TLV2455ID - 6V Quad Rail-to-Rail Op Amp | Texas Instruments
MPN: TLV2455ID ✓ AktifTLV2455ID Genel Bakış
An operational amplifier is a voltage-gain element used to amplify small differential signals. The TLV2455 belongs to the linear-amplifier family within analog integrated circuits and signal-chain electronics. Rail-to-rail input operation allows the amplifier to sense signals near the lower and upper supply limits, while rail-to-rail output operation increases usable output range in low-voltage systems. These characteristics are particularly useful when signal levels approach the available supply voltage.
The principal TLV2455 features include four amplifier channels, 220 kHz gain-bandwidth product, 23 uA per-channel quiescent current, rail-to-rail input and output stages, and an operational shutdown function. The 220 kHz gain-bandwidth product supports small-signal bandwidth in the hundreds-of-kilohertz range, depending on closed-loop gain and output loading. The low channel current makes the device appropriate for portable, battery-powered, and distributed sensing systems where each active channel adds to the total power budget.
Each amplifier implements an operational-amplifier architecture with differential inputs and a single output. Feedback determines the closed-loop gain and bandwidth, while the open-loop gain and unity-gain bandwidth establish the practical operating range. Shutdown support allows a system designer to reduce consumption when a portion of the analog front end is not needed. Designers should account for enable timing and signal states during shutdown transitions to avoid unwanted output transients.
Typical uses include low-power sensor conditioning, battery-operated measurement instruments, portable audio and communication equipment, current or voltage monitoring, and general-purpose analog signal chains. Because all four amplifiers are integrated in one package, the TLV2455ID can replace four separate single or dual amplifier packages when a design requires four channels and a common supply.
PCB design should place each decoupling capacitor close to its associated supply and ground pins, minimize feedback-loop area, and route sensitive input and output nets away from switching nodes. Stable operation also depends on suitable load and output-capacitance conditions; consult the manufacturer datasheet for the exact limits before adding large capacitors directly to an output.
This product page combines manufacturer specifications, practical circuit guidance, package information, and qualified drop-in comparison data to accelerate component selection and PCB implementation. It also distinguishes verified electrical facts from parameters that require design-specific confirmation.
Drop-in alternatifler için TLV2455ID — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller TLV2455ID (aynı form faktörü ve ayağa oturma).
TLV2455AID
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
TLV2455ID Maksimum Değerlendirmeler & Elektriksel Özellikler
| Number of Amplifier Channels | 4 channels |
| Maximum Supply Voltage | 6 V |
| Durağan Akım | 23 uA per channel |
| Gain-Bandwidth Product | 220 kHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Voltage Swing | Rail-to-rail |
| Shutdown Function | Yes |
| Paket | 16-pin SOIC |
| Montaj Türü | Surface mount |
| Product Classification | General-purpose amplifier |
TLV2455ID 16-pin soic Pin Yapısı Kılavuzu
TLV2455ID (16-pin soic paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: TLV2455ID.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
TLV2455ID için uygundur 6 uygulamas: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Process Monitoring, Battery Management Monitoring, Portable Audio Signal Conditioning, Communication Equipment Interface.
Battery-Powered Sensor Conditioning
The TLV2455ID fits low-power sensor interfaces because each of its four amplifier channels has 23 uA of quiescent current, while rail-to-rail inputs help process signals near the supply limits. Four integrated channels can condition outputs from multiple sensors without requiring four separate packages. The 220 kHz gain-bandwidth product is suitable for moderate-bandwidth measurement signals rather than high-frequency waveform work. Use shutdown during inactive intervals and verify enable sequencing to prevent unnecessary current draw or transient outputs.
Önerilen
Portable Medical Monitoring
The TLV2455ID can support portable biomedical monitoring front ends where four low-current amplifier channels reduce component count and board area. Rail-to-rail input and output stages make the device useful for sensor signals and analog outputs that operate close to the available supply range. Its 23 uA per-channel quiescent current supports low-power operation, while shutdown can disable the analog section when monitoring is paused. Medical-system designers must separately assess isolation, leakage, safety, and qualification requirements.
Önerilen
Industrial Process Monitoring
The four-channel TLV2455ID is applicable to industrial process monitoring where pressure, temperature, and level sensors require local amplification. Rail-to-rail inputs help preserve signal integrity when sensor outputs span much of the sensor amplifier's supply range, and the 220 kHz gain-bandwidth product supports low-frequency process signals and control-loop feedback. The 16-pin SOIC simplifies board integration, but the layout should separate sensitive amplifier traces from motors, relays, and switching-converter nodes.
Önerilen
Battery Management Monitoring
TLV2455ID channels can amplify voltage, current, and temperature-related signals around a battery-management system. The 23 uA per-channel quiescent current is useful when every milliamp of operating demand affects run time, and the integrated four-channel arrangement provides a compact analog conditioning block. Rail-to-rail operation supports signal ranges near the system supply. The shutdown input should be managed carefully so that measurement channels are stable before control logic interprets their outputs.
Önerilen
Portable Audio Signal Conditioning
The TLV2455ID can provide low-level gain and buffering in portable audio-control or headphone-related circuits when four low-current channels are required. Rail-to-rail input and output stages maximize signal range in compact systems operating from a limited supply, and the 220 kHz gain-bandwidth product is appropriate for audio-band control and monitoring paths. Designers should verify output drive, noise, stability with the selected load, and headroom against their audio requirements before finalizing the analog path.
Önerilen
Communication Equipment Interface
The TLV2455ID can condition low-level signals in compact communication equipment where four amplifier channels and low supply current are more important than very high bandwidth. Rail-to-rail inputs support detection and conditioning near the supply rails, while the shutdown function permits controlled operation during inactive transmit or receive states. The 220 kHz gain-bandwidth product suits baseband control and monitoring loops. RF and high-speed data paths require separate devices with substantially higher bandwidth and validated noise performance.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: TLV2455ID — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | TLV2455AID |
|---|---|---|
| Package | 16-SOIC | 16-SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Number of Amplifier Channels | 4 channels | 4 channels |
| Maximum Supply Voltage | 6 V | 6 V |
| Gain-Bandwidth Product | 220 kHz | 220 kHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Voltage Swing | Rail-to-rail | Rail-to-rail |
| Shutdown Function | Yes | Yes |
Ana Farklılayıcılar
- Four integrated channels with low quiescent current (karşılaştırma:TLV2455AID)
- Rail-to-rail input and output operation (karşılaştırma:TLV2455AID)
- Direct integration of shutdown control (karşılaştırma:TLV2455AID)
Tasarım Notları
Place the supply decoupling capacitor close to the device power pins and connect the ground return to the ground plane with a short, low-inductance path. Route each non-inverting input away from switching nodes, relay contacts, and high-current traces. Keep feedback components adjacent to their associated amplifier pins and avoid routing input and output traces in parallel, particularly when the TLV2455ID drives a capacitive or dynamic load.
Budget the four amplifier channels separately: the manufacturer specifies 23 uA of quiescent current per channel, before output-current and dynamic-load contributions. Shutdown can reduce consumption when part of the signal chain is inactive, but the external circuitry must maintain defined input and output states during transitions. Confirm the complete supply range, common-mode limits, output swing, and absolute maximum ratings in the manufacturer datasheet for the actual operating condition.
The 220 kHz gain-bandwidth product must be considered together with the selected closed-loop gain and required phase margin. Avoid directly driving a long capacitive load because output-capacitance limits can affect stability and transient response. For sensor inputs, use guarding or shielding where needed, keep source impedances balanced, and place input filtering components close to the amplifier to minimize pickup and leakage effects.
Uyumluluk Bilgisi
Compliance declarations for the exact TLV2455ID ordering code require confirmation in the manufacturer product documentation.