Texas Instruments

TLV2622ID - 11MHz Dual RRO Op Amp | Texas Instruments

MPN: TLV2622ID ✓ Hoạt động
5.5 V Vdss Approximately 800 uA Id 8-pin SOIC Package
MOQ: 1 |

TLV2622ID Tóm tắt

The Texas Instruments TLV2622ID is a dual, rail-to-rail-output CMOS operational amplifier rated for a 5.5 V maximum supply voltage and an 11 MHz gain-bandwidth product. Each channel draws approximately 800 uA, and the device is packaged in an 8-pin SOIC. The amplifier supports supply operation from 2.7 V to 5.5 V over an extended industrial temperature range of -40°C to +125°C.

A rail-to-rail-input/output operational amplifier is an analog signal-conditioning device designed to accept and produce voltages close to either supply rail. The TLV2622 belongs to the operational-amplifier hierarchy within analog ICs and mixed-signal semiconductors. Its rail-to-rail output can swing close to the positive and negative supply limits, while its input common-mode range includes the positive rail, making it useful for low-voltage sensors, portable equipment, and battery-powered systems.

The main features of the TLV2622ID include two amplifier channels, an 11 MHz gain-bandwidth product, approximately 800 uA of supply current per channel, and a 2.7 V minimum operating supply. These characteristics provide useful bandwidth for sensor interfaces, audio signal paths, and general-purpose filtering without requiring a high-voltage supply. The SOIC-8 package also supports conventional surface-mount assembly and provides a practical upgrade path for standard dual-amplifier layouts.

The family uses a CMOS operational-amplifier architecture optimized for low-voltage, low-power operation. Rail-to-rail output reduces the need for an output swing limited to a few volts below the supply, which is especially helpful when the next stage operates from the same low-voltage rail. Input bias current, offset voltage, noise density, slew rate, output-current capability, and stability information should be taken from the manufacturer datasheet when sizing high-impedance sources or driving demanding loads.

Typical uses include battery-powered sensor conditioning, industrial acquisition circuits, low-voltage audio channels, current sensing, ADC drivers, and portable medical or test equipment. In a sensor interface, the amplifier can buffer a sensor output before it reaches an ADC or comparator. In an active filter, the 11 MHz bandwidth provides useful speed margin for moderate-gain stages, although exact filter performance depends on resistor values, capacitor selection, noise, and stability.

For single-supply designs, treat the unused amplifier channel carefully. Its inputs should be connected to a defined common-mode voltage, normally a low-impedance point near ground, rather than left floating. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be kept away from switching nodes and high-current return paths.

This product page combines the manufacturer specifications, package and pin information, sourcing guidance, application-oriented design considerations, and a parameter comparison with qualified alternatives. It also highlights the electrical and layout decisions that determine whether the TLV2622ID can operate reliably in a compact, low-voltage analog signal chain.

Bộ thay thế dễ dàng lắp đặt cho TLV2622ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLV2622ID (cùng hình factor và footprint) — khác nhau ở Gain-Bandwidth Product, Amplifier Type, Input Common-Mode Range, Operating Temperature Range, Output Swing.

Texas Instruments
Gain-Bandwidth Product: 6.4 MHz
Input Common-Mode Range: Rail-to-rail input
Operating Temperature Range: -40 °C to +125 °C
So sánh với TLV2622ID →
Texas Instruments
Gain-Bandwidth Product: 5.1 MHz
Amplifier Type: Dual CMOS operational amplifier
So sánh với TLV2622ID →

TLV2623ID

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Adds shutdown functionality; bandwidth remains 11 MHz, subject to final pin-table verification

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2462ID

✅ Drop-In ⚠️ Thông số chưa được xác minh
Texas Instruments
📦 8-pin SOIC
Dual operational amplifier · 2 circuits · 6.4 MHz · 1.6 V/µs · 6 V · Rail-to-rail input · Rail-to-rail output

Liên hệ để biết giá

Xem tài liệu →

TLV2772ID

✅ Drop-In ⚠️ Thông số chưa được xác minh
Texas Instruments
📦 8-pin SOIC
Dual CMOS operational amplifier · 2 channels · 5.5 V · 2.7 V · 5.1 MHz · 10.5 V/us · Rail-to-rail output

