TLV2622ID - 11MHz Dual RRO Op Amp | Texas Instruments
MPN: TLV2622ID ✓ AktifTLV2622ID Genel Bakış
A rail-to-rail-input/output operational amplifier is an analog signal-conditioning device designed to accept and produce voltages close to either supply rail. The TLV2622 belongs to the operational-amplifier hierarchy within analog ICs and mixed-signal semiconductors. Its rail-to-rail output can swing close to the positive and negative supply limits, while its input common-mode range includes the positive rail, making it useful for low-voltage sensors, portable equipment, and battery-powered systems.
The main features of the TLV2622ID include two amplifier channels, an 11 MHz gain-bandwidth product, approximately 800 uA of supply current per channel, and a 2.7 V minimum operating supply. These characteristics provide useful bandwidth for sensor interfaces, audio signal paths, and general-purpose filtering without requiring a high-voltage supply. The SOIC-8 package also supports conventional surface-mount assembly and provides a practical upgrade path for standard dual-amplifier layouts.
The family uses a CMOS operational-amplifier architecture optimized for low-voltage, low-power operation. Rail-to-rail output reduces the need for an output swing limited to a few volts below the supply, which is especially helpful when the next stage operates from the same low-voltage rail. Input bias current, offset voltage, noise density, slew rate, output-current capability, and stability information should be taken from the manufacturer datasheet when sizing high-impedance sources or driving demanding loads.
Typical uses include battery-powered sensor conditioning, industrial acquisition circuits, low-voltage audio channels, current sensing, ADC drivers, and portable medical or test equipment. In a sensor interface, the amplifier can buffer a sensor output before it reaches an ADC or comparator. In an active filter, the 11 MHz bandwidth provides useful speed margin for moderate-gain stages, although exact filter performance depends on resistor values, capacitor selection, noise, and stability.
For single-supply designs, treat the unused amplifier channel carefully. Its inputs should be connected to a defined common-mode voltage, normally a low-impedance point near ground, rather than left floating. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be kept away from switching nodes and high-current return paths.
This product page combines the manufacturer specifications, package and pin information, sourcing guidance, application-oriented design considerations, and a parameter comparison with qualified alternatives. It also highlights the electrical and layout decisions that determine whether the TLV2622ID can operate reliably in a compact, low-voltage analog signal chain.
Drop-in alternatifler için TLV2622ID — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller TLV2622ID (aynı form faktörü ve ayağa oturma) — farklı olan Gain-Bandwidth Product, Amplifier Type, Input Common-Mode Range, Operating Temperature Range, Output Swing.
TLV2623ID
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
TLV2462ID
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →TLV2772ID
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →TLV2702ID
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
TLV9062ID
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
TLV2622ID Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Dual operational amplifier |
| Channel Count | 2 channels |
| Maximum Supply Voltage | 5.5 V |
| Minimum Operating Supply Voltage | 2.7 V |
| Supply Current per Channel | Approximately 800 uA |
| Gain-Bandwidth Product | 11 MHz |
| Output Swing | Rail-to-rail |
| Input Common-Mode Range | Includes the positive supply rail |
| İşletim Sıcaklığı Aralığı | -40°C to +125°C |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
| Process Technology | CMOS |
| Automotive Qualification | Not stated for TLV2622ID |
| RoHS Compliance | Not stated |
| REACH Compliance | Not stated |
| Lead-Free Status | Not stated |
| Halogen-Free Status | Not stated |
TLV2622ID Pin Yapısı
| Pin 1 | OUTA — Channel A output |
| Pin 2 | IN A- — Channel A inverting input |
| Pin 3 | IN A+ — Channel A noninverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | IN B+ — Channel B noninverting input |
| Pin 6 | IN B- — Channel B inverting input |
| Pin 7 | OUTB — Channel B output |
| Pin 8 | V+ — Positive supply connection |
Tipik Uygulamalar
TLV2622ID için uygundur 6 uygulamas: Battery-Powered Sensor Conditioning, Low-Voltage ADC Signal Conditioning, Portable Audio Signal Path, Industrial Current Sensing, Active Filtering and Tone Control, Portable Medical and Test Equipment.
Battery-Powered Sensor Conditioning
The TLV2622ID fits low-voltage sensor interfaces because it operates from 2.7 V to 5.5 V, draws approximately 800 uA per channel, and provides rail-to-rail output with an input range that includes the positive rail. Place one channel as a unity-gain buffer between a sensor and an ADC or mixed-signal controller. The 11 MHz gain-bandwidth product leaves more bandwidth than the signal path typically requires, while the low-power operating point supports longer battery life. Check the sensor impedance, ADC input range, bias current, and settling time before finalizing the buffer configuration.
Önerilen
Low-Voltage ADC Signal Conditioning
The TLV2622ID can provide gain and isolation ahead of a low-voltage ADC when the source impedance would otherwise load the converter. Its 11 MHz gain-bandwidth product supports moderate closed-loop gains while remaining compatible with a 2.7 V minimum supply. Rail-to-rail output helps preserve dynamic range in 3.3 V systems by reducing the output-swing restriction of a conventional amplifier. Select feedback resistors for the required gain and verify the ADC acquisition time, amplifier settling behavior, input bias current, and output-capacitance stability.
Önerilen
Portable Audio Signal Path
The TLV2622ID is suitable for low-voltage audio buffering when the design requires two channels, a compact SOIC-8 footprint, and low supply current. Rail-to-rail output can improve utilization of a 3.3 V or 5 V analog rail, while the 11 MHz bandwidth provides useful headroom for audio-frequency amplification and filtering. The amplifier does not replace a dedicated audio power stage, but it can drive a high-impedance codec input or the input of a subsequent audio amplifier. Check noise, offset, output-current limits, and capacitive-load behavior in the final signal path.
Önerilen
Industrial Current Sensing
The TLV2622ID can amplify the small voltage produced by a current-sense shunt when the measurement system operates from a low-voltage rail. Its approximately 800 uA per-channel supply current reduces the burden on portable or distributed sensing equipment, and the 11 MHz bandwidth supports fast measurement loops. Use one channel for amplification and the other for gain balancing, filtering, or a reference buffer. The design must account for shunt common-mode voltage, amplifier input range, offset relative to the sensed current, resistor tolerance, and the input common-mode limits of the selected device.
Önerilen
Active Filtering and Tone Control
The TLV2622ID can implement first- or higher-order active filters in low-voltage embedded systems because its 11 MHz gain-bandwidth product provides useful bandwidth for moderate-gain stages. Its dual-channel architecture allows cascading sections or implementing paired signal-processing paths in one 8-pin SOIC package. Component tolerances, amplifier noise, gain error, and output-loading effects can influence the realized filter response. Validate the transfer function across temperature and supply variation, and confirm stability when the output drives the next stage or a capacitive cable.
Önerilen
Portable Medical and Test Equipment
The TLV2622ID is applicable to compact, low-power measurement instruments that buffer low-level analog signals before digitization. Operation from 2.7 V supports lithium-battery systems, while approximately 800 uA per channel is useful for reducing average system power. The rail-to-rail output helps preserve signal range on a restricted supply, and the 11 MHz bandwidth can support fast settling in measurement chains. Medical or laboratory use still requires system-level validation, including leakage, noise, calibration stability, isolation, and applicable regulatory requirements.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: TLV2622ID — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | TLV2623ID | TLV2462ID | TLV2772ID | TLV2702ID | TLV9062ID |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Channel Count | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Gain-Bandwidth Product | 11 MHz | 11 MHz | 10 MHz | 7.5 MHz | 5.5 MHz | 11 MHz |
Ana Farklılayıcılar
- Higher bandwidth than the lower-speed family alternatives (karşılaştırma:TLV2702ID)
- Approximately 9% higher bandwidth than the TLV2462ID (karşılaştırma:TLV2462ID)
- Matches the identified 11 MHz, 800 uA-per-channel class (karşılaştırma:TLV9062ID)
Tasarım Notları
Do not leave either operational-amplifier input floating. Tie the unused channel's inputs to a defined common-mode reference, preferably through the feedback arrangement appropriate for a stable unity-gain buffer. Verify that the reference remains within the TLV2622ID input common-mode range at every supply voltage. Also observe the 2.7 V to 5.5 V supply limits and do not treat the 5.5 V rating as a transient overvoltage allowance.
Place the supply bypass capacitor directly between the V+ and V- pins, with the shortest practical ground return. Keep the SOIC footprint on the same ground plane as the analog source and destination when possible. Route feedback components close to the relevant amplifier inputs and outputs to minimize parasitic capacitance in high-gain or fast-feedback nodes. A dedicated analog ground region may be appropriate, but avoid introducing return current through sensitive input nodes.
The 11 MHz gain-bandwidth product provides bandwidth headroom, but settling time and stability depend on closed-loop gain, noise gain, output loading, and feedback topology. Add an isolation resistor between the TLV2622ID output and a capacitive load when the manufacturer stability guidance calls for it. For ADC interfaces, calculate the required settling interval and verify it against the converter's acquisition time rather than relying only on the nominal gain-bandwidth figure.
Estimated: each channel contributes approximately 800 uA of supply current, so the dual device can draw approximately 1.6 mA before load current and bias-current effects. At a 3.3 V supply, this corresponds to approximately 5.28 mW of internal supply power using I = 800 uA per channel and V = 3.3 V. This estimate is not a substitute for the maximum supply-current specification and should be checked against the actual operating mode and manufacturer limits.
Uyumluluk Bilgisi
The reviewed manufacturer product page identifies the TLV2622 as an active dual operational amplifier but does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements for the TLV2622ID ordering code. Confirm these attributes in the current manufacturer product and quality documentation.