Analog Devices

AD708AH - Ultra-Low Offset Dual Op Amp | Analog Devices

MPN: AD708AH ✓ فعال
30 µV Vdss 25 pA/°C Id 8-pin ceramic DIP Package
MOQ: 1 |

AD708AH جائزہ

Analog Devices AD708AH is a very high precision, dual monolithic bipolar operational amplifier with two independent amplifiers, a maximum input offset voltage of 30 µV, maximum offset voltage drift of 0.3 µV/°C, minimum open-loop gain of 5 V/µV, and an 8-pin ceramic DIP package. It is designed for instrumentation, sensor signal conditioning, precision current measurement, and other applications requiring exceptional DC accuracy.

An operational amplifier, commonly called an op amp, is a high-gain differential amplifier that uses external feedback to control gain and signal behavior. The AD708 belongs to the precision bipolar operational-amplifier family, which is part of the broader amplifier IC and semiconductor hierarchy. Its two amplifiers can perform independent functions in one package or support differential, filtering, and feedback configurations when their electrical matching is beneficial.

The AD708AH emphasizes precision rather than speed. Analog Devices specifies maximum input offset voltage of 30 µV and maximum offset voltage drift of 0.3 µV/°C. The device also provides a minimum open-loop gain of 5 V/µV, a minimum CMRR of 130 dB, and a minimum PSRR of 120 dB. These characteristics reduce errors in slow sensor signals, low-level voltage measurements, and precision feedback networks.

Noise performance is similarly suited to demanding measurements. The guaranteed maximum input voltage noise is 350 nV peak-to-peak from 0.1 Hz to 10 Hz. This low-frequency noise specification is important when the input source is a bridge, thermocouple, strain gauge, or other transducer with output signals in the microvolt-to-millivolt range. The manufacturer also describes typical offset-voltage drift of 0.1 µV/°C and maximum input bias-current drift of 25 pA/°C.

Typical uses include precision bridge amplifiers, low-level sensor interfaces, instrumentation amplifiers, laboratory measurement equipment, and high-accuracy current-feedback circuits. The dual configuration can reduce board area when a design needs two precision gain stages. Because an op amp can saturate or behave unexpectedly outside its common-mode range, engineers should verify input and output voltage limits against the operating conditions of the complete circuit.

A careful design should account for bias-current error, input offset voltage, resistor tolerance, and thermoelectric effects. Place the device close to sensitive input nodes, maintain a symmetric resistor network around each amplifier, and use low-noise, low-temperature-coefficient resistors when the measurement budget is tight. Stable reference and supply sources also help prevent input-common-mode and power-supply variations from dominating the remaining error.

This page organizes the AD708AH electrical characteristics, drop-in substitution status, application guidance, and design considerations into one engineering reference. It also explains where datasheet-level checks are required before precision measurements, PCB implementation, or lifecycle-dependent sourcing decisions.

کے لیے ڈراپ اِن متبادل AD708AH — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

AD708BQ

✅ ڈراپ-اِن
📦 8-CERDIP
Same AD708 family and 8-CERDIP format; exact offset, temperature, and ordering-suffix differences require datasheet confirmation.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

AD708AH زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Product Type Dual precision bipolar operational amplifier
Number of Amplifiers 2 amplifiers
Maximum Input Offset Voltage 30 µV
Maximum Offset Voltage Drift 0.3 µV/°C
Typical Offset Voltage Drift 0.1 µV/°C
Minimum Open-Loop Gain 5 V/µV
Minimum CMRR 130 dB
Minimum PSRR 120 dB
Maximum Input Voltage Noise 350 nV peak-to-peak from 0.1 Hz to 10 Hz
Maximum Input Bias Current Drift 25 pA/°C
Maximum Offset Voltage Match 30 µV
Supply Voltage Span ±22 V
Total Power Dissipation 650 mW
Architecture Monolithic bipolar
پیکیج 8-pin ceramic DIP
ماؤنٹنگ ٹائپ Through-hole

AD708AH 8-pin ceramic dip پن کنفیگریشن گائیڈ

AD708AH (8-pin ceramic dip پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

AD708AH کے لیے 8-pin ceramic dip پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں AD708AH.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

AD708AH کے لیے موزوں ہے 6 ایپلیکیشنs: Precision Bridge Sensor Signal Conditioning, Strain Gauge Measurement Front Ends, Thermocouple and Low-Level Voltage Acquisition, Precision Current Measurement, Laboratory Instrumentation Signal Chains, High-Accuracy Sensor Interface Modules.