Liên hệ để biết giá

Xem tài liệu →

TLV2702ID

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Gain-bandwidth product is 5.5 MHz versus 11 MHz for the TLV2622ID, a difference of approximately 50%

📋 Tham chiếu thay thế (không có trong danh mục)

TLV9062ID

✅ Drop-In
📦 8-pin SOIC
Uses the same dual RRO, 5 V, 11 MHz class and 800 uA per channel; final pin and limit comparison is required

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2622ID Tỷ lệ tối đa & tính chất điện

Amplifier Type Dual operational amplifier
Channel Count 2 channels
Maximum Supply Voltage 5.5 V
Minimum Operating Supply Voltage 2.7 V
Supply Current per Channel Approximately 800 uA
Gain-Bandwidth Product 11 MHz
Output Swing Rail-to-rail
Input Common-Mode Range Includes the positive supply rail
Khoảng nhiệt độ hoạt động -40°C to +125°C
Hộp 8-pin SOIC
Kiểu lắp đặt Surface mount
Process Technology CMOS
Automotive Qualification Not stated for TLV2622ID
RoHS Compliance Not stated
REACH Compliance Not stated
Lead-Free Status Not stated
Halogen-Free Status Not stated

Cấu hình chân TLV2622ID

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Chân 1 OUTA — Channel A output
Chân 2 IN A- — Channel A inverting input
Chân 3 IN A+ — Channel A noninverting input
Chân 4 V- — Negative supply connection
Chân 5 IN B+ — Channel B noninverting input
Chân 6 IN B- — Channel B inverting input
Chân 7 OUTB — Channel B output
Chân 8 V+ — Positive supply connection

Ứng dụng tiêu biểu

TLV2622ID phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Low-Voltage ADC Signal Conditioning, Portable Audio Signal Path, Industrial Current Sensing, Active Filtering and Tone Control, Portable Medical and Test Equipment.

🧩

Battery-Powered Sensor Conditioning

The TLV2622ID fits low-voltage sensor interfaces because it operates from 2.7 V to 5.5 V, draws approximately 800 uA per channel, and provides rail-to-rail output with an input range that includes the positive rail. Place one channel as a unity-gain buffer between a sensor and an ADC or mixed-signal controller. The 11 MHz gain-bandwidth product leaves more bandwidth than the signal path typically requires, while the low-power operating point supports longer battery life. Check the sensor impedance, ADC input range, bias current, and settling time before finalizing the buffer configuration.

📊

Low-Voltage ADC Signal Conditioning

The TLV2622ID can provide gain and isolation ahead of a low-voltage ADC when the source impedance would otherwise load the converter. Its 11 MHz gain-bandwidth product supports moderate closed-loop gains while remaining compatible with a 2.7 V minimum supply. Rail-to-rail output helps preserve dynamic range in 3.3 V systems by reducing the output-swing restriction of a conventional amplifier. Select feedback resistors for the required gain and verify the ADC acquisition time, amplifier settling behavior, input bias current, and output-capacitance stability.

🎧

Portable Audio Signal Path

The TLV2622ID is suitable for low-voltage audio buffering when the design requires two channels, a compact SOIC-8 footprint, and low supply current. Rail-to-rail output can improve utilization of a 3.3 V or 5 V analog rail, while the 11 MHz bandwidth provides useful headroom for audio-frequency amplification and filtering. The amplifier does not replace a dedicated audio power stage, but it can drive a high-impedance codec input or the input of a subsequent audio amplifier. Check noise, offset, output-current limits, and capacitive-load behavior in the final signal path.

🏭

Industrial Current Sensing

The TLV2622ID can amplify the small voltage produced by a current-sense shunt when the measurement system operates from a low-voltage rail. Its approximately 800 uA per-channel supply current reduces the burden on portable or distributed sensing equipment, and the 11 MHz bandwidth supports fast measurement loops. Use one channel for amplification and the other for gain balancing, filtering, or a reference buffer. The design must account for shunt common-mode voltage, amplifier input range, offset relative to the sensed current, resistor tolerance, and the input common-mode limits of the selected device.

