Cirrus Logic Inc.

WM8962BECSN/R - Stereo 24-Bit Audio Codec | Cirrus Logic

MPN: WM8962BECSN/R ✓ Aktif
1.7 V to 2.0 V Vdss 49-CSP Package
MOQ: 1 |

WM8962BECSN/R Genel Bakış

Cirrus Logic WM8962BECSN/R is a low-power stereo audio codec with 24-bit resolution, I2C and SPI control interfaces, and a 49-ball CSP package measuring 3.6 mm by 3.9 mm. It operates from a 1.7 V to 2.0 V supply and supports sampling rates from 8 kHz to 96 kHz, making it suitable for compact embedded audio systems.

An audio codec is an interface IC that converts digital audio data into an analog output and converts analog microphone signals into digital PCM data. Within the semiconductor hierarchy, a stereo codec belongs to an audio interface IC, which is part of the broader integrated-circuit category. It is typically paired with an application processor, DSP, amplifier, microphone, speaker, and digital control interface.

The WM8962B architecture integrates an ADC and stereo DAC for 24-bit audio processing. Its control interface supports I2C and SPI, allowing firmware to configure registers, mixer paths, and audio playback. The manufacturer product page also identifies an integrated charge pump, a dual-mode charge-pump architecture, and a DC servo. These features support ground-referenced headphone outputs and reduce the need for output DC-blocking capacitors.

Integrated stereo Class-D speaker drive, microphone support, and audio-enhancement DSP expand the codec beyond basic signal conversion. The 24-bit processing path supports the full 8 kHz to 96 kHz sampling range, while the 1.7 V to 2.0 V analog supply range targets compact portable equipment. The manufacturer lists an operating temperature range of -40 °C to +85 °C for the exact ordered device.

Typical uses include portable media players, mobile multimedia equipment, connected audio products, voice-capture terminals, and compact consumer appliances. Its small CSP footprint is useful where board area is constrained, while integrated headphone and speaker functions can reduce the number of external audio components. Firmware must still verify clocking, filter configuration, mixer routing, and output settings through the I2C or SPI interface.

Layout should keep analog supply, ground, microphone, and headphone paths short, with suitable decoupling placed close to the device pins. Digital control traces should remain separated from sensitive analog nodes. The integrated charge pump and DC servo simplify headphone output topology, but external filtering, clock planning, and signal-integrity checks remain essential for low-noise performance.

This product page combines the exact ordering information, operating limits, digital interfaces, package data, functional architecture, sourcing path, and engineering guidance for the WM8962BECSN/R. It also distinguishes the exact orderable suffix from the broader WM8962B family designation and identifies where additional board-level design work is required.

Drop-in alternatifler için WM8962BECSN/R — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller WM8962BECSN/R (aynı form faktörü ve ayağa oturma) — farklı olan Package Dimensions, Package Type.

Cirrus Logic Inc.
Package Dimensions: 3.59 mm x 3.98 mm
Package Type: 49-WLCSP

Bu ürüne yer değiştirme seçenekleri mevcut değil.

Alternatifleri Talep Edin

WM8962BECSN/R Maksimum Değerlendirmeler & Elektriksel Özellikler

Device Type Stereo audio codec
Audio Resolution 24 bit
Digital Control Interfaces I2C and SPI
Analog Supply Voltage 1.7 V to 2.0 V
Sampling Rate Range 8 kHz to 96 kHz
İşletim Sıcaklığı Aralığı -40 °C to +85 °C
Package Type 49-CSP
Package Dimensions 3.6 mm × 3.9 mm
Signal Conversion 24-bit encoder and decoder
Headphone Output Architecture Integrated charge pump with ground-referenced output
Charge Pump Architecture Dual-mode charge pump
DC Offset Control Integrated DC servo
Speaker Output Integrated stereo Class-D speaker drive
Audio Processing Integrated audio enhancement
Microphone Support Integrated analog microphone input
RoHS Compliance Compliant
Moisture Sensitivity Level MSL1
Montaj Türü Surface mount

WM8962BECSN/R 3.6 mm × 3.9 mm Pin Yapısı Kılavuzu

WM8962BECSN/R (3.6 mm × 3.9 mm paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.

3.6 mm × 3.9 mm paket pin çizelgesi için WM8962BECSN/R

Ayrıntılı pin çıkış verisi mevcut değil: WM8962BECSN/R.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

WM8962BECSN/R için uygundur 6 uygulamas: Portable Media Player, Mobile Multimedia Terminal, Connected Audio Product, Voice-Capture Terminal, Compact Speaker Amplification, Industrial Audio Control Panel.

