TLV2762ID - Dual 1.8V 500kHz RRIO Op Amp | Texas Instruments
MPN: TLV2762ID ✓ AktifTLV2762ID Genel Bakış
An operational amplifier is a voltage-amplifying building block that uses high open-loop gain to control an output over a wide input range. Rail-to-rail input amplifiers accept signals close to the positive and negative supply rails, while rail-to-rail outputs can swing close to those limits under typical load conditions. Within the amplifier hierarchy, the TLV2762 belongs to the micropower operational-amplifier family and provides two amplifiers in one package for space-constrained designs.
Key features include a 1.8 V minimum operating supply, 500 kHz bandwidth, approximately 20 microampere quiescent current, and rail-to-rail input and output capability. The low quiescent current limits the supply current drawn when both amplifiers operate continuously, making the device appropriate for portable equipment that spends significant time monitoring low-frequency sensor signals rather than processing high-bandwidth waveforms.
The TLV2762ID combines a speed-versus-power balance that is useful in general-purpose signal chains. A 500 kHz gain-bandwidth product supports moderate closed-loop gains while retaining a compact, low-power implementation. Because the device operates from a single positive supply down to 1.8 V, it can be powered directly from low-energy systems without a negative rail. Designers should still check input and output common-mode limits, capacitive-load stability, output-current capability, and the exact operating limits in the manufacturer datasheet before fixing the circuit.
Typical uses include low-voltage sensor amplifiers, portable measurement systems, current-sense signal conditioning, audio preamplification, and interface buffering. The 8-pin SOIC outline also supports standard surface-mount assembly and hand-soldering workflows. In designs where output noise or channel matching is more important than bandwidth, an application-specific dual amplifier with integrated filtering may provide a better system fit.
A practical design rule is to keep input, feedback, and decoupling connections short, then verify stability with the actual source impedance and load capacitance. Place the supply-bypass capacitor close to the positive rail pin and route the ground return directly to the device ground pin. If the amplifier drives a long cable, ADC input, or capacitive load, add an isolation resistor close to the output and confirm settling behavior with oscilloscope measurements.
This page combines the manufacturer product information, distributor listings, pin-level guidance, drop-in alternatives, and application-focused design notes to support faster component selection and PCB planning.
Drop-in alternatifler için TLV2762ID — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller TLV2762ID (aynı form faktörü ve ayağa oturma) — farklı olan Operating Temperature Range, Package, Gain-Bandwidth Product, Input Bias Current, Maximum Supply Voltage.
TLV271IDR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →TLV2762UIP
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
TLV2762UID
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
TLV2762ID Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Minimum Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 500 kHz |
| Durağan Akım | Approximately 20 microampere per amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Supply Type | Single supply |
| Paket | 8-pin SOIC, 0.154 inch (3.90 mm) wide |
| Montaj Türü | Surface mount |
| İşletim Sıcaklığı Aralığı | Industrial temperature range |
TLV2762ID Pin Yapısı
| Pin 1 | OUTA — Channel A output |
| Pin 2 | INA- — Channel A inverting input |
| Pin 3 | INA+ — Channel A non-inverting input |
| Pin 4 | V+ — Positive supply voltage |
| Pin 5 | INB+ — Channel B non-inverting input |
| Pin 6 | INB- — Channel B inverting input |
| Pin 7 | OUTB — Channel B output |
| Pin 8 | V- — Negative supply or ground connection |
Tipik Uygulamalar
TLV2762ID için uygundur 6 uygulamas: Battery-Powered Sensor Conditioning, Portable Instrumentation Signal Conditioning, Low-Voltage Current-Sense Amplification, Audio Preamplifier and Interface Buffer, Single-Supply ADC Interface, Industrial Control and Automation I/O.
Battery-Powered Sensor Conditioning
The TLV2762ID fits low-energy sensor front ends because it operates from 1.8 V and consumes approximately 20 microampere per amplifier. One channel can amplify a resistive sensor bridge or thermistor signal while the other performs filtering or level conditioning before an ADC. Rail-to-rail inputs help preserve signal headroom near the supply rails, and the 500 kHz gain-bandwidth product supports moderate closed-loop gains. Check input bias current against the sensor impedance to prevent gain errors, and place the bypass capacitor close to pin 4.