📡

Active Filtering and Tone Control

The TLV2622ID can implement first- or higher-order active filters in low-voltage embedded systems because its 11 MHz gain-bandwidth product provides useful bandwidth for moderate-gain stages. Its dual-channel architecture allows cascading sections or implementing paired signal-processing paths in one 8-pin SOIC package. Component tolerances, amplifier noise, gain error, and output-loading effects can influence the realized filter response. Validate the transfer function across temperature and supply variation, and confirm stability when the output drives the next stage or a capacitive cable.

💊

Portable Medical and Test Equipment

The TLV2622ID is applicable to compact, low-power measurement instruments that buffer low-level analog signals before digitization. Operation from 2.7 V supports lithium-battery systems, while approximately 800 uA per channel is useful for reducing average system power. The rail-to-rail output helps preserve signal range on a restricted supply, and the 11 MHz bandwidth can support fast settling in measurement chains. Medical or laboratory use still requires system-level validation, including leakage, noise, calibration stability, isolation, and applicable regulatory requirements.

Tóm tắt các sản phẩm được đề xuất

TLV2622ID Texas Instruments Được sử dụng trong: Battery-Powered Sensor Conditioning, Low-Voltage ADC Signal Conditioning, Portable Audio Signal Path, Industrial Current Sensing, Active Filtering and Tone Control, Portable Medical and Test Equipment TLV2622IDR Related orderable family variant Được sử dụng trong: Battery-Powered Sensor Conditioning, Low-Voltage ADC Signal Conditioning, Portable Audio Signal Path, Industrial Current Sensing, Active Filtering and Tone Control, Portable Medical and Test Equipment
What are the key specifications of TLV2622ID that engineers should know?
The TLV2622ID is a dual, 5.5 V maximum, 11 MHz rail-to-rail-output operational amplifier with approximately 800 uA of supply current per channel. According to the Texas Instruments product page and manufacturer datasheet, it operates from 2.7 V to 5.5 V, supports an input range that includes the positive rail, and is offered in an 8-pin SOIC package. It is intended for low-voltage signal conditioning, buffering, filtering, and portable analog systems.
What is the operating voltage of TLV2622ID?
The TLV2622ID operates from 2.7 V to 5.5 V. According to the Texas Instruments product page and manufacturer datasheet, 5.5 V is the maximum supply rating. The 2.7 V minimum makes the amplifier suitable for 3.3 V systems, while the maximum rating allows use in 5 V systems without exceeding the absolute supply limit. Decoupling and input/output voltage limits must still be respected.
Is TLV2622ID rail-to-rail input and output?
The TLV2622ID provides rail-to-rail output and an input common-mode range that includes the positive supply rail. According to the Texas Instruments family description, this allows the amplifier to sense and reproduce signals near the upper rail better than a conventional amplifier restricted to a range below both supplies. The negative-rail behavior and exact input range should be checked in the manufacturer datasheet for the selected operating conditions.
What is the gain-bandwidth product of TLV2622ID?
The TLV2622ID has an 11 MHz gain-bandwidth product for each amplifier channel. According to the Texas Instruments product page and manufacturer datasheet, this bandwidth supports higher-speed closed-loop operation than lower-bandwidth general-purpose amplifiers. In a practical filter or amplifier, the usable bandwidth also depends on closed-loop gain, noise, stability, load, and the selected external components.
Where can I download the TLV2622ID datasheet PDF?
The official TLV2622 family datasheet is available from Texas Instruments at https://www.ti.com/lit/gpn/TLV2622. According to the manufacturer, this document contains the family electrical characteristics, package drawings, pin descriptions, and application information. Use the manufacturer document for design decisions because the exact TLV2622ID limits, test conditions, and ordering information must be checked against the selected package and grade.
Where can I find the TLV2622ID pinout?
The TLV2622ID pinout is shown in the top-view package drawing in the Texas Instruments family datasheet at https://www.ti.com/lit/gpn/TLV2622. The device uses an 8-pin SOIC with two amplifier channels, supply pins, and no-connect positions where applicable. Assign PCB tracks directly from the manufacturer pin-description table so channel assignments, supply polarity, and NC pins match the exact ordering code.
Can TLV9062ID replace TLV2622ID in the same SOIC-8 footprint?
