Texas Instruments

TLV2455ID - 6V Quad Rail-to-Rail Op Amp | Texas Instruments

N.º de pieza: TLV2455ID ✓ Activo
6 V Vdss 23 uA per channel Id 16-pin SOIC Package
MOQ: 1 |

TLV2455ID Descripción general

Texas Instruments TLV2455ID is a quad, rail-to-rail input and output operational amplifier with shutdown, a 6 V maximum supply, 220 kHz gain-bandwidth product, and 23 uA per channel of quiescent current. The device is packaged in a 16-pin SOIC for surface-mount instrumentation, sensor, and low-power signal-processing systems. Its four amplifiers combine low supply current with input and output swing close to the supply rails.

An operational amplifier is a voltage-gain element used to amplify small differential signals. The TLV2455 belongs to the linear-amplifier family within analog integrated circuits and signal-chain electronics. Rail-to-rail input operation allows the amplifier to sense signals near the lower and upper supply limits, while rail-to-rail output operation increases usable output range in low-voltage systems. These characteristics are particularly useful when signal levels approach the available supply voltage.

The principal TLV2455 features include four amplifier channels, 220 kHz gain-bandwidth product, 23 uA per-channel quiescent current, rail-to-rail input and output stages, and an operational shutdown function. The 220 kHz gain-bandwidth product supports small-signal bandwidth in the hundreds-of-kilohertz range, depending on closed-loop gain and output loading. The low channel current makes the device appropriate for portable, battery-powered, and distributed sensing systems where each active channel adds to the total power budget.

Each amplifier implements an operational-amplifier architecture with differential inputs and a single output. Feedback determines the closed-loop gain and bandwidth, while the open-loop gain and unity-gain bandwidth establish the practical operating range. Shutdown support allows a system designer to reduce consumption when a portion of the analog front end is not needed. Designers should account for enable timing and signal states during shutdown transitions to avoid unwanted output transients.

Typical uses include low-power sensor conditioning, battery-operated measurement instruments, portable audio and communication equipment, current or voltage monitoring, and general-purpose analog signal chains. Because all four amplifiers are integrated in one package, the TLV2455ID can replace four separate single or dual amplifier packages when a design requires four channels and a common supply.

PCB design should place each decoupling capacitor close to its associated supply and ground pins, minimize feedback-loop area, and route sensitive input and output nets away from switching nodes. Stable operation also depends on suitable load and output-capacitance conditions; consult the manufacturer datasheet for the exact limits before adding large capacitors directly to an output.

This product page combines manufacturer specifications, practical circuit guidance, package information, and qualified drop-in comparison data to accelerate component selection and PCB implementation. It also distinguishes verified electrical facts from parameters that require design-specific confirmation.

Alternativas directas para TLV2455ID — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con TLV2455ID (mismo factor de forma y huella).

TLV2455AID

✅ Sustitución directa
📦 16-SOIC
Same 16-SOIC footprint, 6 V maximum supply, and 220 kHz gain-bandwidth product, producing 0 V and 0% differences in those listed ratings; other electrical-limit differences require datasheet confirmation.

📋 Alternativa de referencia (no en el catálogo)

TLV2455ID Valores máximos y características eléctricas

Number of Amplifier Channels 4 channels
Maximum Supply Voltage 6 V
Corriente en reposo 23 uA per channel
Gain-Bandwidth Product 220 kHz
Input Common-Mode Range Rail-to-rail
Output Voltage Swing Rail-to-rail
Shutdown Function Yes
Encapsulado 16-pin SOIC
Tipo de montaje Surface mount
Product Classification General-purpose amplifier

Guía de configuración de pines de TLV2455ID 16-pin soic

Configuración de pines para TLV2455ID (encapsulado 16-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 16-pin soic para TLV2455ID

No hay datos detallados de patillaje disponibles para TLV2455ID.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

TLV2455ID es adecuado para 6 aplicacións: Battery-Powered Sensor Conditioning, Portable Medical Monitoring, Industrial Process Monitoring, Battery Management Monitoring, Portable Audio Signal Conditioning, Communication Equipment Interface.

