 kBd over a single-wire CAN bus. Its fault-tolerant architecture is appropriate for vehicle wiring systems where transient disturbances and connection faults may occur. The device interfaces a CAN controller with the external bus wiring rather than implementing the protocol itself, allowing the host controller to handle frames, diagnostics, and message arbitration. Engineers should use the NXP pin descriptions when connecting the 14-pin SOIC device and validate grounding, protection, and bus topology for the target vehicle platform.
推荐
Industrial CAN Control Panels
The TJA1054AT can support a low-speed industrial control panel that uses single-wire CAN for connecting a controller to remote modules. Its 125 kBd intended data rate is appropriate for supervisory status, configuration, and slow actuator traffic rather than motion-control data streams. The fault-tolerant interface adds resilience in distributed equipment where a single bus conductor simplifies cabling. The SO14 package is easy to incorporate into conventional controller-board layouts, but the designer must follow the manufacturer data sheet for supply decoupling, connector protection, bus reference ground, and timing constraints.
推荐
Embedded Equipment Gateways
The TJA1054AT is applicable to embedded gateways that bridge a single-wire CAN network to another controller or host processor. By handling the physical interface between the CAN controller and bus wiring, it allows the host to devote its resources to protocol processing and application data. The intended 125 kBd rate suits supervisory and control traffic, while fault tolerance can improve behavior in long harnesses or distributed industrial installations. Because the device is packaged in 14-pin SOIC, implementation is straightforward on existing single-wire CAN boards, subject to detailed electrical validation and an end-of-life supply review.
推荐
Distributed Sensor and Actuator Networks
The TJA1054AT can interface a CAN controller with distributed sensors and actuators connected through a single-wire CAN network. Its fault-tolerant design is useful where field wiring may be long or exposed to electrical transients, while the 125 kBd target rate is suitable for periodic measurements and supervisory commands rather than high-frequency sensor streaming. The 14-pin SOIC package permits compact integration into remote I/O modules. Designers should verify the complete bus network, grounding arrangement, connector pin definition, and protection scheme against the NXP data sheet before deployment.
推荐
Legacy CAN Module Maintenance
The TJA1054AT is particularly relevant to maintenance programs for electronics built around the PCA82C252T or TJA1053T. NXP states that the TJA1054AT can replace those devices while retaining their functions, reducing the mechanical and functional impact of a component migration. Its TJA1054A family also provides the documented electrostatic-discharge improvement associated with the revised device. This makes it a practical option for controlled redesigns of legacy single-wire CAN modules, although engineers must compare worst-case electrical limits and obtain a complete lifecycle and supply assessment before production use.
推荐
推荐产品汇总
工程参考数据: TJA1054AT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TJA1054T | PCA82C252T | TJA1053T |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SO14 | SO14 - same | SO14 - same | SO14 - same |
| Device Type | Fault-tolerant single-wire CAN transceiver | Single-wire CAN transceiver | Single-wire CAN interface | Single-wire CAN transceiver |
关键差异点
- ESD-improved TJA1054A family implementation (对比 PCA82C252T)
- Documented replacement of an established single-wire CAN interface (对比 TJA1053T)
- Fault-tolerant operation for low-speed CAN networks (对比 TJA1054T)
设计说明
Assign every connection from the NXP TJA1054A pin-description table rather than from a generic SO14 footprint drawing. Place the transceiver close to the CAN connector or bus-routing region, minimize the unprotected bus trace, and route it away from motor-switching and high-voltage edges. Maintain the board ground reference required for the single-wire CAN return path and follow the manufacturer layout guidance for supply decoupling.
Do not treat the TJA1054AT as a direct substitute for a differential CANH/CANL transceiver. It implements single-wire CAN, so using it on a conventional two-wire bus can produce incorrect electrical behavior. Likewise, do not rely only on the documented pin compatibility of the PCA82C252T or TJA1053T; compare maximum bus length, timing, fault behavior, supply range, temperature grade, and package suffix before approving a replacement.
NXP identifies the TJA1054AT as end of life. Treat a new production commitment as a lifecycle exception requiring approved sourcing, traceability, quantity allocation, and a reviewed end-of-life plan. For maintenance programs, preserve the original footprint and pin functions where possible, but verify the exact ordering suffix rather than assuming that all TJA1054-family tape-and-reel codes are electrically and environmentally identical.
Keep the single-wire CAN route controlled and validate it with the intended bus topology and connector. The 125 kBd application target does not eliminate the need for correct grounding, protection, and timing. Review rise time, recessive and dominant levels, propagation delay, bus capacitance, and synchronization tolerance in the manufacturer data sheet before reducing trace length or changing connectors.
合规信息
The available product and datasheet information identifies automotive passenger-car applications and an end-of-life status but does not provide definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for this exact orderable suffix.