📱

Portable Media Player

The WM8962BECSN/R fits portable media players that require high-resolution playback in a compact board area. Its 24-bit encoder and decoder support sampling from 8 kHz to 96 kHz, while the 1.7 V to 2.0 V supply range aligns with compact embedded power systems. The 49-CSP package measures 3.6 mm by 3.9 mm, preserving board space around the processor. Its integrated charge pump provides a ground-referenced headphone output, and the DC servo reduces output offset. Firmware can configure playback and mixer behavior through either I2C or SPI, allowing the host controller to select the interface that best fits its bus architecture.

📱

Mobile Multimedia Terminal

The WM8962BECSN/R is appropriate for mobile multimedia terminals combining digital media playback, voice capture, and integrated speaker output. The codec supports 24-bit signal processing over an 8 kHz to 96 kHz sampling range, and its I2C and SPI interfaces simplify connection to embedded application processors. Integrated microphone support reduces the external analog path, while stereo Class-D drive can support efficient speaker operation. The 3.6 mm by 3.9 mm CSP footprint is valuable in compact enclosures, although layout must preserve quiet analog grounding and short return paths around the microphone and headphone sections.

🌐

Connected Audio Product

The WM8962BECSN/R can support connected audio products that combine local playback, voice input, and compact speaker output. Its dual digital control options, I2C and SPI, provide flexibility for host processors with different peripheral resources, while the 24-bit conversion path supports high-fidelity source material up to 96 kHz. The integrated charge-pump architecture removes conventional headphone DC-blocking capacitors, and the DC servo helps control output ground offset. Designers should still budget board area for required external capacitors, clock components, filtering, and any output network dictated by the selected impedance and power level.

🎙️

Voice-Capture Terminal

The WM8962BECSN/R is suitable for compact voice-capture terminals requiring microphone conversion and headphone monitoring in one device. Its integrated ADC and stereo DAC operate at 24-bit resolution across an 8 kHz to 96 kHz sampling range, allowing software to select narrower-band voice modes or higher-quality capture paths. I2C and SPI register access simplifies integration with embedded controllers, and the compact 49-CSP package reduces footprint. The microphone bias, analog filtering, clock source, and grounding should be designed from the manufacturer application guidance to prevent switching or digital-bus noise from appearing in the captured signal.

🔊

Compact Speaker Amplification

The WM8962BECSN/R suits compact products that need integrated stereo Class-D speaker drive rather than a separate codec-to-amplifier signal chain. The codec supports 24-bit processing up to 96 kHz and operates from a 1.7 V to 2.0 V supply, while the integrated charge pump and DC servo simplify the headphone and signal-output architecture. Using the integrated speaker function can reduce board area, but the application still requires correct output filtering, stable supplies, adequate layout separation, and thermal consideration at sustained high playback levels. Firmware should configure the mixer and output path to prevent clipping before the Class-D stage.

🏭

Industrial Audio Control Panel

The WM8962BECSN/R can serve as the audio interface in compact industrial controls that provide local playback, audible feedback, or voice input. Its -40 °C to +85 °C operating range supports a broad range of industrial environments, while the 49-CSP package limits board consumption. The 24-bit codec path and configurable 8 kHz to 96 kHz sampling allow the same design to handle high-rate media or lower-rate communication audio. Firmware-controlled I2C or SPI configuration supports event-driven audio control, while careful partitioning of analog and digital returns helps isolate the microphone and headphone paths from switching converters and control-bus activity.

