AD504MH - 0.3 MHz Military Op Amp | Analog Devices
MPN: AD504MH ✗ اختتامِ زندگیAD504MH جائزہ
An operational amplifier is an active semiconductor device that amplifies the difference between two input voltages. Within the broader hierarchy of an op amp, analog amplifier, voltage amplifier, and semiconductor, the AD504MH provides high open-loop gain, differential input capability, and an output stage suitable for low-frequency precision control systems. Its general-purpose architecture allows it to support feedback-based signal conditioning without a fixed internal application.
The AD504MH's headline characteristics include a 500 uV maximum input offset voltage, a 0.3 MHz bandwidth, an 18 V maximum supply rating, and a nominal slew rate of 0.12 V/us. The offset specification supports accurate DC amplification, while the 0.3 MHz bandwidth identifies the device as a low-frequency amplifier rather than a high-speed signal-conditioning component. The hermetic TO-99 construction supports use in environments where mechanical protection and stable electrical performance are important.
This older military-grade amplifier is used for precision DC amplification, feedback control, instrumentation, low-frequency filter stages, and signal conversion. Its 0.12 V/us slew rate limits large-signal response, so applications should avoid demanding full-bandwidth operation or fast pulse reproduction. Input and output timing should also be checked against the 0.3 MHz bandwidth rather than the much higher open-loop gain available at low frequencies.
Typical circuit roles include amplifier stages in test and measurement systems, sensor-signal conditioning, servo or feedback control, analog reference systems, and low-frequency active filters. The single-amplifier configuration permits direct implementation of inverting, non-inverting, differential, and comparator-style arrangements when the system operating conditions support them. The 8-pin metal-can package also offers a mechanically robust alternative to modern plastic packages.
Circuit implementation requires attention to supply decoupling, input common-mode range, output swing, bias-current effects, and stability with the selected feedback network. Place suitable bypass capacitance close to the supply pins, keep feedback-loop routing compact, and verify loop gain against the amplifier's frequency response. Because this is a hermetically sealed TO-99 device, lead bending and soldering should use procedures suited to metal packages.
This product record consolidates the AD504MH's confirmed electrical and mechanical characteristics, sourcing information, package details, and application-oriented engineering guidance. It also distinguishes confirmed ratings from parameters that require consultation of the manufacturer datasheet before release of a production design.
کے لیے ڈراپ اِن متبادل AD504MH — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس پروڈکٹ کے لیے کوئی ڈراپ اِن متبادل دستیاب نہیں۔
متبادل کی درخواست کریںAD504MH زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Product Type | Single general-purpose operational amplifier |
| Input Offset Voltage | 500 uV maximum |
| Gain-Bandwidth Product | 0.3 MHz |
| Maximum Supply Voltage | 18 V |
| Nominal Slew Rate | 0.12 V/us |
| Number of Amplifiers | 1 amplifier |
| پیکیج | 8-pin TO-99 |
| Package Shape | Round |
| Package Construction | Hermetically sealed |
| Terminal Form | Wire |
| Number of Terminals | 8 terminals |
| Temperature Grade | Military grade |
| ماؤنٹنگ ٹائپ | Through-hole |
AD504MH hermetically sealed پن کنفیگریشن گائیڈ
AD504MH (hermetically sealed پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں AD504MH.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
AD504MH کے لیے موزوں ہے 6 ایپلیکیشنs: Precision Instrumentation Signal Conditioning, Military Feedback Control, Low-Frequency Active Filter, Sensor Interface Amplification, Test and Measurement Front End, Power Supply Feedback Monitoring.
Precision Instrumentation Signal Conditioning
The AD504MH fits low-frequency precision signal-conditioning stages because its 500 uV maximum input offset voltage limits DC error when the amplifier operates with appreciable closed-loop gain. The 0.3 MHz bandwidth is suitable for sensors, measurement transducers, and laboratory signals that require amplification rather than high-speed waveform capture. A practical implementation places the amplifier in an inverting or non-inverting feedback network and places the compensation or feedback components close to the device. The main trade-off is the 0.12 V/us nominal slew rate, which restricts large-signal bandwidth. Input common-mode range, output swing, bias current, and noise must be confirmed from the manufacturer datasheet before setting the gain and operating range.
تجویز کردہ
Military Feedback Control
The AD504MH is appropriate for legacy military feedback-control blocks where hermetic sealing, the military-grade designation, and preservation of the 8-pin TO-99 interface are priorities. Its 0.3 MHz gain-bandwidth product can support servo, actuator, and feedback loops operating well below that frequency, while the 500 uV maximum offset helps reduce command-error contribution in DC-coupled control paths. The implementation should use conservative loop gain and compensation because both the closed-loop bandwidth and nominal 0.12 V/us slew rate limit transient response. Designers must also observe the 18 V supply rating, verify input and output operating ranges, and use the manufacturer package drawing for lead spacing and orientation in ruggedized equipment.
تجویز کردہ
Low-Frequency Active Filter
The AD504MH can form an active low-pass or band-pass stage in systems that need gain and filtering around DC or low audio-rate frequencies. Its 0.3 MHz gain-bandwidth product leaves headroom below the closed-loop cutoff selected for the feedback network, while the 500 uV maximum offset supports low-frequency operation where offset drift becomes important. Component tolerances and the amplifier's open-loop response directly influence filter accuracy, so simulate the complete network rather than assuming ideal behavior. Keep the feedback loop compact and verify phase margin across the intended passband. The 0.12 V/us nominal slew rate should be checked against the largest expected transient, and supply bypassing should be placed close to the TO-99 leads.
تجویز کردہ
Sensor Interface Amplification
The AD504MH is useful for amplifying outputs from relatively slow sensors where low offset and simple single-amplifier implementation are important. A 500 uV maximum input offset specification is helpful when the sensor signal is small and the closed-loop noise gain is high, while the 0.3 MHz bandwidth readily covers many temperature, position, pressure, and strain-gauge conditioning channels. The circuit must remain within the amplifier's input common-mode range and output swing, particularly when using a single supply. Bias-current compensation may be needed for high-impedance sources. Confirm the source impedance, sensor excitation scheme, cable capacitance, and expected temperature range in the manufacturer datasheet before finalizing the input network.
تجویز کردہ
Test and Measurement Front End
The AD504MH can serve as the analog front-end amplifier in legacy test and measurement equipment that operates primarily at low frequencies. The 500 uV maximum input offset helps preserve accuracy when the front end amplifies small DC or slowly changing signals, and the single-amplifier format provides a straightforward route to inverting, non-inverting, or differential configurations. The 0.3 MHz bandwidth is suitable for many process-control and analog diagnostic measurements but does not support high-speed digitizer front ends. Use short feedback paths, verify stability with the intended source and load impedances, and select capacitors that remain appropriate across the operating range. The hermetically sealed TO-99 construction supports installation in long-life analytical or industrial test systems.
تجویز کردہ
Power Supply Feedback Monitoring
The AD504MH can amplify small voltage-deviation signals for slow power-supply feedback or supervisory monitoring circuits. Its 500 uV maximum input offset is meaningful when the monitored deviation is small, and its 0.3 MHz bandwidth covers control loops that do not require high-frequency transient reproduction. A practical design compares the feedback signal with a reference, amplifies the resulting error, and uses the output as a correction or monitoring signal. The designer must verify that the common-mode voltage at the amplifier inputs remains inside its permitted range under minimum and maximum supply conditions. The nominal 0.12 V/us slew rate is adequate only when correction signals change slowly. Use local decoupling and maintain a compact feedback loop to reduce susceptibility to board noise.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا AD504MH — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Brand | Analog Devices |
| Package | 8-pin TO-99 |
| Product Type | Single general-purpose operational amplifier |
| Maximum Offset Voltage | 500 uV |
| Gain-Bandwidth Product | 0.3 MHz |
| Maximum Supply Voltage | 18 V |
| Nominal Slew Rate | 0.12 V/us |
| Temperature Grade | Military grade |
| Package Construction | Hermetically sealed |
| Terminal Form | Wire |
اہم امتیازی خصوصیات
- Maximum input offset voltage (بمقابلہNo confirmed replacement MPN)
- Hermetically sealed metal package (بمقابلہNo confirmed replacement MPN)
- Military-grade identification (بمقابلہNo confirmed replacement MPN)
ڈیزائن نوٹس
Use the Analog Devices TO-99 package drawing to define lead spacing, drill diameters, and pin-one orientation before releasing the board layout. Place the device near the associated feedback components and route the feedback loop as a short, compact path. Because this is a through-hole hermetic package rather than a surface-mount device, inspect lead alignment after insertion and avoid excessive force that could stress the glass-to-metal seals.
The AD504MH has a 0.3 MHz gain-bandwidth product and a nominal 0.12 V/us slew rate, so stability and transient response depend strongly on the selected feedback network. Simulate the complete loop with the intended source impedance, load, and compensation values. Keep feedback components close to the amplifier, maintain a short ground return, and verify phase margin before adding high-frequency noise, capacitive loading, or cable-driven input capacitance.
Estimated: with an 18 V maximum supply rating, the amplifier must be operated within the manufacturer limits for supply voltage, input common-mode range, and output swing. Keep the supply rails below 18 V, add appropriate bypass capacitance at the device, and account for startup and transient current in the power architecture. Confirm the actual operating current from the AD504MH datasheet before sizing the supply and ground-return components.
Do not treat the 8-pin TO-99 package shape as proof of pin compatibility. The pin functions, compensation requirements, offset-null connections, common-mode range, and output limits must be checked against the AD504MH manufacturer datasheet. Also avoid assuming that any other military-grade op amp is interchangeable; use the exact terminal assignment and electrical limits for the proposed replacement before energizing the circuit.
تعمیل کی معلومات
The military-grade designation is confirmed, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was found for this MPN. Verify the applicable compliance status with the manufacturer before using the part in a regulated production design.