The TLV9062ID can serve as a candidate replacement because it is also an 8-pin SOIC dual rail-to-rail operational amplifier, and its appearance in the manufacturer-family comparison information confirms broadly similar low-voltage RRO functionality. However, a drop-in decision still requires checking the exact pin table, supply limits, offset, noise, slew rate, stability, and shutdown or enable behavior. The Texas Instruments cross-reference resources should be used for an approved production substitution.
TLV2622ID vs TLV2623ID - which is better for a low-voltage design?
Choose the TLV2622ID when the design requires a conventional dual amplifier without a shutdown function, and evaluate the TLV2623ID when independent shutdown is important. According to the Texas Instruments family datasheet, both are low-power wide-bandwidth single-supply operational amplifiers, but the family includes functional shutdown variants. Because shutdown implementation can alter pin availability or board-control requirements, confirm the exact package drawing before treating either device as interchangeable.
When should I choose TLV2622ID over a lower-bandwidth dual op amp?
Choose the TLV2622ID when signal bandwidth, response time, or filtering requirements exceed those of a lower-bandwidth dual amplifier. Its 11 MHz gain-bandwidth product provides more than 10 times the bandwidth of a typical 1 MHz micropower dual amplifier, while approximately 800 uA per channel preserves a low-power design target. The TLV2622ID is especially attractive when operating voltage must remain below 5.5 V.
Is TLV2622ID suitable for 3.3 V sensor interfaces?
Yes, the TLV2622ID is suitable for many 3.3 V sensor-interface circuits because its minimum operating supply is 2.7 V and its maximum rating is 5.5 V. According to the Texas Instruments product page, the amplifier has rail-to-rail output and an input range that includes the positive rail. Confirm the sensor output range, ADC input limits, offset, noise, capacitive-load stability, and settling requirements before finalizing the circuit.
What can replace TLV2622ID on an existing 8-pin SOIC board?
The strongest replacement candidates are dual low-voltage RRO amplifiers in the standard 8-pin SOIC footprint, including the TLV9062ID and compatible Texas Instruments family members. According to Texas Instruments cross-reference guidance, drop-in status depends on pin, package, and parameter matching rather than package dimensions alone. Verify the pin table, supply range, electrical limits, and application requirements before releasing any substitute to production.
What is the best cross-brand equivalent for TLV2622ID?
No cross-brand equivalent can be certified as a direct replacement from the manufacturer information reviewed for the TLV2622ID. A candidate should use an 8-pin SOIC, provide two rail-to-rail-output channels, support the required 2.7 V to 5.5 V supply range, and remain pin-compatible. Use the Texas Instruments cross-reference search for candidate generation, then validate offset, noise, bandwidth, slew rate, stability, and lifecycle requirements in the target circuit.
How much current does TLV2622ID consume?
The TLV2622ID consumes approximately 800 uA per amplifier channel under the manufacturer-described operating conditions. According to the Texas Instruments family description, this low supply current complements the 2.7 V minimum supply and 11 MHz bandwidth. Actual current depends on supply voltage, input voltage, output load, quiescent state, and operating temperature, so use the manufacturer datasheet for design-limit calculations.
Where to buy TLV2622ID online?
Use the Request a Quote form on this page to request TLV2622ID availability, packaging details, and a quotation. The form is the appropriate route for current commercial terms without relying on a potentially stale catalog figure. Quote requests should specify the exact TLV2622ID ordering code, required quantity, shipment destination, and delivery schedule so the manufacturer-supported supply chain can respond accurately.
What is the price and lead time of TLV2622ID?
Request current TLV2622ID pricing and lead time through the Request a Quote form on this page. According to Texas Instruments ordering information, the part is identified as an active dual operational amplifier in an 8-pin SOIC package. The quotation process establishes the commercial amount, production allocation, shipment terms, and date for the requested quantity rather than presenting a static price that may no longer reflect availability.
Is TLV2622ID in stock?
Current TLV2622ID inventory should be confirmed through the Request a Quote form on this page by entering the required quantity and destination. Stock levels can vary by package form, lot, and order date. A successful quote response provides the most useful confirmation for procurement because it connects the requested commercial quantity with an available shipment and lead-time commitment.