Önerilen Ürünler Özeti

WM8962BECSN/R Cirrus Logic Inc. Kullanıldığı Yer: Portable Media Player, Mobile Multimedia Terminal, Connected Audio Product, Voice-Capture Terminal, Compact Speaker Amplification, Industrial Audio Control Panel WM8962B Related codec family with integrated charge pump Kullanıldığı Yer: Portable Media Player, Mobile Multimedia Terminal, Connected Audio Product, Voice-Capture Terminal, Compact Speaker Amplification, Industrial Audio Control Panel
What is the WM8962BECSN/R?
The WM8962BECSN/R is a Cirrus Logic low-power stereo audio codec with 24-bit conversion, I2C and SPI control, and integrated headphone and speaker functions. According to the Cirrus Logic WM8962B product page, it uses an integrated charge pump to create a ground-referenced headphone output, while a DC servo reduces output offset. The device is packaged in a 49-CSP measuring 3.6 mm by 3.9 mm.
What are the key specifications of WM8962BECSN/R that engineers should know?
The WM8962BECSN/R provides 24-bit encoder and decoder functions, 8 kHz to 96 kHz sampling, I2C and SPI control, and a 1.7 V to 2.0 V supply range. According to the Cirrus Logic WM8962B product page, the codec also integrates a dual-mode charge pump, a DC servo, microphone support, audio enhancement, and stereo Class-D speaker drive in a 49-CSP package.
Where can I download the WM8962BECSN/R datasheet PDF?
The manufacturer product page for the WM8962B family is the appropriate starting point for the WM8962BECSN/R technical documentation. The exact device is identified as a 24-bit stereo codec with I2C and SPI interfaces in a 49-CSP package. Use the pin-description and register tables in the manufacturer datasheet when assigning PCB tracks and writing control firmware.
Where can I find the WM8962BECSN/R pinout?
The WM8962BECSN/R pinout must be taken from the manufacturer datasheet because its 49-CSP land pattern does not correspond to a common 48-pin or 64-pin library package. The device uses a 49-CSP package measuring 3.6 mm by 3.9 mm. Use the package drawing and ball-assignment table for PCB footprint creation, exposed-area handling, and assembly design.
What is the operating voltage of the WM8962BECSN/R?
The WM8962BECSN/R operates from a 1.7 V to 2.0 V analog supply. According to the Cirrus Logic WM8962B product page and the exact-device technical listing, the codec supports 8 kHz to 96 kHz sampling and is specified from -40 °C to +85 °C. The power design must also account for any separate digital supply and I/O voltage requirements defined in the manufacturer datasheet.
Does the WM8962BECSN/R need DC-blocking capacitors on its headphone output?
The WM8962BECSN/R does not require conventional DC-blocking capacitors for its ground-referenced headphone output under the intended operating configuration. According to the Cirrus Logic WM8962B product page, the integrated charge pump removes the need for these capacitors, and the DC servo reduces ground-offset effects. Output resistance, load conditions, and startup behavior should still be checked in the system design.
WM8962BECSN/R vs WM8962B - what is the difference?
WM8962BECSN/R is the exact orderable device designation, while WM8962B is the broader Cirrus Logic family and product-page designation. The exact part is specified as a 24-bit stereo codec with I2C and SPI in a 49-CSP package measuring 3.6 mm by 3.9 mm. The family architecture includes an integrated charge pump, DC servo, audio enhancement, and Class-D speaker drive.
When should I choose WM8962BECSN/R instead of a generic stereo codec?
Choose the WM8962BECSN/R when a compact design needs 24-bit conversion, 8 kHz to 96 kHz sampling, and both I2C and SPI control in a 3.6 mm by 3.9 mm CSP footprint. Its integrated charge pump, DC servo, microphone support, and stereo Class-D drive can reduce external circuitry. A generic codec may be preferable only when its pinout and electrical requirements better match an existing design.
Is the WM8962BECSN/R suitable for portable audio and mobile multimedia devices?
The WM8962BECSN/R is suitable for compact portable audio and mobile multimedia equipment because it combines a 24-bit stereo codec, 1.7 V to 2.0 V operation, and a small 49-CSP package. According to the Cirrus Logic WM8962B product page, its integrated charge pump and DC servo simplify headphone output design, while Class-D speaker drive supports efficient connected-audio products.
What is the best drop-in replacement for WM8962BECSN/R?
A drop-in replacement should preserve the 49-CSP footprint, all ball assignments, I2C and SPI interface, 24-bit conversion, 1.7 V to 2.0 V supply operation, and 8 kHz to 96 kHz sampling support. No pin-compatible substitute was confirmed for the exact WM8962BECSN/R ordering code. The broader WM8962B family is a related device family, but a specific package suffix must be verified before treating it as a replacement.
Can WM8962B replace WM8962BECSN/R?
WM8962B identifies the broader Cirrus Logic product family, not a verified alternate package suffix for the WM8962BECSN/R. The family page confirms the shared charge-pump, DC-servo, and low-power codec architecture, but it does not establish that every WM8962B ordering option has the same 49-ball footprint. Confirm the exact suffix, ball map, electrical limits, and register compatibility before using it as a drop-in replacement.
Where to buy WM8962BECSN/R online?
Use the Request a Quote form on this page to request WM8962BECSN/R availability, authorized sourcing support, and current delivery information for the exact ordering code. The part is identified by Cirrus Logic as a 24-bit stereo audio codec in a 49-CSP package. Submit the manufacturer suffix WM8962BECSN/R and the required package quantity so the request is matched to the correct device.
What is the price of WM8962BECSN/R?
Current WM8962BECSN/R pricing is obtained through the Request a Quote form on this page rather than through a static quotation. Provide the exact MPN, required quantity, and shipment destination for a current sourcing response. The price can vary with quantity, package format, authorization, and market conditions, so a historical listing should not be treated as a firm quotation.
What is the lead time and stock status for WM8962BECSN/R?
Request current stock status, lead time, and minimum order quantity through the Request a Quote form on this page. The device is distributed as the exact Cirrus Logic WM8962BECSN/R ordering code, but stock and production timing can change. Include your required quantity, target date, and packaging preference in the request to obtain an actionable supply response.
Is WM8962BECSN/R RoHS compliant?
The WM8962BECSN/R is identified as RoHS compliant in the exact-device technical listing. Its operating range is -40 °C to +85 °C, and the associated component record lists MSL1 moisture sensitivity. RoHS status should be confirmed against the current manufacturer declaration for the exact ordering code before final production release, particularly when new material declarations are required.