🔋

Battery-Powered Sensor Conditioning

The TLV2455ID fits low-power sensor interfaces because each of its four amplifier channels has 23 uA of quiescent current, while rail-to-rail inputs help process signals near the supply limits. Four integrated channels can condition outputs from multiple sensors without requiring four separate packages. The 220 kHz gain-bandwidth product is suitable for moderate-bandwidth measurement signals rather than high-frequency waveform work. Use shutdown during inactive intervals and verify enable sequencing to prevent unnecessary current draw or transient outputs.

💊

Portable Medical Monitoring

The TLV2455ID can support portable biomedical monitoring front ends where four low-current amplifier channels reduce component count and board area. Rail-to-rail input and output stages make the device useful for sensor signals and analog outputs that operate close to the available supply range. Its 23 uA per-channel quiescent current supports low-power operation, while shutdown can disable the analog section when monitoring is paused. Medical-system designers must separately assess isolation, leakage, safety, and qualification requirements.

🏭

Industrial Process Monitoring

The four-channel TLV2455ID is applicable to industrial process monitoring where pressure, temperature, and level sensors require local amplification. Rail-to-rail inputs help preserve signal integrity when sensor outputs span much of the sensor amplifier's supply range, and the 220 kHz gain-bandwidth product supports low-frequency process signals and control-loop feedback. The 16-pin SOIC simplifies board integration, but the layout should separate sensitive amplifier traces from motors, relays, and switching-converter nodes.

⚡

Battery Management Monitoring

TLV2455ID channels can amplify voltage, current, and temperature-related signals around a battery-management system. The 23 uA per-channel quiescent current is useful when every milliamp of operating demand affects run time, and the integrated four-channel arrangement provides a compact analog conditioning block. Rail-to-rail operation supports signal ranges near the system supply. The shutdown input should be managed carefully so that measurement channels are stable before control logic interprets their outputs.

🎧

Portable Audio Signal Conditioning

The TLV2455ID can provide low-level gain and buffering in portable audio-control or headphone-related circuits when four low-current channels are required. Rail-to-rail input and output stages maximize signal range in compact systems operating from a limited supply, and the 220 kHz gain-bandwidth product is appropriate for audio-band control and monitoring paths. Designers should verify output drive, noise, stability with the selected load, and headroom against their audio requirements before finalizing the analog path.

🌐

Communication Equipment Interface

The TLV2455ID can condition low-level signals in compact communication equipment where four amplifier channels and low supply current are more important than very high bandwidth. Rail-to-rail inputs support detection and conditioning near the supply rails, while the shutdown function permits controlled operation during inactive transmit or receive states. The 220 kHz gain-bandwidth product suits baseband control and monitoring loops. RF and high-speed data paths require separate devices with substantially higher bandwidth and validated noise performance.

What is the TLV2455ID?
The TLV2455ID is a Texas Instruments quad operational amplifier with rail-to-rail input and output stages, shutdown support, a 220 kHz gain-bandwidth product, and 23 uA of quiescent current per channel. According to the manufacturer product page, it operates from a maximum supply of 6 V and is intended for low-power, general-purpose analog signal processing in a 16-pin SOIC package.
What are the key specifications of TLV2455ID that engineers should know?
The TLV2455ID combines four rail-to-rail operational-amplifier channels, 23 uA per channel of quiescent current, a 220 kHz gain-bandwidth product, and a 6 V maximum supply. Texas Instruments identifies the device as a low-quiescent-current quad amplifier with shutdown. These parameters place it between general-purpose precision and micropower applications where four channels, rail-to-rail signal handling, and controlled supply consumption are important.
Where can I download the TLV2455ID datasheet PDF?
The official TLV2455ID documentation is available through the Texas Instruments TLV2455 product page at https://www.ti.com/product/TLV2455. The manufacturer product page provides the datasheet, ordering information, parameters, and family documentation. Use that document to confirm the complete electrical limits, pin functions, recommended operating conditions, shutdown behavior, and package drawings before releasing a production PCB.
Where can I find the TLV2455ID pinout?
The TLV2455ID pinout is shown in the pin-configuration section of the manufacturer datasheet for the 16-pin SOIC package. The TLV2455ID suffix identifies the quad SOIC configuration, while the device family includes amplifier inputs, outputs, power pins, and shutdown-control functions. Use the numbered package drawing for PCB pads and verify every net against the specific ordering code before layout release.
What is the difference between TLV2455ID and TLV2455AID?
Both TLV2455ID and TLV2455AID are Texas Instruments quad rail-to-rail operational amplifiers in 16-pin SOIC packages, and both operate with a 6 V maximum supply and 220 kHz gain-bandwidth product. Their electrically meaningful family-level differences require confirmation from their individual datasheets. The TLV2455AID is the qualified drop-in candidate listed here, with a 0 V difference in supply rating and 0% difference in gain-bandwidth product.
Can TLV2455AID replace TLV2455ID as a drop-in replacement?
TLV2455AID is a candidate drop-in replacement for TLV2455ID because it uses the same 16-pin SOIC package and the listed family specifications show the same 6 V maximum supply and 220 kHz gain-bandwidth product. Before substitution, compare input offset, bias current, output drive, noise, shutdown timing, and absolute maximum ratings in both manufacturer datasheets. Board changes are not expected if those parameters meet the original design requirements.
When should I choose TLV2455ID over TLV2455AID?
Choose TLV2455ID when it is the exact ordering code specified by the original circuit, qualification documentation, or approved BOM. Choose TLV2455AID when a new production build needs a qualified same-footprint alternative and its latest datasheet limits satisfy the application. Both parts provide four channels, 23 uA-class quiescent-current operation, rail-to-rail input and output behavior, shutdown, and a 220 kHz gain-bandwidth product.
Is TLV2455ID suitable for battery-powered sensor conditioning?
Yes, the TLV2455ID is well suited to battery-powered sensor conditioning because each amplifier consumes 23 uA of quiescent current and the four channels share one 6 V-class supply. Rail-to-rail inputs are useful when sensor outputs occupy a substantial portion of the available signal range. The shutdown function can further control consumption when the measurement front end is inactive, subject to correct enable sequencing.
What is the gain-bandwidth product of TLV2455ID?
The TLV2455ID has a gain-bandwidth product of 220 kHz, according to the Texas Instruments product description. This specification defines the relationship between small-signal closed-loop bandwidth and noise gain for the operational amplifier. Actual usable bandwidth still depends on the selected feedback network, operating gain, load, output-capacitance limits, and required phase margin, so simulation and datasheet guidance remain necessary.
How much current does TLV2455ID consume?
The TLV2455ID consumes 23 uA of quiescent current per amplifier channel, as specified by the manufacturer. Four active channels therefore establish a principal static-current budget for the integrated amplifier section. Actual supply current varies with input voltage, output loading, shutdown state, and operating frequency. Use shutdown when a channel group is not required to reduce overall system consumption.
Where can I buy TLV2455ID online and what is the price?
Use the Request a Quote form on this page to request current TLV2455ID availability, unit pricing, and lead time. The form allows the exact 16-pin SOIC ordering code to be included in the request, reducing ambiguity between the TLV2455ID and TLV2455AID variants. Commercial terms should be confirmed at the time of quotation because component pricing and supply status can change.
What is the lead time for TLV2455ID?
Current TLV2455ID lead time depends on supplier inventory, manufacturing status, and order quantity. Submit the exact MPN through the Request a Quote form on this page to request a dated lead-time estimate and current stock position. For new designs, also confirm the ordering-code suffix, assembly package, quantity, and delivery requirements before committing the production schedule.
Is TLV2455ID in stock?
Stock status for TLV2455ID changes with market demand and order volume. Use the Request a Quote form on this page to obtain the current availability for the exact TLV2455ID ordering code. When requesting a quotation, specify the required quantity, acceptable pack format, production date code policy, and delivery location so the response reflects the actual build schedule.
What is the best cross-brand equivalent for TLV2455ID?
No cross-brand equivalent is established for the TLV2455ID by the available manufacturer and cross-reference information. A defensible replacement must match the 16-pin SOIC footprint, four-amplifier channel count, shutdown architecture, 6 V-class supply operation, and approximately 23 uA per-channel current draw. Request a manufacturer cross-reference review or consult the appropriate device datasheets before treating any competitor part as a drop-in substitution.
What can replace TLV2455ID?
TLV2455AID is the qualified drop-in candidate identified for TLV2455ID, with the same 16-pin SOIC package, four amplifier channels, 6 V maximum supply, and 220 kHz gain-bandwidth product. Other substitutions should be accepted only after checking pin functions, shutdown polarity, input and output ranges, offset voltage, bias current, output drive, noise, stability, and temperature limits against the original circuit requirements.

