Z86E2112FSC - 8-Bit 12MHz OTP MCU with UART | Zilog
MPN: Z86E2112FSC ✓ AktifZ86E2112FSC Genel Bakış
An 8-bit microcontroller is an embedded-processing IC that integrates a processor core, nonvolatile program memory, data memory, I/O ports, and communication peripherals into one package. The Z86E2112FSC belongs to the Z8 family, where the MCU sits within the broader hierarchy of embedded controllers, semiconductor devices, and programmable control systems. Its one-time-programmable architecture allows application firmware to be permanently written into the device for production control.
The Z86E2112FSC combines a 12 MHz maximum clock with 8 KB of OTP program memory and a hardware UART. The UART supports communications with host computers, sensors, human-interface modules, and other embedded controllers without requiring a separate serial-interface IC. The 32 I/O pins provide a practical interface capacity for logic inputs, output control, and external peripheral connections when the complete pin-assignment table and electrical limits are followed.
This part operates from a nominal 5.00 V supply with a listed maximum of 5.50 V. That supply range makes a regulated 5 V rail the natural operating environment. Clock-sensitive and UART-connected circuits should use suitable bypassing, controlled rise times, and signal levels compatible with the device's documented electrical characteristics. Because its program memory is OTP rather than reprogrammable Flash, firmware changes require a new programmed device.
Typical uses include compact serial controllers, appliance interfaces, industrial modules, instrumentation, lighting controls, and embedded communication equipment. The 44-pin LQFP package offers enough connections for mixed digital I/O and serial functions while remaining compatible with conventional surface-mount assembly. Designs must observe the manufacturer’s pin and electrical requirements when assigning multiplexing functions.
For a new PCB, the most important design decision is preserving the exact 44-pin footprint and validating the selected oscillator, reset, supply, and UART implementation against the manufacturer datasheet. For an existing assembly, verify package suffix, temperature grade, supply voltage, firmware memory, and all peripheral assignments before considering substitution.
This page combines the device’s core operating specifications with sourcing guidance, drop-in replacement analysis, package considerations, and application-oriented design notes. It is intended to help engineers determine whether the Z86E2112FSC matches the required memory, clock, I/O, serial-interface, supply, and package constraints without overlooking OTP-programming limitations.
Drop-in alternatifler için Z86E2112FSC — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Z86E2112PSC
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
Z86E2112FSC Maksimum Değerlendirmeler & Elektriksel Özellikler
| Processor Architecture | 8-bit Z8 microcontroller |
| Maximum Clock Speed | 12 MHz |
| Program Memory | 8 KB OTP |
| Program Memory Organization | 8K x 8 bits |
| RAM | 236 x 8 bits |
| Number of I/O Pins | 32 pins |
| UART | 1 UART interface |
| Nominal Supply Voltage | 5.00 V |
| Maximum Supply Voltage | 5.50 V |
| Paket | 44-pin LQFP |
| Montaj Türü | Surface mount |
| Core | Z8 embedded processor and controller |
| Bellek Türü | One-time programmable |
| Operating Frequency | Up to 12 MHz |
Z86E2112FSC 44-pin lqfp Pin Yapısı Kılavuzu
Z86E2112FSC (44-pin lqfp paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: Z86E2112FSC.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
Z86E2112FSC için uygundur 6 uygulamas: UART-Based Appliance Controller, Industrial Serial Interface Module, LED Lighting and Sequencer Control, Instrumentation Front-End Control, Smart Sensor Hub, Communications and Network Equipment Control.
UART-Based Appliance Controller
The Z86E2112FSC fits compact appliance-control boards that need a dedicated UART and a moderate number of digital I/O lines. Its 12 MHz Z8 processor provides the operating speed for protocol handling and state-machine logic, while 8 KB of OTP memory stores fixed appliance firmware and 236 bytes of RAM supports short working buffers. Place the device beside a regulated 5 V rail and connect the UART through the pin and electrical network specified in the manufacturer datasheet. Because program memory is OTP, firmware changes require replacement of the programmed MCU, which makes the device most appropriate when production logic is stable and field updates are not needed.
Önerilen
Industrial Serial Interface Module
The Z86E2112FSC is suitable for a compact industrial serial module that translates commands, monitors discrete inputs, and controls outputs through a UART. The 32 I/O pins offer more interface capacity than a minimal 8-pin controller, while the 8 KB OTP program space can hold a dedicated command processor and device-specific logic. The nominal 5.00 V operating voltage and 5.50 V maximum support integration with a regulated industrial rail, subject to the complete operating-temperature requirements. Keep the UART routing away from switching-node circuitry, provide local supply bypassing, and verify every multiplexing assignment against the 44-pin package table before releasing the layout.
Önerilen
LED Lighting and Sequencer Control
The Z86E2112FSC can control LED sequences, status indicators, and simple driver-enable logic in a lighting module. Its 12 MHz clock and 32 I/O pins are sufficient for multiple timed outputs and control-state management, while the UART provides a service or configuration channel for production testing. The device should operate from the same regulated 5 V domain used by the digital control circuitry, with appropriate bypassing near the supply pins. Because OTP memory cannot be rewritten in the field, lighting behavior should be validated before programming. LED current drivers must remain separate from the MCU pins, and grounding and return-current paths should be arranged to avoid injecting switching noise into the serial interface.
Önerilen
Instrumentation Front-End Control
The Z86E2112FSC is useful as the supervisory controller in a compact instrumentation product that combines a UART command interface with digital measurement-control signals. Its 8 KB OTP memory accommodates fixed setup, calibration tables, and command handlers, while 236 bytes of RAM can support temporary status and protocol data. The 32 I/O pins can be allocated among control signals, mode selection, alarm outputs, and external data devices. For a measurement product, analog front ends should remain separate and quiet, while the MCU ground and supply return should be routed to avoid disturbing sensitive signals. Confirm the UART baud-rate requirements, oscillator arrangement, and pin multiplexing directly from the manufacturer documentation.
Önerilen
Smart Sensor Hub
The Z86E2112FSC can act as the protocol hub for a compact sensor assembly that receives readings over UART and manages local digital controls. Its 12 MHz processing rate is appropriate for polling sensors, validating data, and updating indicators, while 32 I/O pins support sensor-enable signals, alarms, and configuration lines. A regulated 5 V rail and local decoupling support stable digital operation. The short 236-byte RAM budget requires a memory-efficient scheduler, so buffering should be kept bounded and application code should avoid unnecessary duplication. Because the OTP program memory is permanent, the sensor protocol and calibration behavior should be finalized before production programming.
Önerilen
Communications and Network Equipment Control
The Z86E2112FSC is appropriate for low-level control tasks in communications equipment, including status monitoring, configuration, and UART-linked subsystem management. Its 32 I/O pins provide ample parallel control capacity, while the 12 MHz Z8 core executes command processing and fault-state logic. The 5 V operating point integrates naturally with digital equipment rails, provided the board respects the device’s maximum supply voltage and decoupling requirements. In a network product, keep the MCU and UART traces physically separated from high-energy switching paths and maintain a controlled return-current path beneath the device where board construction permits. Use the complete manufacturer datasheet to confirm package pin multiplexing before layout release.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: Z86E2112FSC — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | Z86E2112PSC |
|---|---|---|
| Brand | Zilog | Zilog |
| Package | 44-pin LQFP | 44-pin LQFP |
| Architecture | 8-bit Z8 | 8-bit Z8 |
| Maximum Clock Speed | 12 MHz | 12 MHz |
| Program Memory | 8 KB OTP | 8 KB OTP |
| RAM | 236 x 8 bits | 236 x 8 bits |
| I/O Pins | 32 | 32 |
| Serial Interface | UART | UART |
| Nominal Supply Voltage | 5.00 V | 5.00 V |
| Maximum Supply Voltage | 5.50 V | 5.50 V |
Ana Farklılayıcılar
- Direct same-family drop-in candidate (karşılaştırma:Z86E2112PSC)
- Compact 44-pin integration (karşılaştırma:Z86E2112PSC)
- Production-oriented OTP program memory (karşılaştırma:Generic Flash-memory 8-bit MCU)
Tasarım Notları
Power the Z86E2112FSC from a regulated 5.00 V rail and keep the supply within the listed 5.50 V maximum. Place the manufacturer-recommended input capacitor close to the supply and ground pins, and route high-current loads away from the MCU’s supply trace. Verify startup voltage, ripple, and absolute-maximum limits in the complete datasheet because the available product summary does not specify those operating conditions.
Use the 44-pin LQFP footprint defined by the manufacturer and preserve the pin-1 orientation and land pattern exactly. Confirm every multiplexed UART, clock, reset, and I/O assignment before routing. Because this is a multi-pin leaded package, inspect solder-joint consistency and consider lead coplanarity allowances when selecting the assembly process.
Do not treat the OTP program memory as field-programmable Flash. Finalize firmware, boot behavior, calibration constants, and peripheral assignments before production programming, and establish a controlled device-programming workflow. Also verify the suffix-specific temperature grade and qualification of any Z86E2112PSC replacement; matching clock and memory alone does not establish full qualification.
Keep the UART traces short, route them over a continuous reference plane, and avoid coupling them directly to switching-node or high-current edges. Provide a common return path and place interface protection close to the connector. If the controller communicates with an external transceiver, validate logic levels, slew rate, grounding, and bus direction against the relevant interface datasheets.
Uyumluluk Bilgisi
The indexed product information identifies the manufacturer, package, memory, clock, supply voltage, RAM, I/O count, and UART, but it does not state the requested environmental or material-compliance statuses. AEC-Q100 is not applicable to this general-purpose microcontroller unless a separate automotive-qualified ordering variant is explicitly identified.