WM8962BECSN/R - Stereo 24-Bit Audio Codec | Cirrus Logic
料号: WM8962BECSN/R ✓ 量产中WM8962BECSN/R 概述
An audio codec is an interface IC that converts digital audio data into an analog output and converts analog microphone signals into digital PCM data. Within the semiconductor hierarchy, a stereo codec belongs to an audio interface IC, which is part of the broader integrated-circuit category. It is typically paired with an application processor, DSP, amplifier, microphone, speaker, and digital control interface.
The WM8962B architecture integrates an ADC and stereo DAC for 24-bit audio processing. Its control interface supports I2C and SPI, allowing firmware to configure registers, mixer paths, and audio playback. The manufacturer product page also identifies an integrated charge pump, a dual-mode charge-pump architecture, and a DC servo. These features support ground-referenced headphone outputs and reduce the need for output DC-blocking capacitors.
Integrated stereo Class-D speaker drive, microphone support, and audio-enhancement DSP expand the codec beyond basic signal conversion. The 24-bit processing path supports the full 8 kHz to 96 kHz sampling range, while the 1.7 V to 2.0 V analog supply range targets compact portable equipment. The manufacturer lists an operating temperature range of -40 °C to +85 °C for the exact ordered device.
Typical uses include portable media players, mobile multimedia equipment, connected audio products, voice-capture terminals, and compact consumer appliances. Its small CSP footprint is useful where board area is constrained, while integrated headphone and speaker functions can reduce the number of external audio components. Firmware must still verify clocking, filter configuration, mixer routing, and output settings through the I2C or SPI interface.
Layout should keep analog supply, ground, microphone, and headphone paths short, with suitable decoupling placed close to the device pins. Digital control traces should remain separated from sensitive analog nodes. The integrated charge pump and DC servo simplify headphone output topology, but external filtering, clock planning, and signal-integrity checks remain essential for low-noise performance.
This product page combines the exact ordering information, operating limits, digital interfaces, package data, functional architecture, sourcing path, and engineering guidance for the WM8962BECSN/R. It also distinguishes the exact orderable suffix from the broader WM8962B family designation and identifies where additional board-level design work is required.
直接替换替代料: WM8962BECSN/R ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: WM8962BECSN/R (相同外形与封装尺寸) ——差异在于 Package Dimensions, Package Type.
该产品暂无直接替换替代料。
请求替代料WM8962BECSN/R 最大额定值与电气特性
| Device Type | Stereo audio codec |
| Audio Resolution | 24 bit |
| Digital Control Interfaces | I2C and SPI |
| Analog Supply Voltage | 1.7 V to 2.0 V |
| Sampling Rate Range | 8 kHz to 96 kHz |
| 工作温度范围 | -40 °C to +85 °C |
| Package Type | 49-CSP |
| Package Dimensions | 3.6 mm × 3.9 mm |
| Signal Conversion | 24-bit encoder and decoder |
| Headphone Output Architecture | Integrated charge pump with ground-referenced output |
| Charge Pump Architecture | Dual-mode charge pump |
| DC Offset Control | Integrated DC servo |
| Speaker Output | Integrated stereo Class-D speaker drive |
| Audio Processing | Integrated audio enhancement |
| Microphone Support | Integrated analog microphone input |
| RoHS Compliance | Compliant |
| Moisture Sensitivity Level | MSL1 |
| 安装类型 | Surface mount |
WM8962BECSN/R 3.6 mm × 3.9 mm 引脚配置指南
WM8962BECSN/R(3.6 mm × 3.9 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: WM8962BECSN/R.
请参阅 数据手册 以查看完整引脚配置。
典型应用
WM8962BECSN/R 适用于 6 应用s: Portable Media Player, Mobile Multimedia Terminal, Connected Audio Product, Voice-Capture Terminal, Compact Speaker Amplification, Industrial Audio Control Panel.
Portable Media Player
The WM8962BECSN/R fits portable media players that require high-resolution playback in a compact board area. Its 24-bit encoder and decoder support sampling from 8 kHz to 96 kHz, while the 1.7 V to 2.0 V supply range aligns with compact embedded power systems. The 49-CSP package measures 3.6 mm by 3.9 mm, preserving board space around the processor. Its integrated charge pump provides a ground-referenced headphone output, and the DC servo reduces output offset. Firmware can configure playback and mixer behavior through either I2C or SPI, allowing the host controller to select the interface that best fits its bus architecture.
推荐
Mobile Multimedia Terminal
The WM8962BECSN/R is appropriate for mobile multimedia terminals combining digital media playback, voice capture, and integrated speaker output. The codec supports 24-bit signal processing over an 8 kHz to 96 kHz sampling range, and its I2C and SPI interfaces simplify connection to embedded application processors. Integrated microphone support reduces the external analog path, while stereo Class-D drive can support efficient speaker operation. The 3.6 mm by 3.9 mm CSP footprint is valuable in compact enclosures, although layout must preserve quiet analog grounding and short return paths around the microphone and headphone sections.