Datos de referencia de ingeniería para TLV2455ID — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the TLV2455ID when it is the exact part specified by an established design, approved BOM, or qualification record. It provides four rail-to-rail amplifier channels, 23 uA of quiescent current per channel, a 220 kHz gain-bandwidth product, shutdown, and a 16-pin SOIC package. Choose the TLV2455AID when it is the approved family alternative and its individual datasheet confirms every required offset, noise, drive, stability, and temperature parameter. Neither choice should be based on package appearance alone: verify the exact pin functions, shutdown polarity, operating ranges, and production quantity. If neither TI ordering code satisfies the system requirements, use the manufacturer's cross-reference process to identify a genuinely pin-compatible candidate rather than forcing an electrically different amplifier into the same footprint.

Comparación con alternativas

Parámetro Este producto TLV2455AID
Package 16-SOIC 16-SOIC
Brand Texas Instruments Texas Instruments
Number of Amplifier Channels 4 channels 4 channels
Maximum Supply Voltage 6 V 6 V
Gain-Bandwidth Product 220 kHz 220 kHz
Input Common-Mode Range Rail-to-rail Rail-to-rail
Output Voltage Swing Rail-to-rail Rail-to-rail
Shutdown Function Yes Yes

Diferenciadores clave

  • Four integrated channels with low quiescent current (frente a TLV2455AID)
  • Rail-to-rail input and output operation (frente a TLV2455AID)
  • Direct integration of shutdown control (frente a TLV2455AID)

Notas de diseño

Place the supply decoupling capacitor close to the device power pins and connect the ground return to the ground plane with a short, low-inductance path. Route each non-inverting input away from switching nodes, relay contacts, and high-current traces. Keep feedback components adjacent to their associated amplifier pins and avoid routing input and output traces in parallel, particularly when the TLV2455ID drives a capacitive or dynamic load.

Budget the four amplifier channels separately: the manufacturer specifies 23 uA of quiescent current per channel, before output-current and dynamic-load contributions. Shutdown can reduce consumption when part of the signal chain is inactive, but the external circuitry must maintain defined input and output states during transitions. Confirm the complete supply range, common-mode limits, output swing, and absolute maximum ratings in the manufacturer datasheet for the actual operating condition.

The 220 kHz gain-bandwidth product must be considered together with the selected closed-loop gain and required phase margin. Avoid directly driving a long capacitive load because output-capacitance limits can affect stability and transient response. For sensor inputs, use guarding or shielding where needed, keep source impedances balanced, and place input filtering components close to the amplifier to minimize pickup and leakage effects.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

Compliance declarations for the exact TLV2455ID ordering code require confirmation in the manufacturer product documentation.

Datos verificados el: 2026-11-19 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

TLV2455ID datasheet TLV2455ID pinout TLV2455ID datasheet pdf TLV2455ID equivalent TLV2455ID replacement TLV2455ID cross reference TLV2455ID vs TLV2455AID TLV2455ID price TLV2455ID stock Texas Instruments TLV2455ID TLV2455ID 220kHz amplifier TLV2455ID 23uA low power 16-SOIC TLV2455ID pinout TLV2455ID sensor signal conditioning

Componentes & términos relacionados

Texas Instruments TLV2455ID TLV2455AID TLV2455 family quad operational amplifier operational amplifier analog integrated circuit linear amplifier rail-to-rail input rail-to-rail output RRIO gain-bandwidth product quiescent current shutdown function low-power signal processing battery-powered sensing industrial process monitoring portable medical monitoring battery management monitoring portable audio conditioning communication equipment interface 16-SOIC SOIC package family surface-mount package semiconductor
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