Önerilen
Portable Instrumentation Signal Conditioning
The TLV2762ID is appropriate for compact handheld instruments that combine analog measurement with low-voltage digital processing. Its dual architecture supports two independent gain or buffer stages without requiring two packages, while the 8-pin SOIC footprint simplifies surface-mount assembly. The 1.8 V minimum supply and approximately 20 microampere quiescent current per amplifier support energy-limited operation, and 500 kHz bandwidth accommodates many low-frequency pressure, flow, or position sensors. Validate noise performance against the required measurement resolution.
Önerilen
Low-Voltage Current-Sense Amplification
The TLV2762ID can amplify the small voltage generated across a low-value shunt resistor in a 1.8 V supply system. Rail-to-rail input capability preserves common-mode range when the shunt signal lies close to the positive rail, and the 500 kHz gain-bandwidth product supports higher-bandwidth current control than a purely micropower slow amplifier. Keep the Kelvin sense connections short and symmetrical, and verify amplifier input offset against the smallest current level that must be resolved.
Önerilen
Audio Preamplifier and Interface Buffer
The TLV2762ID can serve as a low-voltage audio preamplifier or impedance buffer in portable headphones, microphones, and small speakers. Its dual-channel configuration allows a stereo pair of signals to be processed in one package, and rail-to-rail output capability improves voltage utilization at 1.8 V to 3.6 V. The 500 kHz bandwidth covers audio-band signals, although system noise, input bias current, and load stability determine practical performance. Add series isolation resistance when driving capacitive inputs.
Önerilen
Single-Supply ADC Interface
The TLV2762ID is useful as a rail-to-rail buffer between analog sensors and a low-voltage ADC input. Buffering prevents the sensor source impedance from degrading ADC acquisition time, while the dual package can handle two channels or combine an active filter with a driver. Operation from 1.8 V to 3.6 V allows direct interfacing with modern low-power converters and ADCs. Confirm ADC input range, acquisition requirements, and capacitive loading before finalizing the external filter and isolation resistance.
Önerilen
Industrial Control and Automation I/O
The TLV2762ID can condition low-level analog control signals in compact industrial automation modules powered from low-voltage rails. Rail-to-rail inputs help handle sensor outputs near the supply limits, while 500 kHz bandwidth is sufficient for many slow feedback loops and monitoring channels. The approximately 20 microampere quiescent current per amplifier reduces the penalty of continuous analog monitoring. Confirm the industrial temperature range, EMC requirements, and isolation strategy against the enclosure and cable environment.
Önerilen
Mühendislik referans verileri: TLV2762ID — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Consider the TLV271IDR when its lower-power or offset-voltage characteristics provide a better match, but verify the bandwidth and quiescent-current changes against the original design. The TLV2762UIP and TLV2762UID offer the same core TLV2762 amplifier performance in an 8-pin SOIC outline when their specific ordering and packing formats fit the assembly process. For all candidates, check common-mode range, output swing, noise, input bias current, capacitive-load stability, and temperature-range requirements before approving a substitution.
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | TLV271IDR | TLV2762UIP | TLV2762UID |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint | 8-pin SOIC - same footprint |
| Amplifier Configuration | Dual | Dual | Dual | Dual |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
Ana Farklılayıcılar
- 500 kHz speed within a micropower dual amplifier (karşılaştırma:TLV271IDR)
- Dual low-power rail-to-rail signal conditioning in one package (karşılaştırma:TLV271IDR)
- Single-supply operation down to 1.8 V (karşılaştırma:TLV2762UIP)
Tasarım Notları
Place the supply-bypass capacitor immediately beside pin 4, and connect pin 8 to the ground plane with a short, low-impedance return path. Keep the two non-inverting inputs, the two inverting inputs, and their feedback components away from switching nodes and motor-current paths. Because the TLV2762ID is a 500 kHz micropower amplifier, long PCB traces can add parasitic capacitance and reduce stability margin.
When driving an ADC, cable, or other capacitive load, place a small isolation resistor directly at the amplifier output and keep the feedback connection close to the device. Increase resistance only as needed to preserve settling time, and confirm the output does not oscillate under the worst-case cable capacitance. Verify the signal against the full common-mode and output-swing ranges at the lowest intended supply voltage.
Do not treat rail-to-rail input as an unlimited input range, and do not assume the output can reach either supply rail under every load. The TLV2762ID also operates as a single-supply device, so pin 8 is normally tied to ground. Check input bias current against high-impedance sensors, input offset against the smallest signal of interest, and output-current demand against the intended load before releasing the layout.
Uyumluluk Bilgisi
The TLV2762 is an industrial-temperature-range general-purpose operational amplifier. RoHS, REACH, lead-free, and halogen-free status require confirmation from the current manufacturer product documentation or declaration.