推荐
Connected Audio Product
The WM8962BECSN/R can support connected audio products that combine local playback, voice input, and compact speaker output. Its dual digital control options, I2C and SPI, provide flexibility for host processors with different peripheral resources, while the 24-bit conversion path supports high-fidelity source material up to 96 kHz. The integrated charge-pump architecture removes conventional headphone DC-blocking capacitors, and the DC servo helps control output ground offset. Designers should still budget board area for required external capacitors, clock components, filtering, and any output network dictated by the selected impedance and power level.
推荐
Voice-Capture Terminal
The WM8962BECSN/R is suitable for compact voice-capture terminals requiring microphone conversion and headphone monitoring in one device. Its integrated ADC and stereo DAC operate at 24-bit resolution across an 8 kHz to 96 kHz sampling range, allowing software to select narrower-band voice modes or higher-quality capture paths. I2C and SPI register access simplifies integration with embedded controllers, and the compact 49-CSP package reduces footprint. The microphone bias, analog filtering, clock source, and grounding should be designed from the manufacturer application guidance to prevent switching or digital-bus noise from appearing in the captured signal.
推荐
Compact Speaker Amplification
The WM8962BECSN/R suits compact products that need integrated stereo Class-D speaker drive rather than a separate codec-to-amplifier signal chain. The codec supports 24-bit processing up to 96 kHz and operates from a 1.7 V to 2.0 V supply, while the integrated charge pump and DC servo simplify the headphone and signal-output architecture. Using the integrated speaker function can reduce board area, but the application still requires correct output filtering, stable supplies, adequate layout separation, and thermal consideration at sustained high playback levels. Firmware should configure the mixer and output path to prevent clipping before the Class-D stage.
推荐
Industrial Audio Control Panel
The WM8962BECSN/R can serve as the audio interface in compact industrial controls that provide local playback, audible feedback, or voice input. Its -40 °C to +85 °C operating range supports a broad range of industrial environments, while the 49-CSP package limits board consumption. The 24-bit codec path and configurable 8 kHz to 96 kHz sampling allow the same design to handle high-rate media or lower-rate communication audio. Firmware-controlled I2C or SPI configuration supports event-driven audio control, while careful partitioning of analog and digital returns helps isolate the microphone and headphone paths from switching converters and control-bus activity.
推荐
推荐产品汇总
工程参考数据: WM8962BECSN/R ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | Cirrus Logic |
| Package | 49-CSP (3.6 mm × 3.9 mm) |
| Audio Resolution | 24 bit |
| Control Interface | I2C and SPI |
| Supply Voltage | 1.7 V to 2.0 V |
| Sampling Rate | 8 kHz to 96 kHz |
| Operating Temperature | -40 °C to +85 °C |
| Headphone Output | Integrated charge pump and DC servo |
| Speaker Output | Integrated stereo Class-D drive |
| RoHS Status | Compliant |
关键差异点
- Integrated ground-referenced headphone output (对比 WM8962B)
- Compact mixed-signal integration (对比 WM8962B)
- Broad sampling-rate control (对比 WM8962B)
设计说明
Create the footprint from the manufacturer package drawing rather than treating the WM8962BECSN/R as a generic 48-ball CSP. Its 49-CSP package measures 3.6 mm by 3.9 mm, so ball count, pitch, and orientation must be verified against the exact land pattern. Keep microphone inputs, headphone outputs, analog supplies, and their return paths compact. Place required bypass capacitors at the associated supply pins and provide a low-impedance ground reference for the analog section.
Separate I2C and SPI control routing from the microphone and headphone paths to reduce digital coupling into the 24-bit audio signal. Use a continuous ground reference under the codec where the layout rules permit it, and route high-current Class-D and charge-pump returns without sharing narrow paths with sensitive microphone nodes. Validate the final layout with crosstalk measurements because the small CSP footprint can make return-path segmentation difficult.
Design the 1.7 V to 2.0 V analog supply with low ripple and adequate transient response. Place the required input and output capacitors close to their associated pins, and check startup sequencing, load current, voltage droop, and the power consumed by the Class-D output stage. The manufacturer application guidance should determine the capacitor values and power-source requirements; changing them without checking startup and stability behavior can produce audible faults.
Do not treat WM8962B as a confirmed drop-in substitute for every WM8962BECSN/R package option. The family page confirms the shared codec architecture, but a replacement must match the 49-ball footprint, pin assignments, electrical limits, and register behavior. Also verify the clock source, sampling mode, filter configuration, and microphone-bias arrangement through the device control interface before enabling full-scale capture or playback.
合规信息
RoHS compliance is identified for the exact device. The associated component record lists MSL1. Automotive qualification, REACH status, lead-free status, halogen-free status, and conflict-minerals status are not stated for this part.