Dữ liệu tham khảo kỹ thuật cho TLV2622ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the TLV2622ID for a compact, low-voltage design that needs two RRO amplifier channels, an 11 MHz gain-bandwidth product, and approximately 800 uA per channel. It is a strong fit for 3.3 V sensor buffers, ADC conditioning, low-level current measurement, and general active-filter stages. Consider the TLV2623ID when a shutdown function is required, but verify its control and pin implementation before changing the schematic. The TLV2462ID is reasonable when slightly lower bandwidth is acceptable, while the TLV2772ID and TLV2702ID trade bandwidth for their respective lower-speed operating classes. The TLV9062ID is a close functional candidate identified in the same 5 V, 11 MHz, 800 uA-per-channel class. For every candidate, validate the exact pin table, input and output ranges, offset, noise, stability, load capability, temperature grade, and lifecycle status before treating it as a production drop-in replacement.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này TLV2623ID TLV2462ID TLV2772ID TLV2702ID TLV9062ID
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Channel Count 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Gain-Bandwidth Product 11 MHz 11 MHz 10 MHz 7.5 MHz 5.5 MHz 11 MHz

Bảo phân biệt quan trọng

  • Higher bandwidth than the lower-speed family alternatives (vsTLV2702ID)
  • Approximately 9% higher bandwidth than the TLV2462ID (vsTLV2462ID)
  • Matches the identified 11 MHz, 800 uA-per-channel class (vsTLV9062ID)

Ghi chú thiết kế

Do not leave either operational-amplifier input floating. Tie the unused channel's inputs to a defined common-mode reference, preferably through the feedback arrangement appropriate for a stable unity-gain buffer. Verify that the reference remains within the TLV2622ID input common-mode range at every supply voltage. Also observe the 2.7 V to 5.5 V supply limits and do not treat the 5.5 V rating as a transient overvoltage allowance.

Place the supply bypass capacitor directly between the V+ and V- pins, with the shortest practical ground return. Keep the SOIC footprint on the same ground plane as the analog source and destination when possible. Route feedback components close to the relevant amplifier inputs and outputs to minimize parasitic capacitance in high-gain or fast-feedback nodes. A dedicated analog ground region may be appropriate, but avoid introducing return current through sensitive input nodes.

The 11 MHz gain-bandwidth product provides bandwidth headroom, but settling time and stability depend on closed-loop gain, noise gain, output loading, and feedback topology. Add an isolation resistor between the TLV2622ID output and a capacitive load when the manufacturer stability guidance calls for it. For ADC interfaces, calculate the required settling interval and verify it against the converter's acquisition time rather than relying only on the nominal gain-bandwidth figure.

Estimated: each channel contributes approximately 800 uA of supply current, so the dual device can draw approximately 1.6 mA before load current and bias-current effects. At a 3.3 V supply, this corresponds to approximately 5.28 mW of internal supply power using I = 800 uA per channel and V = 3.3 V. This estimate is not a substitute for the maximum supply-current specification and should be checked against the actual operating mode and manufacturer limits.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The reviewed manufacturer product page identifies the TLV2622 as an active dual operational amplifier but does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements for the TLV2622ID ordering code. Confirm these attributes in the current manufacturer product and quality documentation.

Dữ liệu được xác minh vào: 2026-11-15 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

TLV2622ID datasheet TLV2622ID pinout TLV2622ID datasheet pdf TLV2622ID equivalent TLV2622ID replacement TLV2622ID vs TLV9062ID TLV2622ID footprint TLV2622ID application circuit Texas Instruments TLV2622ID TLV2622ID price TLV2622ID stock TLV2622 11MHz dual op amp TLV2622ID 800 uA channel TLV2622ID SOIC-8 pinout

Các bộ phận và thuật ngữ liên quan

Texas Instruments TLV2622 TLV2622ID TLV2623ID TLV2462ID TLV2772ID TLV2702ID TLV9062ID operational amplifier dual amplifier rail-to-rail input rail-to-rail output RRO CMOS operational amplifier low-power amplifier analog IC mixed-signal semiconductor gain-bandwidth product supply current per channel common-mode voltage 2.7 V minimum supply 5.5 V maximum supply 11 MHz bandwidth 8-pin SOIC SOIC family surface-mount package sensor conditioning ADC signal conditioning active filter
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