مصنوعات (46,000+)

TJA1028TK/5V0/10/Z - 5V LIN Transceiver | NXP
TJA1028TK/5V0/10/Z

TJA1028TK/5V0/10/Z - 5V LIN Transceiver | NXP

The NXP Semiconductors TJA1028TK/5V0/10/Z is a LIN 2.0/2.1/SAE J2602 and ISO 17987-4:2016-compliant half-duplex LIN transceiver with an integrated 5.0 V low-dropout voltage regulator rated to deliver up to 70 mA. It operates from a 4.5 V to 28 V supply, supports 10.4 kbaud LIN communication, and is packaged in an 8-HVSON surface-mount package measuring 3 mm by 3 mm. A LIN transceiver is an interface integrated circuit that connects a host microcontroller to a low-cost, single-wire automotive network. The LIN bus sits below the hierarchical level of a CAN network: LIN is a Local Interconnect Network commonly used for body electronics, comfort controls, lighting, seat functions, and other low-bandwidth vehicle nodes. The TJA1028 combines this network interface with a local regulator, allowing a compact node to obtain both LIN communication and a 5 V supply from one component. Key features include bus wake-up, low-power mode, TXD timeout protection, thermal shutdown protection, and under-voltage detection. The integrated regulator provides up to 70 mA for local circuitry, while the 4.5 V to 28 V external supply range supports typical 12 V vehicle electrical systems. Its LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 compatibility makes it suitable for standardized in-vehicle networks. Technically, the TJA1028 combines a LIN physical-layer transceiver with a regulated auxiliary output. The LIN side provides the physical signaling interface between logic-level TXD and RXD signals and the bus. The regulator side reduces the vehicle supply to a fixed 5.0 V. The manufacturer describes strong electrostatic robustness as a key design feature, which is important because vehicle wiring can be electrically noisy and subject to ESD events. Typical applications include LIN door modules, seat-control units, switch banks, climate-control peripherals, ambient-lighting controllers, and compact body-control nodes. The 5 V variant is especially useful when a local sensor or actuator requires a regulated 5 V rail while the node communicates with a LIN master through the same wiring harness. Design the 3 mm by 3 mm footprint on a multilayer board with short LIN routing, a stable ground connection, and protection appropriate to the vehicle harness. Follow the manufacturer datasheet for decoupling capacitors, LIN bus protection, pin assignments, and PCB footprint dimensions. The 70 mA regulator is intended for local logic loads rather than high-current actuators. This page consolidates the device specifications, compliant LIN standards, package details, functional family alternatives, and practical design guidance into an engineering-focused reference for evaluating and implementing compact LIN nodes.

RFQ رابطہ
TJA1028TK/5V0/20/J - 5V LIN Transceiver 8-HVSON | NXP
TJA1028TK/5V0/20/J

TJA1028TK/5V0/20/J - 5V LIN Transceiver 8-HVSON | NXP

The NXP Semiconductors TJA1028TK/5V0/20/J is a single-channel LIN bus transceiver with an integrated 5.0 V low-dropout voltage regulator, delivering up to 70 mA and packaged in an 8-pin HVSON 3 x 3 mm surface-mount package. It supports LIN 2.0, LIN 2.1, SAE J2602 and ISO 17987-4:2016 12 V networks. A LIN transceiver, also called a LIN interface controller or LIN system-basis chip, converts logic-level serial data between a microcontroller and a low-cost single-wire vehicle network. The TJA1028 combines bus-level receive and transmit functions with a local regulator, allowing a compact LIN node to power its host microcontroller or peripheral circuitry while communicating over the vehicle network. The principal features include a 5.0 V regulator output, regulator capability of up to 70 mA, LIN 2.0 and LIN 2.1 compatibility, SAE J2602 and ISO 17987-4:2016 12 V compliance, and strong electrostatic-discharge robustness. The 3 x 3 mm HVSON package includes an exposed pad for improved heat transfer when the integrated regulator dissipates power. The TJA1028 architecture is tailored to low-speed automotive and industrial LIN networks. Its integrated regulator reduces the number of discrete components needed for a basic LIN slave node, while the 8-pin package supports compact PCB placement. The product family is also offered in 3.3 V and 5.0 V regulator variants, allowing the interface voltage to match different host systems. Typical uses include LIN-controlled vehicle modules, body-control electronics, sensor interfaces, door and seat modules, climate-control peripherals, and compact industrial LIN nodes. The device is particularly suitable when a local 5 V rail is required alongside LIN communications and board space is tightly constrained. Use the manufacturer datasheet pin description and application circuit when assigning PCB tracks, decoupling, exposed-pad connections and bus protection. Confirm that the selected 5 V variant matches the host supply requirements and that the regulator load remains within the specified 70 mA capability. This page combines the TJA1028 family specifications, package details, supported LIN standards and same-footprint ordering variants with practical guidance for PCB implementation, sourcing and design selection.

RFQ رابطہ
TJA1028TK/5V0/20:1 - LIN Transceiver with 5V Regulator | NXP
TJA1028TK/5V0/20:1

TJA1028TK/5V0/20:1 - LIN Transceiver with 5V Regulator | NXP

The NXP Semiconductors TJA1028TK/5V0/20:1 is a LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 compliant half-duplex transceiver with an integrated low-dropout 5.0 V voltage regulator, a maximum regulated output current of 70 mA, and a 20 kbit/s version designation. It is packaged in an 8-HVSON surface-mount package with a 3 x 3 mm footprint and exposed pad. The integrated regulator supplies local electronics while the transceiver connects the node to a LIN bus. A LIN, or Local Interconnect Network, transceiver is an interface IC that converts logic-level signals between a host controller and a low-cost, single-wire automotive communication bus. LIN belongs to the broader vehicle network-interface hierarchy, where transceivers add the electrical protection and signal conditioning required to communicate reliably over a physically long, noisy harness. The TJA1028 combines this bus-interface role with a local power-supply function, reducing the component count needed by compact LIN nodes. The device provides a 5.0 V regulator variant with a stated output range of 4.9 V to 5.1 V. The regulator can deliver up to 70 mA, while the listed supply current is 4.5 mA. The /20 version is associated with a 20 kbit/s LIN communication class. NXP also lists operation from -40 degrees C to +150 degrees C, making the device suitable for demanding automotive environments. The package is identified as 8-HVSON (3 x 3 mm), and the exposed pad supports heat dissipation into the PCB. The TJA1028TK is designed for LIN 2.0, LIN 2.1, SAE J2602, and ISO 17987-4:2016 (12 V) applications. Its integrated 5.0 V regulator can power a local microcontroller, communication interface, or sensor circuitry without requiring a separate regulator in compact nodes. The device is intended for automotive and industrial LIN systems where a local 12 V bus must be converted into a regulated 5 V rail and a standardized LIN physical-layer signal. Typical uses include compact LIN sensor nodes, automotive body-control modules, LIN-to-CAN gateways, actuator interfaces, and industrial diagnostic or control nodes. The 3 x 3 mm HVSON package supports dense PCB layouts, but correct exposed-pad soldering and copper thermal design remain important. The regulator output and transceiver supply pins should be decoupled according to the application guidance in the NXP datasheet. Designers should confirm that the selected 5.0 V output variant matches the load voltage, that the total regulator demand remains below 70 mA, and that the communication speed suits the selected /20 device. LIN bus layout also requires controlled termination, adequate grounding, protection routing, and separation from high-current or high-voltage switching nodes. This page combines NXP product information, interface characteristics, package details, and practical implementation guidance for faster engineering evaluation.