Mühendislik referans verileri: WM8962BECSN/R — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose WM8962BECSN/R when a compact product needs 24-bit stereo conversion, flexible I2C or SPI control, microphone support, a ground-referenced headphone output, and integrated Class-D speaker drive. The 1.7 V to 2.0 V supply range and 49-CSP footprint are particularly useful for portable and embedded audio systems. Confirm the exact package drawing, clock configuration, external capacitor requirements, and output power before layout release. WM8962B identifies the related family architecture, but it should not be treated as a drop-in replacement unless a specific ordering option is proven to have the same ball map and electrical behavior. A different codec should be selected only when the required converter resolution, interface, speaker-drive capability, package, or lifecycle requirements cannot be met.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün
Brand Cirrus Logic
Package 49-CSP (3.6 mm × 3.9 mm)
Audio Resolution 24 bit
Control Interface I2C and SPI
Supply Voltage 1.7 V to 2.0 V
Sampling Rate 8 kHz to 96 kHz
Operating Temperature -40 °C to +85 °C
Headphone Output Integrated charge pump and DC servo
Speaker Output Integrated stereo Class-D drive
RoHS Status Compliant

Ana Farklılayıcılar

  • Integrated ground-referenced headphone output (karşılaştırma:WM8962B)
  • Compact mixed-signal integration (karşılaştırma:WM8962B)
  • Broad sampling-rate control (karşılaştırma:WM8962B)

Tasarım Notları

Create the footprint from the manufacturer package drawing rather than treating the WM8962BECSN/R as a generic 48-ball CSP. Its 49-CSP package measures 3.6 mm by 3.9 mm, so ball count, pitch, and orientation must be verified against the exact land pattern. Keep microphone inputs, headphone outputs, analog supplies, and their return paths compact. Place required bypass capacitors at the associated supply pins and provide a low-impedance ground reference for the analog section.

Separate I2C and SPI control routing from the microphone and headphone paths to reduce digital coupling into the 24-bit audio signal. Use a continuous ground reference under the codec where the layout rules permit it, and route high-current Class-D and charge-pump returns without sharing narrow paths with sensitive microphone nodes. Validate the final layout with crosstalk measurements because the small CSP footprint can make return-path segmentation difficult.

Design the 1.7 V to 2.0 V analog supply with low ripple and adequate transient response. Place the required input and output capacitors close to their associated pins, and check startup sequencing, load current, voltage droop, and the power consumed by the Class-D output stage. The manufacturer application guidance should determine the capacitor values and power-source requirements; changing them without checking startup and stability behavior can produce audible faults.

Do not treat WM8962B as a confirmed drop-in substitute for every WM8962BECSN/R package option. The family page confirms the shared codec architecture, but a replacement must match the 49-ball footprint, pin assignments, electrical limits, and register behavior. Also verify the clock source, sampling mode, filter configuration, and microphone-bias arrangement through the device control interface before enabling full-scale capture or playback.

Uyumluluk Bilgisi

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

RoHS compliance is identified for the exact device. The associated component record lists MSL1. Automotive qualification, REACH status, lead-free status, halogen-free status, and conflict-minerals status are not stated for this part.

Veri doğrulanma tarihi: 2026-11-16 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

WM8962BECSN/R datasheet WM8962BECSN/R pinout WM8962BECSN/R datasheet pdf WM8962BECSN/R specifications WM8962BECSN/R price WM8962BECSN/R stock WM8962BECSN/R equivalent WM8962BECSN/R replacement WM8962BECSN/R vs WM8962B WM8962B stereo codec 49-CSP stereo audio codec 24-bit I2C SPI audio codec

İlgili Bileşenler ve Terimler

Cirrus Logic WM8962BECSN/R WM8962B stereo audio codec audio codec audio interface IC integrated circuit semiconductor 24-bit ADC 24-bit DAC I2C SPI ground-referenced headphone output integrated charge pump dual-mode charge pump DC servo stereo Class-D speaker drive audio enhancement DSP microphone input 49-CSP package surface mount RoHS MSL1 portable audio mobile multimedia
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle