TLV2332IP - Dual 8V 525kHz Op Amp | Texas Instruments
MPN: TLV2332IP ✓ AktifTLV2332IP Genel Bakış
An operational amplifier is an analog signal-processing IC that compares voltages applied to its high-impedance differential inputs and drives an output to reflect their difference. Within the broader semiconductor hierarchy, the TLV2332IP belongs to the operational-amplifier class, then to general-purpose voltage-feedback amplifiers, and finally to linear and mixed-signal integrated circuits. Its differential input stage and high output drive make it suitable for signal conditioning, amplification, filtering, and feedback control.
The primary device characteristics include dual-channel operation, an 8 V maximum supply voltage, a 525 kHz gain-bandwidth product, and low input bias current. The low bias current reduces the error introduced when the amplifier is driven by a high-impedance source. Its 525 kHz bandwidth supports applications requiring moderate-frequency closed-loop response without operating as a high-speed precision amplifier.
The TLV233x family uses a LinCMOS low-voltage, medium-power architecture intended for single-supply operation. A single-supply configuration means the amplifier can operate with its negative input and supply pins connected to ground while processing signals referenced to a positive rail. This is useful in battery-powered and embedded systems where generating a negative supply would be impractical. Designers should still observe the complete power-supply and common-mode limits in the manufacturer datasheet.
Typical applications include sensor-signal conditioning, low-frequency active filters, audio preamplification, general-purpose buffer stages, and embedded analog signal chains. Its dual-channel layout can simplify boards requiring two modest-bandwidth amplification functions, while its PDIP package remains convenient for through-hole prototypes, educational designs, and manually assembled industrial control boards.
When using the TLV2332IP, connect the unused amplifier channel to a stable common-mode level close to the configured signal operating point. Confirm the maximum input and output voltage excursions, supply current, output-drive capability, and stability requirements against the manufacturer datasheet before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins to control impedance in the power-distribution network.
This product record combines the TLV2332 family specifications, package details, pin assignment, sourcing workflow, and practical selection guidance in one engineering reference. It supports faster design decisions while directing engineers to the manufacturer datasheet for final electrical limits, test conditions, and application-specific validation.
Drop-in alternatifler için TLV2332IP — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller TLV2332IP (aynı form faktörü ve ayağa oturma) — farklı olan Amplifier Type, Mounting Type.
TLV2332IPG4
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
TLV2332IPE4
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
TLV2332IP Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 8 V |
| Gain-Bandwidth Product | 525 kHz |
| Process Technology | LinCMOS |
| Power Class | Low-voltage medium-power |
| Supply Configuration | Single-supply capable |
| Package Type | 8-pin PDIP |
| Package Pin Count | 8 pins |
| Montaj Türü | Through-hole |
TLV2332IP Pin Yapısı
| Pin 1 | 1OUT — Output of amplifier channel 1 |
| Pin 2 | 1IN− — Inverting input of amplifier channel 1 |
| Pin 3 | 1IN+ — Non-inverting input of amplifier channel 1 |
| Pin 4 | V− — Negative supply connection |
| Pin 5 | 2IN+ — Non-inverting input of amplifier channel 2 |
| Pin 6 | 2IN− — Inverting input of amplifier channel 2 |
| Pin 7 | 2OUT — Output of amplifier channel 2 |
| Pin 8 | V+ — Positive supply connection |
Tipik Uygulamalar
TLV2332IP için uygundur 6 uygulamas: Low-Voltage Sensor Signal Conditioning, Battery-Powered Embedded Instrumentation, Active Audio Preamplifier, General-Purpose Active Filter, Industrial Control Interface, Voltage Buffer and Level Interface.
Low-Voltage Sensor Signal Conditioning
The TLV2332IP fits sensor front ends where a low-bias-current input stage preserves weak signals from resistive or high-impedance sensors. Its dual architecture can amplify one sensor channel while the second channel provides buffering, level shifting, or active filtering on the same 8 V rail. The 525 kHz gain-bandwidth product is appropriate for low-to-moderate-frequency sensor dynamics rather than wideband pulse capture. In a practical circuit, bias each input within the allowed common-mode range and place input and feedback components close to the package pins. Verify offset, bias-current, noise, and common-mode limits against the manufacturer datasheet for the selected sensor impedance.
Önerilen
Battery-Powered Embedded Instrumentation
The TLV2332IP is useful in battery-powered embedded instrumentation because it is designed for low-voltage, single-supply operation and combines two amplifiers in one 8-pin PDIP package. One channel can amplify a transducer signal while the other creates a buffered reference or performs gain conversion for an ADC input. Its 525 kHz gain-bandwidth product handles modest measurement bandwidth while keeping the design electrically simple. Confirm the operating and output common-mode limits over the full battery-discharge range, and terminate unused inputs predictably. The PDIP package also makes the device practical for prototypes assembled with through-hole components.
Önerilen
Active Audio Preamplifier
The TLV2332IP can implement a small-signal dual-channel audio preamplifier when the source impedance, gain, and bandwidth fit the device's low-voltage operating characteristics. Its two independent channels support stereo or balanced signal paths without requiring two separate packages. The 525 kHz gain-bandwidth product supports audio-band amplification, while the 8 V ceiling permits operation from a compact supply below that limit. Keep input and feedback impedances appropriate for low-noise operation, and confirm output swing and drive capability at the intended load. An RC network may be added at each input for impedance limiting and high-frequency noise control.
Önerilen
General-Purpose Active Filter
The TLV2332IP is appropriate for first- or second-order active filters built around its two amplifier channels. The 525 kHz gain-bandwidth product provides useful closed-loop bandwidth for low-frequency cutoff and center-frequency calculations, while low input bias current reduces errors with high-impedance RC networks. Each channel may implement a different filter section, allowing a dual-stage low-pass, high-pass, or band-pass arrangement on one PCB. Calculate resistor tolerances, capacitor stability, and noise gain using the datasheet's stated gain-bandwidth and output-drive characteristics. Keep the timing capacitors close to their associated pins to limit parasitic effects.
Önerilen
Industrial Control Interface
The TLV2332IP can condition low-level control signals in industrial equipment when its exact operating-temperature suffix is acceptable for the installation. One channel may amplify a feedback or command signal, while the other buffers a reference for an ADC or comparator. The dual PDIP package reduces component count on through-hole control boards, and the 525 kHz bandwidth covers many slow industrial control loops. Confirm the suffix-specific temperature rating, supply limits, and electrical characteristics before production release. Use stable reference points, controlled grounding, and supply-decoupling close to the IC to prevent switching transients from affecting the measured signal.
Önerilen
Voltage Buffer and Level Interface
The TLV2332IP can serve as a voltage buffer when the source presents a load that would otherwise distort a divider or measurement node. Its low input bias current helps preserve the voltage across high-impedance networks, and the dual configuration allows simultaneous buffering of a signal and reference. The 525 kHz gain-bandwidth product is suitable for modest closed-loop bandwidth and avoids unnecessary complexity for slow control signals. Confirm that the buffered voltage and output excursions remain within the common-mode and output-swing limits. Use a resistor near the output when driving capacitive loads or long PCB traces.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: TLV2332IP — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | TLV2332IPG4 | TLV2332IPE4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-8 | PDIP-8 | PDIP-8 |
| Number of Channels | 2 channels | 2 channels | 2 channels |
| Maximum Supply Voltage | 8 V | 8 V | 8 V |
| Gain-Bandwidth Product | 525 kHz | 525 kHz | 525 kHz |
| Process Technology | LinCMOS | LinCMOS | LinCMOS |
| Power Class | Low-voltage medium-power | Low-voltage medium-power | Low-voltage medium-power |
| Input Bias Current | Low input bias current | Low input bias current | Low input bias current |
| General-Purpose Classification | Standard general-purpose amplifier | Standard general-purpose amplifier | Standard general-purpose amplifier |
| Special Ordering Feature | Base TLV2332IP ordering code | G4 ordering code | E4 ordering code |
Ana Farklılayıcılar
- Maintains the same core voltage and bandwidth ratings as the target (karşılaştırma:TLV2332IPG4)
- Provides a direct same-footprint sourcing option (karşılaştırma:TLV2332IPE4)
- Combines two general-purpose amplifier channels in one through-hole package (karşılaştırma:TLV2332IPG4)
Tasarım Notları
Place the supply-decoupling network close to pins 4 and 8, with the shortest practical return path to the ground reference. Because this is a single-supply-capable device, connect pin 4 to the circuit's ground reference and ensure that signal excursions remain inside the specified common-mode range. Verify the complete operating supply range, input limits, output swing, and output-current capability from the manufacturer datasheet rather than assuming that the 8 V ceiling defines every permitted condition.
Route the two amplifier channels with short feedback paths and keep high-impedance input nodes physically small to reduce leakage, interference, and parasitic capacitance. Place input and feedback resistors close to their associated pins, and avoid sharing narrow copper paths between sensitive input and output nets. For a dual package, maintain consistent grounding under both channels because unequal return paths can degrade channel-to-channel performance even when each amplifier is configured correctly.
Do not allow either input of an unused channel to float. Tie the unused amplifier as a voltage follower with its input connected to a stable common-mode point inside the operating range, following the unused-circuit guidance in the manufacturer datasheet. Also avoid substituting the 8-pin TSSOP TLV2332 order code for this PDIP footprint, and do not apply an 8 V rail without checking absolute maximum and operating-limit conditions.
Uyumluluk Bilgisi
The manufacturer product page and datasheet landing pages do not provide explicit compliance results in the supplied records. The suffix-specific qualification and environmental requirements must be checked on the Texas Instruments part-details page before production release.