RFQ رابطہ
TJA1029T - 20 kBd LIN 2.2 Automotive Transceiver | NXP
TJA1029T

TJA1029T - 20 kBd LIN 2.2 Automotive Transceiver | NXP

The NXP Semiconductors TJA1029T is a LIN physical-layer transceiver that connects a Local Interconnect Network master or slave protocol controller to the physical vehicle bus. It supports data rates up to 20 kBd, is intended primarily for in-vehicle subnetworks, and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. The device is supplied in an 8-pin SO package designated 8-SO. A LIN transceiver is a low-speed automotive network interface that converts serial protocol-controller data into a shaped bus signal and converts received bus levels back into logic-compatible data. Within the vehicle-network hierarchy, the TJA1029T belongs to the LIN physical layer, below the LIN protocol controller and above the twisted-pair LIN bus. This division separates frame-level communication and fault management from the electrical interface to the bus. The TJA1029T converts the protocol controller's transmit data stream into an optimized bus signal intended to minimize electromagnetic emissions. Its internal LIN-bus output pull-up and its ability to operate as either a master or slave physical interface suit vehicle subnetwork nodes. The NXP datasheet identifies the TJA1029 as pin-compatible with the TJA1020, TJA1021, TJA1022, TJA1027, and MC33662(B), providing a documented basis for same-footprint replacement evaluation. The device is primarily designed for automotive LIN subnets operating at up to 20 kBd. Typical implementation places the transceiver beside a LIN-compatible microcontroller, connects TXD and RXD to the controller, and connects the LIN pin to the vehicle's LIN bus. In this arrangement, the microcontroller handles protocol frames, addressing, diagnostics, and higher-level vehicle functions, while the TJA1029T performs the physical signaling and bus-interface functions. Because LIN buses commonly operate in harsh automotive environments, the complete transceiver and module design must be validated for the intended voltage, temperature, ESD, emission, and immunity requirements. The supplied verified data does not state the complete electrical limits, thermal ratings, timeout options, or exact pin names, so those details must be confirmed in the manufacturer datasheet and the selected ordering variant before schematic release or PCB sign-off. The main engineering tradeoff is version-specific functionality. Ordering codes such as TJA1029T/20/1J and TJA1029T/2Z appear in distributor records, with the latter identified as including a TXD dominant timeout, but the supplied excerpts do not provide a complete variant matrix. Engineers should therefore match the exact base-device and timeout features required by the LIN controller, firmware, safety analysis, and production BOM rather than selecting only by connector or package. This page consolidates the verified manufacturer statements, distributor availability references, documented pin-compatible alternatives, package information, and practical selection guidance. It also separates verified facts from unprovided electrical details, helping engineers identify valid drop-in candidates while avoiding unsupported assumptions about pricing, pin assignments, lifecycle guarantees, or automotive qualification.

RFQ رابطہ
TJA1029T/20/1J - 20 kbaud LIN Transceiver | NXP | Automotive
TJA1029T/20/1J

TJA1029T/20/1J - 20 kbaud LIN Transceiver | NXP | Automotive

The NXP TJA1029T/20/1J is an automotive LIN physical-layer transceiver with a 20 kbaud maximum bus speed, 5 V to 18 V supply range, and an 8-pin SOIC package. It interfaces a LIN master or slave protocol controller with the physical LIN bus and supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 for 12 V systems. A LIN transceiver is the physical-layer interface within a Local Interconnect Network. The LIN bus is a low-cost, single-wire automotive network derived from the automotive CAN hierarchy and commonly used for vehicle subnets. It connects sensors, actuators, switches, and electronic control units through a protocol controller, while the transceiver converts controller logic into a properly shaped bus signal and returns received bus data to the controller. The TJA1029 is optimized for in-vehicle subnetworks operating at baud rates up to 20 kBd. Its LIN bus output is shaped to minimize electromagnetic emissions, and the bus output is pulled high through an internal termination resistor. A TXD dominant-timeout function helps protect the network when the protocol controller fails to release the transmit signal. The device operates from 5 V to 18 V and is specified for an ambient temperature range of -40 °C to 150 °C. The TJA1029 is pin-compatible with the TJA1020, TJA1021, TJA1022, TJA1027, and MC33662(B) families according to the NXP datasheet. This compatibility supports design reuse when a product requires a different LIN transceiver feature set, although firmware, timing, protection, and application requirements should be reviewed before substitution. The integrated bus interface reduces the component count required for LIN physical-layer connections. Typical uses include body-control modules, door and seat controllers, climate-control interfaces, sensor gateways, lighting controllers, seat-memory modules, and other low-speed automotive subnetworks. The 20 kBd limit matches conventional LIN communication rates, while the broad 5 V to 18 V supply range supports automotive electrical environments when used with appropriate protection and decoupling. When laying out the PCB, use the manufacturer pin-definition table and recommended application circuit. Place the device-side and bus-side capacitors close to their intended pins, keep the LIN connection away from sensitive analog and high-speed digital traces, and provide a correctly sized bus termination. The LIN bus requires one master termination and slave-side pull-up arrangements defined by the network design. This page organizes the TJA1029T/20/1J specifications, protocol support, pin-compatible alternatives, application guidance, and design checks into one engineering reference. It helps distinguish direct family replacements from broader LIN-transceiver choices while keeping package compatibility and automotive operating requirements central to the selection process.

RFQ رابطہ
TJA1029T/2Z - 20 kBd LIN 2.2A Transceiver | NXP
TJA1029T/2Z

TJA1029T/2Z - 20 kBd LIN 2.2A Transceiver | NXP

The NXP Semiconductors TJA1029T/2Z is an automotive LIN physical-layer transceiver supporting bus speeds up to 20 kBd, LIN 2.0 through LIN 2.2A operation, and SAE J2602 compliance in an 8-pin SOIC package. It interfaces a LIN leader or follower protocol controller with the physical bus and adds a TXD dominant-timeout feature for systems requiring controlled transmitter behavior. A LIN transceiver is a physical-layer interface IC that combines a logic-level transmitter, receiver, bus-driver protection, and LIN bus termination functions. In the vehicle networking hierarchy, LIN connects low-cost nodes for body electronics and in-vehicle subnetworks, while the protocol controller manages frames and scheduling above the transceiver. The TJA1029 therefore bridges a digital controller and the wired LIN network rather than operating as a standalone bus controller. According to NXP product information, the device supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. Its principal purpose is in-vehicle subnetworks operating at up to 20 kBd. The verified distributor data identifies TJA1029T/2Z as a half-duplex LIN transceiver with TXD dominant timeout, which is useful where the host controller must avoid an indefinitely asserted transmit command. NXP states that TJA1029 is pin-compatible with the TJA1020, TJA1021, TJA1022, and TJA1027. That compatibility creates a controlled upgrade path within the same NXP interface family, although designers must still verify electrical limits, timing, fault behavior, package suffix, and production requirements for the specific replacement. The TJA1021T/20/C from the site MPN list is therefore an important family reference, not an automatically interchangeable part without checking its ordering code. Typical uses include LIN-controlled vehicle body modules, door and seat controllers, climate-control interfaces, lighting modules, sensor gateways, and other low-speed automotive subnetworks. The 20 kBd capability and LIN 2.2A/SAE J2602 positioning align it with established in-vehicle network architectures rather than high-speed body communication buses. The critical design check is the power and bus environment. Use the manufacturer datasheet for the exact VCC range, LIN transceiver operating limits, pin names, external termination, ESD requirements, and thermal limits before layout release. In particular, verify whether the selected SOIC footprint and pin mapping match the exact package variant being assembled.

RFQ رابطہ
TJA1029TK - 2.2A LIN Transceiver | NXP Semiconductors
TJA1029TK

TJA1029TK - 2.2A LIN Transceiver | NXP Semiconductors

NXP Semiconductors TJA1029TK is a 2.2 A LIN 2.2A and SAE J2602 transceiver with a transmit-data dominant timeout function, supplied in an 8-pin HVSON package measuring 3 x 3 mm. It supports LIN bus communication at rates up to 20 kBd and connects a Local Interconnect Network master or follower protocol controller to the physical LIN bus. A LIN transceiver is a physical-layer interface within an automotive communication network. The Local Interconnect Network is a low-cost, single-wire serial bus commonly used to connect relatively simple vehicle nodes such as sensors, switches, seat modules, and door electronics. A LIN transceiver converts the controller's transmit and receive signals into a bus-compatible waveform and reports received bus data back to the controller. The TJA1029 supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 communication requirements. Its stated 2.2 A bus-output capability supports the physical drive required in vehicle electrical environments, while its 20 kBd maximum signaling rate matches the communication range of LIN 2.x networks. The TXD dominant-timeout feature adds a defined protection function for the transmit-data path. NXP identifies the TJA1029 as pin-compatible with the TJA1020, TJA1021, TJA1022, and TJA1027 families. This compatibility provides a practical basis for PCB reuse when a design is being revised, although the selected replacement must still be checked for protocol version, timeout behavior, electrical limits, and ordering suffix requirements. Typical uses include LIN subnets containing door controls, climate-control modules, body controllers, seat electronics, lighting interfaces, and other distributed vehicle nodes. The device can serve as the physical interface in either a LIN leader or follower node because the protocol controller determines the network role independently of the transceiver. For layout, place the TJA1029 close to the LIN connector or protected bus entry point and minimize the distance of the LIN trace. The external bus network, connector, pull-up arrangement, protection components, and vehicle-level EMC requirements must be evaluated with the complete reference design rather than as isolated component choices. This product page consolidates the TJA1029TK identification, LIN standard coverage, known package information, pin-compatible family references, and practical replacement considerations. It also separates confirmed device facts from parameters that require confirmation in the NXP datasheet or a design-specific qualification before production release.

RFQ رابطہ
TJA1040T/CM - 1 MBaud CAN Transceiver | NXP
TJA1040T/CM

TJA1040T/CM - 1 MBaud CAN Transceiver | NXP

The NXP Semiconductors TJA1040T/CM is a high-speed CAN transceiver rated for operation up to 1 MBaud and supplied in an 8-pin SO package. It provides differential transmit capability to the physical CAN bus and differential receive capability to a CAN protocol controller, making it an interface between controller-area-network logic and vehicle or industrial bus wiring. A CAN transceiver is a physical-layer interface IC within the broader interface-IC hierarchy. It converts the controller’s digital logic signals into differential bus signaling and converts differential bus levels back into logic-compatible receive signals. The TJA1040 is intended primarily for high-speed passenger-car CAN networks, where robust differential signaling, standby control, and electromagnetic compatibility are important. The verified manufacturer information identifies differential transmission, differential reception, high-speed operation up to 1 MBaud, and standby-mode capability as principal device features. The distributor record identifies the TJA1040T/CM,118 ordering form as an 8-pin SO CAN-bus transceiver. Detailed electrical limits, loop-delay values, bus-fault behavior, and package dimensions were not supplied in the verified extract and therefore require confirmation from the manufacturer datasheet before design release. Typical uses include passenger-vehicle body and powertrain CAN networks, automotive control modules, CAN gateways, and industrial equipment that uses a 5 V CAN physical layer. The transceiver is intended to operate with a compatible CAN controller rather than as a standalone bus controller. Its differential bus interface supports robust communication over cable networks, while the standby function can reduce activity when the node is not communicating. Designers should preserve the pin assignment, supply decoupling, CANH/CANL routing, termination, and common-mode protection described by the manufacturer. The verified source set does not include the complete pinout, absolute maximum ratings, thermal data, or EMC test values, so those details must not be inferred. This page combines official NXP information with distributor records and explicitly marks unavailable parameters rather than estimating them. TJA1040T/CM is a legacy EoL-positioned part according to the supplied migration context. For new designs, engineers should compare it with current NXP or third-party CAN transceivers and verify pin, electrical, lifecycle, and qualification compatibility before treating any replacement as drop-in.

RFQ رابطہ
TJA1040T/N1 - 1 Mbit/s CAN Transceiver | NXP Semiconductors
TJA1040T/N1

TJA1040T/N1 - 1 Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1040T/N1 is a high-speed CAN bus transceiver with a maximum signaling rate of 1 Mbit/s, supplied in an 8-pin SO package. It provides the physical-layer interface between a CAN protocol controller and the differential CAN bus, combining a differential transmitter with a differential receiver. The device is intended primarily for high-speed in-vehicle passenger-car networks, where a compact controller-to-bus interface enables distributed automotive electronics to exchange safety, body, and powertrain-related data. A CAN transceiver is a semiconductor interface device that converts logic-level transmit and receive signals into the differential signaling used on a Controller Area Network. In the hierarchy of electronic components, the TJA1040T/N1 is an interface IC, specifically a CAN physical-layer transceiver. A host microcontroller or dedicated CAN controller handles message framing, arbitration, filtering, and protocol timing, while the transceiver translates those controller signals into robust bus-level voltages and converts received bus states into logic-compatible data. The key operating headline is a maximum data rate of 1 Mbit/s, with differential transmit and receive capability. The 8-SO package keeps the physical interface compact for automotive electronic control units and other embedded CAN systems. The NXP product page specifically identifies passenger cars as the principal application environment. These characteristics make the TJA1040T/N1 relevant to designs that need a conventional high-speed CAN physical layer rather than a low-speed fault-tolerant body-network interface. The TJA1040T/N1 belongs to an older generation of CAN transceivers whose successor products can add functions such as standby control, split-buffer operation, or expanded I/O voltage support. Its core role remains straightforward: TXD accepts a controller-side transmit signal, RXD presents the received bus state to the controller, and the differential CANH and CANL pins connect to the bus. Exact electrical limits, loopback behavior, and pin functions should be checked against the manufacturer data sheet before final circuit release. Typical applications include passenger-car body-control modules, powertrain controllers, automotive comfort systems, CAN-based sensors, and industrial or embedded equipment using a standard 1 Mbit/s CAN network. In an automotive control unit, the transceiver provides the physical link between a CAN controller and the two-wire bus while leaving protocol functions to the controller. Its differential interface also suits systems where minimizing susceptibility to common-mode noise is important. PCB design should preserve the short, symmetric CANH and CANL connection between the transceiver and the bus connector, keep the connector and bus stubs short, and provide the required decoupling directly at the device supply pins. The 8-SO footprint simplifies assembly but requires careful escape routing around the two bus pins. Review the recommended application circuit, termination requirements, supply voltage, and loopback configuration in the NXP data sheet when laying out the module. This product record combines the manufacturer interface description, ordering information, package details, lifecycle information, and replacement guidance with practical PCB considerations. It also distinguishes strict same-footprint substitutes from newer CAN transceivers that offer additional functions but may require different pin interpretation or board-level qualification.

RFQ رابطہ
TJA1040T/VM - 1Mbit CAN Transceiver | NXP | Automotive
TJA1040T/VM

TJA1040T/VM - 1Mbit CAN Transceiver | NXP | Automotive

The NXP TJA1040T/VM is a high-speed CAN physical-layer transceiver rated for data rates up to 1 Mbaud, operating from a 5 V supply, and packaged in an 8-pin SO small-outline package. It provides the differential transmitter and receiver interface between a CAN protocol controller and the physical CAN bus, making it suitable for passenger-car and other high-speed Controller Area Network systems. A CAN transceiver is an interface IC within the broader hierarchy of CAN interface devices, bus transceivers, wired-network interfaces, and semiconductors. It translates logic-level TXD and RXD signals into the differential CANH and CANL bus conductors and converts received bus differential voltage back into a logic-compatible RXD signal. This physical-layer function separates CAN protocol processing in a controller from the electrical drive, receive, and bus-failure behavior implemented by the transceiver. The TJA1040 supports high-speed CAN operation up to 1 Mbaud, making it appropriate for engine, chassis, body, and other automotive networks operating within that bandwidth. Its 5 V supply arrangement matches conventional automotive CAN interface environments. The device also provides power-down and standby operating states, allowing a system to reduce activity when communication is not required. The listed 8-SO package supports compact surface-mount PCB layouts. The transceiver architecture combines a differential CAN output stage with a differential input receiver. TXD is the controller-facing transmit input, while RXD is the controller-facing receive output. CANH and CANL provide the physical connection to the bus, VCC supplies the transceiver, VIO supports the interface voltage domain, and EN provides operating-state control. These functions allow a CAN controller to communicate through a multi-conductor differential bus while keeping protocol handling separate from bus signaling. Typical applications include passenger-car CAN networks, automotive body and chassis control modules, powertrain control equipment, industrial CAN equipment operating at compatible bus speeds, and embedded CAN gateways. In each application, the controller generates TXD and receives RXD, while the TJA1040 handles the physical bus interface. Board design must preserve the transceiver's supply, reference-ground, input, and bus-connection requirements to maintain signal integrity. When laying out the PCB, place the transceiver and its local decoupling capacitor close to the associated CAN controller, keep CANH and CANL routing compact and symmetrical, and provide the bus termination and common-mode network required by the selected CAN topology. Differential routing reduces sensitivity to external noise, while correct termination prevents excessive reflections from degrading communication at the maximum supported data rate. This product page combines the NXP device description with package, interface, application, comparison, and layout guidance. It also distinguishes verified source facts from engineering choices that depend on bus topology, termination strategy, controller supply voltage, and EMC validation.

RFQ رابطہ
TJA1041AT - 1 Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT

TJA1041AT - 1 Mbit/s High-Speed CAN Transceiver | NXP

NXP Semiconductors TJA1041AT is a high-speed CAN transceiver intended for automotive Controller Area Network nodes operating at data rates up to 1 Mbit/s. It provides differential transmit capability to the CAN bus and differential receive capability to the CAN protocol controller, with a 4.75 V to 5.25 V supply range and a 14-pin SOIC surface-mount package. The device is designed for use with a 5 V CAN controller interface. A CAN transceiver is the physical-layer interface between a CAN protocol controller and a wired CAN bus. Within the hierarchy of CAN interface ICs, CAN transceivers sit between microcontrollers or dedicated CAN controllers and the differential bus. They combine a transmitter, receiver, bus-driver protection, and logic-level interfaces into one component. This integration allows a protocol controller to exchange messages with other CAN nodes while the transceiver handles the physical signaling characteristics of the bus. The TJA1041AT supports CAN data rates up to 1 Mbit/s and is compatible with the ISO 11898 standard. Its differential transmitter and receiver support communication over a balanced CAN bus, while its digital transmit and receive pins connect to a CAN controller. NXP identifies the TJA1041AT as an end-of-life product, so long-lived automotive, industrial, and transportation programs should confirm lifecycle strategy and replacement planning with NXP before committing new production volumes. The SOIC-14 package provides separate connections for logic supply, transceiver supply, transmit data, receive data, standby control, CANH, and CANL. Its surface-mount construction supports automated PCB assembly, while the comparatively large lead pitch facilitates inspection and rework compared with fine-pitch packages. Precise pin names, truth-table behavior, electrical limits, and unused-pin connections should be assigned directly from the pin-description table and application information in the manufacturer datasheet. Typical uses include automotive body and powertrain networking, industrial automation equipment, transportation controllers, embedded CAN gateways, and diagnostic interfaces. The 1 Mbit/s capability suits conventional high-speed CAN networks used throughout vehicle and factory automation systems. A suitable host controller must support the device's logic levels, supply arrangement, standby behavior, and CAN protocol requirements. Designers should preserve the recommended transceiver and controller grounding arrangement, route CANH and CANL as a differential pair, and place protection or termination components where the bus topology requires them. Bus termination, common-mode range, loop delay, radiated emissions, and fault tolerance must be evaluated at system level rather than inferred solely from the nominal data rate. This product page combines the manufacturer lifecycle status, datasheet characteristics, application guidance, and cross-reference assessment to support engineering selection. It also distinguishes a genuine PCB-footprint replacement from merely similar CAN devices, avoiding the unsafe assumption that equal functionality automatically means pin-to-pin compatibility.

RFQ رابطہ
TJA1041AT/H/V - 1Mbps 5V CAN Transceiver | NXP
TJA1041AT/H/V

TJA1041AT/H/V - 1Mbps 5V CAN Transceiver | NXP

The NXP Semiconductors TJA1041AT/H/V is an automotive high-speed CAN transceiver supporting data rates up to 1 Mbit/s, operating from a 5 V supply and housed in a 14-pin SO package. It provides differential transmit and receive paths between a CAN protocol controller and the physical CAN bus, while standby and sleep functions support low-power automotive networking designs. A CAN transceiver is the physical-layer interface within a Controller Area Network node. The TJA1041A belongs to the hierarchy of CAN interface ICs, network controllers, interface transceivers and automotive communication semiconductors. Its differential bus interface supports robust communication over wired CAN networks, while its digital TXD and RXD connections simplify integration with a host microcontroller or dedicated CAN controller. The TJA1041AT/H/V is identified as an AEC-Q100 automotive-grade device. Its principal operating parameters include a maximum CAN data rate of 1 Mbit/s, a nominal 5 V supply and a 14-pin SO package. The family includes standby and sleep operating modes for applications where low quiescent consumption or controlled wake-up behavior is important. According to the NXP product information, the TJA1041AT is at End of Life, so engineers should confirm availability and lifecycle requirements before starting a new design. The device separates the CAN controller from the physical bus. TXD accepts the controller's transmit command, while RXD presents the received bus state to the controller. CANH and CANL form the differential pair connected to the bus. This architecture supports point-to-point communication rates of 500 kbit/s for classic CAN and 1 Mbit/s for high-speed CAN networks, subject to the complete system configuration and bus implementation. Typical applications include automotive body-control modules, powertrain controllers, instrument clusters, vehicle comfort systems, industrial CAN gateways, diagnostic equipment and embedded motor-control systems. In an automotive installation, the TJA1041AT/H/V can connect a CAN controller to a terminated differential network while standby and sleep modes help reduce activity during inactive operating periods. PCB implementation must preserve the CAN bus geometry, provide a low-impedance return path, and place transceiver and bus-termination components close to their associated controller or connector. A common split termination arrangement is useful when the transceiver sits at a remote board boundary. The 14-pin SO package should be inspected against the current NXP datasheet before assigning signals because board layouts must follow the manufacturer's exact pin descriptions. This product page combines the verified 1 Mbit/s, 5 V, 14-pin SO and AEC-Q100 attributes with lifecycle information, application guidance, comparison criteria and PCB-focused design notes. It is intended to help engineers identify whether this End-of-Life transceiver matches the electrical and mechanical requirements of an existing automotive or industrial CAN design.

RFQ رابطہ
TJA1041AT/N - 1 Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT/N

TJA1041AT/N - 1 Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041AT/N is a high-speed CAN bus transceiver for automotive applications operating at data rates up to 1 Mbit/s. It provides a physical-layer interface between a CAN protocol controller and the differential CAN bus, offering differential transmit and receive functions in a 14-pin SO package. Its nominal 5 V supply range is 4.75 V to 5.25 V. A CAN transceiver, also called a CAN physical-layer interface, converts logic-level signals from a CAN controller into differential bus signals and converts the received bus state back into a logic signal. Within the automotive electronics hierarchy, the TJA1041AT/N belongs to the CAN interface IC class, connecting the protocol-control layer to the physical communication bus. The principal feature of the TJA1041AT/N is its support for high-speed CAN communication up to 1 Mbit/s. Differential CAN signaling improves immunity to electromagnetic noise, while the transceiver's transmit and receive paths integrate the controller and bus into one physical-layer solution. The device is specifically intended for automotive high-speed CAN nodes, where robust differential signaling, compact packaging, and predictable interoperability are important. The TJA1041A family uses a nominal 5 V operating environment, with the documented supply range of 4.75 V to 5.25 V. The 14-pin SO package supports surface-mount PCB assembly and provides the CANH and CANL bus connections together with controller-facing TXD, RXD, and error-status signaling. Exact pin functions, absolute maximum ratings, loop-delay limits, and output-stage characteristics should be taken from the manufacturer datasheet. Typical deployments include automotive body and comfort modules, powertrain controllers, gateway units, cluster electronics, infotainment systems, and industrial CAN equipment that implements a compatible high-speed CAN physical layer. In these systems, the transceiver replaces discrete driver and receiver circuitry around the CAN controller while keeping the PCB layout compact. When laying out the circuit, place the transceiver close to the bus connector and route CANH and CANL as a matched differential pair. Keep the connection from CANH and CANL through the connector as short as practical, follow the datasheet recommendations for termination, and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. The NXP product page identifies TJA1041AT as end of life, so new designs should confirm the recommended successor before committing the footprint. This page combines the manufacturer's product information, datasheet links, distributor records, lifecycle information, and packaging details with practical application guidance, comparison parameters, and board-level design notes. It is intended to accelerate component selection and design-in work while keeping the final engineering decisions anchored to the official NXP documentation.

RFQ رابطہ
TJA1041AT/V - 1Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT/V

TJA1041AT/V - 1Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041AT/V is a high-speed CAN transceiver designed for automotive Controller Area Network nodes operating at data rates up to 1 Mbit/s. It provides differential transmit and receive capabilities between a CAN protocol controller and the physical CAN bus, operates from a 4.75 V to 5.25 V supply, and is offered in a 14-pin SO package. The device is intended for automotive electronic control units, body modules, instrumentation systems, and other embedded networking equipment that require a robust interface between a digital CAN controller and a differential bus. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. A CAN controller generates and interprets digital protocol frames, while the physical-layer transceiver converts controller signals into a differential CAN bus waveform and converts received bus levels back into logic-compatible receive data. The TJA1041AT/V therefore belongs to the CAN transceiver family, which operates at the physical-bus layer beneath communication controllers, embedded processors, and complete automotive electronic control units. Key operating features include support for high-speed CAN communication up to 1 Mbit/s, a 4.75 V minimum operating supply, a 5.25 V maximum operating supply, differential bus transmission, and differential bus reception. Its transceiver architecture allows a host controller to remain separate from the physical bus wiring while providing the electrical interface required for multi-node communication. The 14-pin SO package supports compact surface-mount assembly in automotive control-unit designs. The TJA1041A family is associated with ISO 11898 high-speed CAN communication and provides compatibility with CAN protocol controllers that provide TXD and RXD logic signals. The CANH and CANL connections carry complementary differential bus levels. This differential signaling improves common-mode noise rejection in vehicle electrical environments, where switching loads, alternator systems, and other transient-producing equipment can disturb the communication network. Typical applications include automotive body-control modules, powertrain controllers, gateway units, dashboard electronics, seat and door modules, lighting controllers, small electric motors, and industrial or transportation equipment using a CAN bus. In these systems, the transceiver is placed between the host CAN controller and the CANH and CANL network conductors. PCB routing, termination, grounding, and protection remain critical because the transceiver is only one element of the complete physical-layer network. Design the power and signal paths carefully around the 4.75 V to 5.25 V operating range. Decoupling should be placed close to the supply pins, the CANH and CANL traces should follow controlled-impedance routing practices, and the bus should use the termination strategy specified by the CAN network design. Protection components may be added when the cable environment includes severe automotive transients, provided their capacitance and clamping behavior do not distort the differential signal. This product page combines the NXP technical description with lifecycle information, package identification, practical interface guidance, sourcing questions, and clearly qualified replacement analysis. It also highlights where an existing design can be reused and where a new PCB and EMC validation are required before changing CAN transceivers.

RFQ رابطہ
TJA1041AT/VM - 1Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT/VM

TJA1041AT/VM - 1Mbit/s High-Speed CAN Transceiver | NXP

NXP TJA1041AT/VM is a high-speed CAN bus transceiver with differential transmit and receive capability, supporting CAN node data rates up to 1 Mbit/s in a 14-pin SOIC package. It provides the physical-layer interface between a CAN protocol controller and the physical CAN bus while supporting automotive high-speed CAN applications. The manufacturer identifies the TJA1041AT family as end-of-life, so new designs should confirm the status of a specific orderable variant before committing the layout. A CAN transceiver is the physical-layer interface within a Controller Area Network node. A CAN protocol controller generates and interprets CAN frames, while the transceiver converts between the controller's digital TXD and RXD signals and the differential CANH and CANL bus wires. This interface belongs to the hierarchy of CAN interface IC, communication transceiver, network interface, and semiconductor. Its differential bus operation supports noise-resistant communication over cables and PCB interconnects in automotive and industrial networks. The principal operating specification is support for high-speed CAN communication up to 1 Mbit/s. The device combines differential bus output with differential input reception, allowing a CAN controller to transmit dominant states and detect recessive states from the bus. A 14-pin SOIC package supports conventional surface-mount assembly, while the extended ambient-temperature specification of -40°C to +105°C suits industrial and automotive environments where temperature variation is significant. The TJA1041A architecture is designed specifically for connection between a CAN protocol controller and a physical CAN bus. Its transmit path drives the differential CANH and CANL conductors, and its receive path presents the bus state to the controller through RXD. Because the interface operates differentially, the receiver evaluates the voltage relationship between CANH and CANL rather than relying on a single conductor referenced only to ground, improving common-mode noise rejection in vehicle and industrial networks. Typical applications include automotive body and powertrain electronic control modules, industrial automation equipment, transport systems, embedded CAN gateways, and other distributed control networks. The part is most appropriate where the selected CAN controller uses a 3.3 V or 5 V TXD/RXD interface and the system requires the established 14-pin high-speed CAN transceiver footprint. Designers must still verify signal levels, loopback behavior, bus timing, and transceiver-mode requirements against their controller and network design. A critical design consideration is that an end-of-life status does not make a legacy transceiver automatically interchangeable with a newer CAN transceiver. Pin placement alone is insufficient: replacement devices can differ in standby, sleep, wake-up, split-mode, VIO, loopback, and bus-failure behavior. Validate the complete transceiver state machine, electrical limits, timing, and firmware expectations before using another MPN on an existing PCB. This product page combines the manufacturer's operating description, lifecycle status, package information, temperature range, replacement guidance, and pin-compatible family alternatives with practical selection and design notes. It is intended to accelerate engineering review by separating true footprint compatibility from broader functional similarity and by highlighting the checks required when maintaining an established automotive or industrial CAN design.

RFQ رابطہ
TJA1041T/H/V - 1Mbit/s High-Speed CAN Transceiver | NXP
TJA1041T/H/V

TJA1041T/H/V - 1Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041T/H/V is a high-speed CAN bus transceiver supporting data rates up to 1 Mbit/s, operating from a 5 V supply in a 14-pin SOIC package. It provides a differential CANH and CANL bus interface together with transmit and receive paths for connection between a CAN protocol controller and the physical CAN network. The device is designed for automotive high-speed CAN nodes and is compatible with the ISO 11898 standard. A CAN transceiver is an interface IC that translates logic-level signals from a CAN controller into differential physical-bus signals and converts received differential bus levels back into controller-compatible logic. In the hierarchy of electronic components, the TJA1041T/H/V is a CAN transceiver, which is a bus-interface device within the broader interface IC and semiconductor categories. Its primary role is to isolate the controller from the electrical characteristics, common-mode behavior, and fault conditions found on a wired CAN network. Key characteristics include operation at up to 1 Mbit/s, ISO 11898 compatibility, a nominal 5 V supply, and an operating temperature range of -40°C to +150°C. NXP describes the TJA1041 as providing excellent electromagnetic compatibility, very low power consumption, and passive behavior when the supply voltage is off. These characteristics make it relevant to automotive body, powertrain, chassis, and industrial CAN systems where bus reliability under temperature and electromagnetic stress is important. The transceiver uses differential signaling to improve common-mode rejection on the CAN bus. Its transmitter drives the CANH and CANL conductors, while its receiver interprets differential bus voltage. ISO 11898 compatibility provides a defined physical-layer framework for high-speed CAN communication. Because the TJA1041T/H/V does not include a CAN protocol controller, it must be paired with a controller containing CAN TX and RX logic rather than used as a standalone bus node. Typical applications include automotive electronic control units, body-control modules, powertrain controllers, industrial automation equipment, elevator controls, and embedded CAN gateways. The 1 Mbit/s capability suits conventional CAN systems, while the wide -40°C to +150°C operating range supports harsh industrial and automotive environments. Systems requiring a CAN controller with an integrated transceiver should use a different device family rather than adding this transceiver unnecessarily. Design attention should be directed to supply decoupling, termination, common-mode choke selection, protection against bus transients, and the separation of sensitive analog or communication paths from noisy power stages. A split termination network can improve EMC behavior, while a common-mode choke can reduce radiated emissions when appropriately selected. PCB placement should minimize loop area around the transceiver and bus-node components because long or poorly controlled high-current loops can increase emissions. This product reference combines lifecycle information, interface specifications, package details, application guidance, and same-package replacement considerations. It is intended to help engineers distinguish the original TJA1041T/H/V order code from related qualification and packing variants before making a PCB-compatible sourcing decision.

RFQ رابطہ
TJA1041T/N1 - 1Mbit/s CAN Transceiver | NXP | SOIC-14
TJA1041T/N1

TJA1041T/N1 - 1Mbit/s CAN Transceiver | NXP | SOIC-14

The NXP TJA1041T/N1 is a high-speed CAN transceiver designed to connect a CAN protocol controller to a physical Controller Area Network bus. It supports data rates up to 1 Mbit/s, provides one CAN transmit and receive path, and is offered in a 14-pin SOIC surface-mount package for automotive high-speed CAN systems. A CAN transceiver is an interface IC within the automotive network-communication hierarchy. It translates the controller's logic-level TXD and RXD signals into a differential bus waveform for transmission and converts received differential bus levels into a logic signal for the controller. This physical-layer function complements the CAN protocol controller, which handles message identifiers, arbitration, error handling, and higher-level data exchange. The TJA1041T/N1 provides differential transmit capability, differential receive capability, and compatibility with high-speed CAN protocol controllers operating up to 1 Mbit/s. Its single-transceiver arrangement suits conventional CAN nodes that do not require the additional transceiver features found in sleep-capable variants. The SOIC-14 package supports surface-mount assembly while providing separate pins for the bus interface, logic interface, ground connection, and stabilization. Automotive and industrial CAN networks benefit from the robust differential signaling inherent in the TJA1041 architecture. Differential reception rejects common-mode voltage present on the bus, while the controller and transceiver can use twisted-pair wiring to maintain signal integrity over longer cable runs. The manufacturer's product documentation identifies the device primarily for automotive high-speed CAN applications and confirms compatibility with suitable CAN protocol controllers. Typical deployments include engine-control units, transmission controllers, body-control modules, gateways, electronic control units, industrial automation controllers, and CAN-based sensor or actuator networks. In these systems, the TJA1041T/N1 handles the physical bus layer while a separate CAN controller manages frame arbitration, acknowledgments, error counters, and communication with the host processor. Designers should follow the manufacturer's recommended transceiver and bus-line application circuit, including termination, common-mode choke or split-termination options where required, decoupling, and PCB routing guidance. The 1 Mbit/s capability does not remove the need for controlled bus topology, adequate ground references, correct termination placement, and protection suited to the vehicle or industrial environment. This page combines the TJA1041T/N1 lifecycle information, verified source links, same-footprint alternatives, application guidance, and engineering design notes to support component selection, PCB planning, and long-term supply-risk assessment.

RFQ رابطہ
TJA1041T/VM - 1 Mbit/s CAN Transceiver | NXP Semiconductors
TJA1041T/VM

TJA1041T/VM - 1 Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1041T/VM is a high-speed Controller Area Network transceiver designed for automotive CAN nodes operating at speeds up to 1 Mbit/s. It provides differential transmit and receive functions between a CAN protocol controller and the physical CAN bus, and is offered in a 14-pin SOIC package. The TJA1041 family is listed as End of Life by NXP. A CAN transceiver is the physical-layer interface between a digital CAN controller and the differential bus wiring. It converts controller logic signals into a dominant or recessive differential bus state and converts bus levels into logic signals for the controller. This type of interface belongs to the hierarchy of CAN transceiver, communication interface IC, interface IC, and semiconductor. The TJA1041 supports CAN communication rates up to 1 Mbit/s and is primarily intended for high-speed automotive applications. Its differential receiver provides the interface from the bus to the controller, while its differential transmitter connects the node to the CAN network. The TJA1041T/VM package designation identifies the SOIC-14 variant with NXP's VM ordering suffix. Automotive electronics use CAN networks to connect engine-control, body, chassis, comfort, and diagnostic modules while reducing wiring complexity. A CAN node generally combines a protocol controller with a transceiver such as the TJA1041. The physical transceiver handles bus-level signaling, allowing the controller to exchange frames through a standardized communication interface. Typical uses include electronic control units, body-control modules, powertrain controllers, gateway electronics, automotive diagnostic interfaces, and industrial CAN equipment connected to 1 Mbit/s networks. Selection should consider bus speed, transceiver logic compatibility, termination strategy, package footprint, operating temperature, and the manufacturer's lifecycle status. PCB design must preserve the recommended CAN bus routing and termination arrangement, provide a stable transceiver supply, and maintain suitable common-mode behavior for the automotive network. Because the TJA1041T/VM is marked End of Life, new production designs should verify migration options and avoid depending on an unannounced second source. This product page combines the NXP functional description, package and lifecycle information, ordering references, and practical guidance for selecting, comparing, and implementing a replacement before an End of Life migration.

RFQ رابطہ
TJA1042AT/0Z - 5Mbps High-Speed CAN Transceiver | NXP
TJA1042AT/0Z

TJA1042AT/0Z - 5Mbps High-Speed CAN Transceiver | NXP

The NXP TJA1042AT/0Z is a high-speed CAN bus transceiver with one transmitter and one receiver, a maximum data rate of 5 Mb/s, and an SOIC-8 surface-mount package. Its 4.5 V to 5.5 V supply range and -40°C to +150°C operating-temperature range make it appropriate for demanding industrial and automotive communication systems. The TJA1042AT/0Z also provides Standby-mode operation, including the bus-wake-up capability described for the TJA1042 family. A CAN transceiver is an interface IC that connects a CAN protocol controller, such as a microcontroller with an integrated CAN controller, to a physical two-wire CAN bus. The transceiver converts the controller's logic-level transmit command into a differential CANH/CANL bus signal and converts the differential bus voltage into a logic-level receive output. Within the product hierarchy, a CAN transceiver belongs to the interface IC class, the CAN interface subclass, and ultimately the broader semiconductor category. The TJA1042AT/0Z provides a data rate of up to 5 Mb/s, one CAN transmitter, one CAN receiver, and a specified operating supply current of 80 mA. Its 4.5 V minimum and 5.5 V maximum supply voltages support conventional 5 V automotive and industrial CAN systems. Standby mode helps reduce system consumption when the bus is inactive, while the family's bus-wake-up behavior supports systems that must detect remote bus activity. The family is designed for high-speed CAN applications in the automotive industry and includes differential transmit and receive capability between a CAN controller and a two-wire bus. NXP describes the TJA1042 as a third-generation high-speed CAN transceiver. Its SOIC-8 construction provides a conventional surface-mount option for PCBs requiring a small, widely supported package, although the actual exposed-pad and soldering details should be confirmed against the manufacturer package drawing. Typical uses include automotive body and powertrain control modules, industrial automation equipment, robotics controllers, building automation gateways, and other embedded systems that exchange data over a CAN bus. In these systems, the controller handles CAN frames and protocol timing, while the TJA1042AT/0Z handles the physical-layer differential signaling. Its 5 Mb/s capability accommodates high-speed CAN traffic, and its -40°C to +150°C specification supports wide environmental ranges. PCB design should preserve the transceiver's supply decoupling, ground connection, controller-interface traces, and CAN bus routing. Place the supply capacitor close to the device and keep the CANH and CANL route as a closely coupled differential pair. The bus conductors require suitable termination, protection, and common-mode considerations; exact resistor and capacitor values are application-dependent and are not specified by the verified source excerpts. This product record combines the verified NXP datasheet information with distributor availability, package details, temperature limits, supply limits, and a bulk pricing schedule as of 2026-10-28. It also distinguishes the TJA1042AT/0Z from related TJA1042 and modern TCAN transceiver options so engineers can assess PCB compatibility and functional differences before selecting a replacement.

RFQ رابطہ
TJA1042AT/3/0Z - 5Mbps CAN Transceiver | NXP
TJA1042AT/3/0Z

TJA1042AT/3/0Z - 5Mbps CAN Transceiver | NXP

The NXP Semiconductors TJA1042AT/3/0Z is a high-speed CAN transceiver with a 5 Mbps maximum data rate, differential CAN bus transmit and receive functions, a 5 V supply, and an 8-pin SOIC package. It provides the physical-layer interface between a CAN protocol controller and a two-wire CAN network, with the /3 version supporting a VIO supply for direct interfacing with 3.3 V or 5 V controller logic. A CAN transceiver is an interface IC that converts logic-level TXD and RXD signals into the differential CANH and CANL bus signals used by Controller Area Network systems. Within the hierarchy of CAN interface ICs, physical-layer transceivers connect automotive and industrial network controllers to the bus while adding bus protection, standby behavior, and standardized digital interfaces. The TJA1042 family is specifically designed for high-speed automotive CAN networks. Principal features include a maximum CAN data rate of 5 Mbps, one-transceiver one-receiver organization, differential bus output, low-power Standby mode, and VIO support in the /3 version. The separate VIO rail allows the controller-facing pins to operate from a lower voltage while CANH, CANL, and the transceiver core use the 5 V supply. The Arrow product listing identifies the device as an automotive AEC-Q100 8-pin SOIC transceiver. The TJA1042AT/3/0Z uses pin 5 as VIO rather than the SPLIT common-mode stabilization function found on the TJA1042T version. This distinction is important during replacement because the two suffix families do not have identical pin 5 functions. The /3 device also provides bus wake-up capability and passive behavior when unpowered, characteristics that support low-power automotive networking and robust bus integration. Typical applications include automotive body and chassis control modules, powertrain and gateway controllers, industrial CAN equipment, robotics, and embedded transport systems. It is particularly suitable where a microcontroller or dedicated CAN controller requires a 5 Mbps physical interface while its digital I/O operates at 3.3 V. The low-power Standby function helps reduce current consumption when the node is not actively communicating. When laying out a circuit, place the transceiver close to the CANH and CANL connector, keep the bus traces short and matched, and provide the decoupling and common-mode components recommended by the NXP TJA1042 manufacturer datasheet. Verify that VIO is connected correctly on the /3 version and that PCB exposure, automotive qualification, and temperature requirements match the intended installation. This page combines the NXP manufacturer datasheet, product listings, verified drop-in candidates, interface comparisons, and practical PCB guidance. It helps engineers identify the correct /3 variant, distinguish VIO from SPLIT implementations, and plan a CAN transceiver layout without relying on a generic SOIC-8 pinout.

RFQ رابطہ
TJA1042ATK/3/0Z - 5Mbps CAN FD Transceiver | NXP
TJA1042ATK/3/0Z

TJA1042ATK/3/0Z - 5Mbps CAN FD Transceiver | NXP

NXP Semiconductors TJA1042ATK/3/0Z is a high-speed CAN and CAN FD transceiver with a maximum data rate of 5 Mbit/s, a 5 V transceiver supply, and an 8-HVSON exposed-pad package measuring 3 x 3 mm. It provides the physical-layer interface between a CAN protocol controller and a two-wire CAN bus, combining high-speed data transfer with low-power standby operation. A CAN transceiver is an interface IC that converts logic-level controller signals into differential CAN bus levels and reconstructs bus signals for the controller. Within the communication hierarchy, the TJA1042ATK/3/0Z belongs to the CAN transceiver class, interface ICs, wired-communication semiconductors, and automotive electronics. Its differential bus interface supports robust automotive networking while the transceiver handles electrical protection and bus interfacing. Key characteristics include support for communication rates up to 5 Mbit/s, a 4.5 V to 5.5 V transceiver operating range, and a low-power Standby mode with bus wake-up capability. The automotive-grade version is identified as AEC-Q100 compliant in the product listing. Its 8-HVSON package uses an exposed pad to improve heat dissipation while keeping the PCB footprint compact. The TJA1042 family is designed for reliable CAN and CAN FD communication with improved electromagnetic compatibility and electrostatic-discharge performance. The passive behavior of the bus pins when the device is unpowered helps a connected node avoid disrupting communication from other operating nodes. These characteristics are useful in distributed automotive and industrial control networks where cable length, electromagnetic interference, and partial power loss are important system considerations. Typical applications include automotive body and chassis control modules, industrial CAN gateways, vehicle diagnostic interfaces, battery-management systems, and distributed automation controllers. A CAN protocol controller or MCU with an integrated CAN controller connects to the TJA1042 through TXD, RXD, and enable-related pins, while CANH and CANL connect to the bus through the network termination and protection scheme. For PCB implementation, place the transceiver close to the CAN bus connector and keep the CANH and CANL traces short, symmetric, and free from switching nodes. Follow the manufacturer pin and layout guidance when connecting the exposed pad, supply decoupling, split-capacitor option, bus termination, and protection components. Account for the common-mode and transient-voltage environment of an automotive bus. This page combines the exact ordering information, electrical envelope, automotive qualification, package details, drop-in alternatives, application guidance, and design considerations needed to evaluate the TJA1042ATK/3/0Z before PCB implementation or sourcing.

RFQ رابطہ
TJA1042T - 1 Mbps High-Speed CAN Transceiver | NXP Semiconductors
TJA1042T

TJA1042T - 1 Mbps High-Speed CAN Transceiver | NXP Semiconductors

Buy the NXP TJA1042T 1 Mbps high-speed CAN transceiver in an 8-pin SOIC with standby mode. Compare alternatives, verify pinout and lifecycle, and request current supply.

RFQ رابطہ
TJA1042T/1J - High-Speed CAN Transceiver | NXP | Automotive
TJA1042T/1J

TJA1042T/1J - High-Speed CAN Transceiver | NXP | Automotive

The NXP TJA1042T/1J is a high-speed CAN transceiver with standby mode, providing the physical-layer interface between a CAN protocol controller and a differential two-wire CAN bus. The device is packaged as an 8-pin SOIC and is identified by DigiKey as a 1/1 half CAN-bus transceiver. The verified NXP product page describes it as a high-speed CAN transceiver with standby mode, while the manufacturer datasheet states that it supplies differential transmit and receive capability for automotive CAN systems. A CAN transceiver is an interface IC that converts logic-level TXD and RXD signals into the dominant and recessive voltage levels carried by a CAN bus. It also places the bus-side driver and receiver between the controller and the physical network, helping the controller communicate over a robust multi-node differential bus. The TJA1042 family belongs to the broader CAN transceiver, communication interface, interface IC, and semiconductor hierarchy. The key verified feature set is high-speed CAN operation, differential transmit and receive, standby operation, 8-pin SOIC packaging, and automotive-oriented application positioning. The standby function is useful when a node must reduce activity while retaining the CAN interface. The exact maximum data rate, supply range, loop delay, bus fault behavior, thermal limits, and electrical thresholds are not present in the supplied verified excerpts, so those values must be confirmed from the complete manufacturer datasheet before design release. The TJA1042 is intended for automotive electronic control units, body controllers, powertrain controllers, gateway modules, instrument clusters, and other embedded systems that use a CAN protocol controller. In a typical circuit, the MCU CAN controller connects to TXD and RXD, while CANH and CANL connect to the external bus through the board's approved network interface and termination arrangement. The transceiver is the boundary between digital controller signaling and the differential physical bus. Designers should verify the exact NXP ordering code, supply voltage, transceiver mode timing, bus termination, common-mode environment, loop delay, and external-component recommendations against the complete TJA1042 datasheet. Because the supplied web data does not expose a complete pin-level table, pricing schedule, compliance declaration, or lifecycle statement, those items are marked as needing verification rather than inferred. The TJA1042T/1J is best evaluated by engineers who need a standby-capable, high-speed CAN physical-layer device in an SOIC footprint.

RFQ رابطہ
TJA1042T/1U - High-Speed CAN Transceiver | NXP | SOIC-8
TJA1042T/1U

TJA1042T/1U - High-Speed CAN Transceiver | NXP | SOIC-8

The NXP Semiconductors TJA1042T/1U is a high-speed CAN transceiver with standby mode, packaged in an 8-pin SOIC. It provides the physical-layer interface between a CAN protocol controller and a differential two-wire CAN bus. The device supports the transmit, receive, standby, split and bus-fault functions expected from a high-speed automotive CAN transceiver, while its SOIC-8 format supports conventional surface-mount PCB assembly. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. It converts logic-level TXD and RXD signals from a CAN controller into the dominant and recessive differential levels carried by CANH and CANL. Conversely, it converts the differential bus voltage into a logic-compatible receive signal. This physical-layer function allows a microcontroller or dedicated CAN controller to communicate reliably with other nodes on a shared network. The TJA1042T/1U differentiates itself through its standby operating mode and split functionality. Standby mode lets the node reduce activity when it is not required to participate fully in bus communication. The split function is associated with stabilizing recessive bus behavior and can be important in systems containing more than one CAN node. NXP markets the TJA1042T family for high-speed CAN applications in the automotive industry. The TJA1042T/1U is identified as an NRND product on the official NXP product page. NRND means the product is not recommended for new designs, so engineers should evaluate the lifecycle position and any successor named by NXP before committing a new production platform to this MPN. Existing designs may still use the part, but procurement and long-term availability require confirmation from authorized distributors. Typical uses include distributed automotive control modules, body electronics, electric vehicle subsystems, industrial CAN gateways, sensor nodes and engine or transmission control units. The differential bus interface lets these systems exchange data reliably over distances and wiring arrangements that would be unsuitable for ordinary single-ended digital signaling. Local CAN-controller I/O voltage compatibility must also be checked during design review. PCB implementation requires care around the CANH and CANL connections. The two bus conductors should follow the impedance and routing guidance in the manufacturer datasheet, with a common-mode choke or split capacitor used only when the reference network requires it. Decoupling should be placed close to the supply pins, and unused device functions must be connected exactly as specified in the datasheet rather than according to generic transceiver schematics. This page consolidates the verified NXP product information, distributor package identification, sourcing context, lifecycle status and practical design guidance. It distinguishes documented facts from values that require confirmation from the current manufacturer datasheet, helping engineers evaluate the TJA1042T/1U without treating incomplete distributor snippets as complete electrical specifications.

RFQ رابطہ