🏭

Precision Bridge Sensor Signal Conditioning

The AD708AH fits low-level bridge measurements because each amplifier offers a maximum input offset voltage of 30 µV, maximum offset drift of 0.3 µV/°C, and a minimum CMRR of 130 dB. It can be used in a differential amplifier around a resistive bridge, converting small differential sensor outputs into a higher-level measurement signal while rejecting common-mode voltage. The design should use a matched resistor network and keep input traces short because resistance and layout mismatch can otherwise exceed the amplifier’s inherent offset performance.

🏭

Strain Gauge Measurement Front Ends

Strain-gauge outputs can be extremely small and temperature-sensitive, making the AD708AH’s 30 µV maximum offset voltage and 0.3 µV/°C maximum drift useful in a precision front end. Its 5 V/µV minimum open-loop gain supports accurate amplification of low-level differential signals, while 130 dB minimum CMRR helps reject environmental common-mode disturbances. Engineers should verify input bias current against the sensor’s source resistance and include sensor warm-up and thermal drift in the uncertainty budget.

🌡️

Thermocouple and Low-Level Voltage Acquisition

A thermocouple produces a small differential voltage, so amplifier offset and noise can materially affect temperature accuracy. The AD708AH provides a guaranteed maximum input voltage noise of 350 nV peak-to-peak from 0.1 Hz to 10 Hz, together with 30 µV maximum offset voltage. This makes it suitable for precision low-frequency acquisition when paired with proper input filtering and protection. Place the amplifier near the sensor connection, avoid unnecessary copper area, and account for parasitic thermocouple voltages at solder junctions.

⚡

Precision Current Measurement

The AD708AH can amplify the voltage produced by a small shunt resistor when high common-mode rejection and low offset are required. Its 120 dB minimum PSRR reduces sensitivity to supply variation, while 130 dB minimum CMRR helps reject differential noise appearing on both shunt terminals. For accurate results, use a low-TCCT shunt, Kelvin connections where appropriate, and an amplifier input network that avoids leakage currents. The bidirectional nature of the two amplifiers also supports complementary current and voltage channels.

🔧

Laboratory Instrumentation Signal Chains

The AD708AH is appropriate for laboratory buffer and gain stages where a 30 µV maximum input offset voltage and 0.3 µV/°C maximum drift help preserve small DC signals. Its dual monolithic construction can implement two related precision channels in one 8-pin ceramic DIP package. In a bench instrument, minimize thermal gradients across the package and use symmetrical layouts around both inputs. Stability should be verified with the exact feedback network, load, supply, and output range used in production.

🧩

High-Accuracy Sensor Interface Modules

Compact sensor-interface modules benefit when two low-level channels can share one precision dual amplifier. The AD708AH offers 130 dB minimum CMRR, 120 dB minimum PSRR, and typically 0.1 µV/°C offset drift, helping preserve signal integrity before digitization. The ceramic DIP package also supports through-hole assembly and prototype rework. Board design should provide local supply bypassing, clean grounding, and input protection without introducing leakage or nonlinear behavior at the sensor interface.

What is the AD708AH?
The AD708AH is a dual precision bipolar operational amplifier from Analog Devices, with a maximum input offset voltage of 30 µV and maximum offset voltage drift of 0.3 µV/°C. It contains two amplifiers in an 8-pin ceramic DIP package. According to the Analog Devices AD708 datasheet, the device is intended for precision DC signal conditioning where low offset, high open-loop gain, and strong common-mode rejection are important.
What are the key specifications of AD708AH that engineers should know?
The AD708AH combines a 30 µV maximum input offset voltage, 0.3 µV/°C maximum offset drift, 5 V/µV minimum open-loop gain, 130 dB minimum CMRR, and 120 dB minimum PSRR. Its guaranteed maximum input voltage noise is 350 nV peak-to-peak from 0.1 Hz to 10 Hz. The Analog Devices AD708 datasheet identifies the part as a monolithic bipolar dual op amp with two matching amplifiers.
Where can I download the AD708AH datasheet PDF?
The official AD708AH datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD708.pdf. It contains the electrical characteristics, amplifier descriptions, package details, and application information. Because the AD708AH is a temperature- and grade-specific ordering code, engineers should use the ordering information in the manufacturer datasheet when confirming the exact ceramic-DIP package and operating-temperature variant.
Where can I find the AD708AH pinout?
The AD708AH pin assignment and package drawing are shown in the pin-configuration section of the Analog Devices AD708 datasheet. The AD708AH uses an 8-pin ceramic DIP package. Assign pins by the manufacturer’s drawing rather than by visual position alone, and verify the dual-amplifier orientation, supply pins, offset-trim connections, and input pins before laying out a new PCB.
What is the input offset voltage of the AD708AH?
The AD708AH has a maximum input offset voltage of 30 µV, according to the Analog Devices AD708 datasheet. This figure applies to each precision bipolar amplifier in the dual package. For practical error calculations, include the input bias-current drop, resistor-network imbalance, noise contribution, and any required offset trim when establishing the total measurement uncertainty.
How much does the AD708AH offset voltage drift with temperature?
The AD708AH guarantees a maximum offset-voltage drift of 0.3 µV/°C, while the Analog Devices AD708 datasheet reports a typical offset drift of 0.1 µV/°C. This makes the device appropriate for precision measurements where temperature changes can otherwise create an error comparable to the input signal. The actual system drift also depends on the matched feedback resistors, reference voltage, and thermal conditions around the amplifier.
What is the input noise of the AD708AH?
The AD708AH guarantees a maximum input voltage noise of 350 nV peak-to-peak over 0.1 Hz to 10 Hz. According to the Analog Devices AD708 datasheet, this low-frequency performance supports measurements involving slow, low-level signals. Noise at higher frequencies and the noise contributed by the surrounding resistors and reference circuitry must also be considered when setting the overall noise floor.
Is the AD708AH suitable for precision sensor measurement?
The AD708AH is suitable for bridge, strain-gauge, thermocouple, and other low-level sensor interfaces because of its 30 µV maximum offset voltage and 130 dB minimum CMRR. It is especially useful when the signal changes slowly and temperature drift dominates the error budget. The input common-mode range, supply arrangement, and sensor grounding should be checked against the Analog Devices AD708 datasheet before finalizing the circuit.
What can replace the AD708AH?
The AD708AH can be replaced only after confirming package outline, pin assignment, amplifier topology, supply range, offset, drift, noise, bias current, and temperature grade. The documented cross-reference search identifies one Analog Devices pin-to-pin alternative but does not provide its MPN or full parameter comparison. For that reason, no substitute is presented as a qualified drop-in without a specific manufacturer ordering code and verified compatibility.
Is the AD708AH the same as the AD708?
The AD708AH is an orderable version of the Analog Devices AD708 family, but a complete equivalence assessment must use the package and temperature-ordering information. The verified product information identifies AD708AH as an 8-pin ceramic-DIP implementation of the precision dual bipolar amplifier family. Do not treat the family name AD708 as proof that every package and grade has identical pin compatibility.
AD708AH versus another precision dual op amp: which is better for instrumentation?
The AD708AH is preferable when the design prioritizes exceptional DC precision, including 30 µV maximum offset voltage, 0.3 µV/°C maximum offset drift, 130 dB minimum CMRR, and 120 dB minimum PSRR. Another amplifier should be selected when lower power, higher bandwidth, lower cost, or a smaller package is more important than maximum DC accuracy. The final choice requires a full error-budget comparison rather than a generic op-amp substitution.
When should I choose the AD708AH over a general-purpose dual op amp?
Choose the AD708AH when low-level DC signals make offset voltage, offset drift, bias-current stability, and common-mode rejection the dominant errors. Its 30 µV maximum offset and 0.3 µV/°C maximum drift provide a measurable advantage over general-purpose amplifiers in bridge and instrumentation circuits. Use a faster or lower-power part when the signal bandwidth, supply consumption, or board area is the primary constraint.
Can the AD708AH be used in an instrumentation amplifier?
The AD708AH can participate in a precision instrumentation-amplifier design because its two amplifiers provide low offset voltage, low offset drift, high CMRR, and high PSRR. The matched amplifiers are particularly useful in differential signal chains. Resistor-network tolerance and mismatch still contribute to gain error and common-mode rejection, so precision resistors and careful layout remain necessary for the best achievable performance.
Where can I buy the AD708AH online?
Use the Request a Quote form on this page to request the AD708AH and obtain current commercial availability, lead time, and order details. The verified listings identify the exact AD708AH ordering code, but they do not provide a qualifying quantity-break price table for that exact MPN. Current sourcing status should therefore be confirmed through the quote workflow rather than inferred from an aggregator listing.
What is the lead time for the AD708AH?
The current lead time for AD708AH should be requested through the Request a Quote form on this page. A distributor search result and a general cross-reference listing do not establish a guaranteed delivery interval or current factory lead time. When requesting a quotation, specify the required quantity, package form, and date on which the complete shipment must be received.

کے لیے انجینئرنگ ریفرنس ڈیٹا AD708AH — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the AD708AH when the signal is small, slow, and accuracy is more important than bandwidth, power consumption, or unit cost. Its 30 µV maximum offset voltage, 0.3 µV/°C maximum drift, 130 dB minimum CMRR, and 120 dB minimum PSRR make it a strong fit for bridge sensors, precision current measurement, thermocouple interfaces, and laboratory instrumentation. Select a general-purpose dual op amp when the input signal has substantial bandwidth, system power is constrained, or an exact drop-in alternative with a documented MPN offers better overall economics. Before substituting any device, verify the package outline, pin assignment, supply range, input and output common-mode limits, offset, drift, noise, bias current, and temperature grade. The documented cross-reference search does not identify enough specific part numbers to publish five qualified drop-in replacements without risking an incompatible substitution.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ
Brand Analog Devices
Package 8-pin ceramic DIP
Amplifier Count 2
Architecture Monolithic bipolar
Maximum Input Offset Voltage 30 µV
Maximum Offset Voltage Drift 0.3 µV/°C
Minimum Open-Loop Gain 5 V/µV
Minimum CMRR 130 dB
Minimum PSRR 120 dB
Maximum Input Voltage Noise 350 nV peak-to-peak from 0.1 Hz to 10 Hz
Supply Voltage Span ±22 V
Total Power Dissipation 650 mW

اہم امتیازی خصوصیات

  • Exceptionally low guaranteed offset voltage (بمقابلہGeneral-purpose dual operational amplifier)
  • Low offset drift for changing temperatures (بمقابلہGeneral-purpose dual operational amplifier)
  • High rejection of common-mode and supply disturbances (بمقابلہGeneral-purpose dual operational amplifier)

ڈیزائن نوٹس

Keep each amplifier’s input traces short, symmetric, and away from switching nodes and high-current return paths. The AD708AH’s 130 dB minimum CMRR and 120 dB minimum PSRR support accurate rejection of common-mode and supply disturbances, but layout-induced leakage or pickup can still create errors. Use a continuous ground reference, avoid routing beneath sensitive inputs, and place input protection components close enough that their leakage remains controlled.

Do not calculate expected accuracy from the 30 µV maximum offset voltage alone. Include offset drift across the expected temperature range, input bias-current error, resistor tolerance and mismatch, reference accuracy, and 0.1 Hz to 10 Hz input noise. For low-level bridge or thermocouple measurements, use matched, low-noise resistors and include connector or solder-junction thermoelectric effects when the measurement resolution is in the microvolt range.

Confirm the complete circuit’s supply and common-mode limits against the Analog Devices AD708 datasheet before energizing the amplifier. The device supports a ±22 V span, but that does not make every operating point safe: input common-mode voltage, output swing, input differential voltage, and load current must also remain within their specified limits. Provide local supply bypassing and check startup behavior so an input or output condition does not remain outside the amplifier’s linear operating region.

For precision measurements, treat temperature gradients across the package as a design variable. The guaranteed maximum offset drift is 0.3 µV/°C, while typical drift is 0.1 µV/°C. Place the device away from regulators, switching converters, and other heat sources when possible, maintain consistent airflow, and avoid placing one amplifier near a warm reference while the other remains near a cold source. Differential drift can undermine matching even when absolute room-temperature specifications are met.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The Analog Devices product and datasheet excerpts do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for AD708AH. AEC-Q100 is not applicable to this precision analog operational amplifier.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-09 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

AD708AH datasheet AD708AH pinout AD708AH datasheet pdf AD708AH specifications AD708AH equivalent AD708AH replacement AD708AH cross reference AD708AH application circuit AD708AH offset voltage AD708AH input noise AD708AH price AD708AH stock Analog Devices AD708AH AD708AH precision dual op amp AD708AH ceramic DIP

متعلقہ اجزاء اور اصطلاحات

Analog Devices AD708 AD708AH precision operational amplifier dual operational amplifier bipolar operational amplifier monolithic amplifier amplifier IC semiconductor input offset voltage offset voltage drift open-loop gain common-mode rejection ratio CMRR power supply rejection ratio PSRR input voltage noise input bias current bridge sensor strain gauge thermocouple instrumentation amplifier precision current measurement ceramic DIP package
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں