ADM202EARWZ - 2-Channel ±15kV RS-232 Transceiver | Analog Devices
MPN: ADM202EARWZ ✓ فعالADM202EARWZ جائزہ
An RS-232 transceiver is an interface IC that combines a differential line driver and receiver for communicating between computers, instruments, industrial controllers, and other equipment. The driver converts TTL-compatible logic into bipolar RS-232 signals, while the receiver converts bipolar RS-232 signals back into logic levels. The ADM202EARWZ belongs to the RS-232 interface hierarchy, where robust protection, supply efficiency, and signal timing determine reliable performance in electrically noisy environments.
Key features include two driver and two receiver channels, operation from a single +5 V supply, four external 0.1 µF charge-pump capacitors, and compliance with EIA-232-E and CCITT V.28 specifications. The enhanced device supports data rates up to 230 kbps. Its protection features include ±15 kV ESD protection on transmitter outputs and receiver inputs, making the interface suitable for industrial, instrumentation, and data-transfer equipment.
The on-chip voltage-doubling and inverter circuitry generates the bipolar voltage required by RS-232 without a separate power supply. This architecture permits compact implementation while preserving standard-compatible logic interfaces. The manufacturer identifies the ADM202E family as a robust, pin-compatible upgrade for existing ADM202, ADM232L, and MAX202E/MAX232E sockets when the appropriate package and pin arrangement are used.
Typical uses include industrial control interfaces, laboratory instrumentation, barcode and data-acquisition equipment, embedded service ports, and legacy peripheral connections. The ADM202EARWZ is especially useful where equipment must retain an RS-232 port while adding stronger ESD protection and operation at rates as high as 230 kbps.
PCB design should keep the charge-pump capacitors close to their designated pins, route each RS-232 conductor away from sensitive analog and high-speed digital traces, and provide a low-impedance ground path between the transceiver and the connected equipment. Designers should also follow the manufacturer’s pin and polarity guidance to avoid confusing the transmit and receive paths.
This product overview combines the manufacturer’s technical descriptions with practical guidance for protection, layout, application selection, and replacement assessment. It is intended to help engineers determine whether the ADM202EARWZ’s 16-pin implementation, 5 V supply requirement, channel count, and enhanced ESD rating fit a specific RS-232 interface.
کے لیے ڈراپ اِن متبادل ADM202EARWZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ADM202EARWZ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Supply Voltage, Interface Standard, Product Type.
ADM202ARWZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM202EARUZ
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADM202ARUZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM202ARW
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM202EARWZ تفصیلات
| Product Type | 2-channel RS-232 line driver/receiver transceiver |
| Number of Driver Channels | 2 channels |
| Number of Receiver Channels | 2 channels |
| سپلائی وولٹیج | 5 V |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 230 kbps |
| RS-232 Output Level | Approximately ±10 V |
| Charge-Pump Capacitors | 4 external capacitors at 0.1 µF |
| ESD Protection | ±15 kV |
| Interface Standard | TIA/EIA-232-E and CCITT V.28 |
| پیکیج | 16-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
| Packaging | Tape & reel |
ADM202EARWZ 16-pin soic پن کنفیگریشن گائیڈ
ADM202EARWZ (16-pin soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ADM202EARWZ.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
ADM202EARWZ کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Interfaces, Laboratory Test Equipment, Embedded Service Ports, Data Acquisition Systems, Barcode and Identification Equipment, Legacy Peripheral Connectivity.
Industrial Control Interfaces
The ADM202EARWZ is appropriate for legacy industrial controllers and service equipment that retains an RS-232 port. Its 2-channel architecture supports bidirectional point-to-point communication from a single 5 V supply, while the enhanced ±15 kV ESD rating improves resilience on externally accessible serial connectors. Two driver and two receiver channels provide enough connectivity for a complete console or control link. The device supports operation up to 230 kbps, allowing it to handle command traffic, diagnostic data, and configuration exchanges without moving to a faster differential bus. In a typical installation, the logic-side pins connect to a microcontroller or embedded controller and the RS-232 side connects to the external equipment through a protected cable.
تجویز کردہ
Laboratory Test Equipment
The ADM202EARWZ fits laboratory instruments that need a legacy computer-control port alongside a 5 V logic supply. The 230 kbps maximum data rate supports reliable transfer of measurements, commands, and status information over short RS-232 cables. Because laboratory instruments may be connected and disconnected frequently, the ±15 kV ESD protection is a meaningful advantage over an unprotected legacy interface. The four external 0.1 µF charge-pump capacitors are the principal external support components and should be positioned according to the manufacturer layout. Its 2-channel arrangement can handle transmit and receive paths on one compact device, reducing board area compared with separate driver and receiver packages.
تجویز کردہ
Embedded Service Ports
The ADM202EARWZ is suitable for embedded systems that retain a service connector for configuration, diagnostics, or firmware recovery. Operating from 4.5 V to 5.5 V allows use around common 5 V digital rails, and the 230 kbps rate is adequate for interactive command consoles and diagnostic protocols. Enhanced ±15 kV ESD protection is especially useful when a service port connects to a chassis-mounted cable that may carry electrostatic discharge. The 16-pin SOIC package supports conventional surface-mount assembly, while the integrated charge pump avoids a separate negative voltage supply. Logic-side signals connect to the embedded controller, and the two bipolar driver and receiver channels provide flexible point-to-point connectivity.
تجویز کردہ
Data Acquisition Systems
The ADM202EARWZ can connect a data-acquisition controller to a legacy serial instrument or terminal. Two full RS-232 channels allow command transmission and measurement reception, while the 230 kbps limit supports moderate-rate acquisition control and short data bursts rather than continuous high-bandwidth streaming. The device’s single 5 V architecture simplifies power planning around logic-intensive measurement hardware. Its ±15 kV ESD protection improves reliability when cables connect external equipment that may be at different ground potentials. The transmit and receive paths should be routed as a matched pair, with the charge-pump section isolated from sensitive measurement circuitry. Keep grounding and cable returns arranged to minimize common-mode voltage at the receiver inputs.
تجویز کردہ
Barcode and Identification Equipment
The ADM202EARWZ is useful in barcode readers, identification terminals, and configuration tools that communicate through RS-232. The 2-channel arrangement supports bidirectional command and status traffic, and the 230 kbps capability is more than adequate for typical identifier payloads and short diagnostic records. A single 5 V supply reduces power complexity in compact equipment, while ±15 kV ESD protection adds resilience at a connector that may be exposed during installation or maintenance. Designers should preserve the bipolar RS-232 signal path, observe the charge-pump capacitor layout, and avoid substituting a TTL-level UART directly at the connector. The 16-pin SOIC footprint simplifies assembly where space is limited but full industrial environmental protection is still required.
تجویز کردہ
Legacy Peripheral Connectivity
The ADM202EARWZ enables modern controller boards to communicate with legacy printers, analyzers, and peripheral controllers that expose RS-232 connectors. It provides the required bipolar driver outputs and receiver inputs without requiring a separate negative supply. Operation up to 230 kbps accommodates typical peripheral-control protocols, while the enhanced ESD rating is valuable when the port is exposed to user-accessible cabling. The logic side connects to a host controller through standard digital levels, and the line side connects through the specified RS-232 network interface. Because RS-232 is point-to-point, confirm that each driver connects to a receiver and that no multi-drop arrangement is being attempted. Proper grounding and short external cables remain necessary for dependable communication.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ADM202EARWZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ADM202ARWZ | ADM202EARUZ | ADM202ARUZ | ADM202ARW |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Product Family | Enhanced ADM202E | ADM202 | Enhanced ADM202E | ADM202 | ADM202 |
| ESD Protection | ±15 kV | Lower protection rating than ADM202EARWZ | ±15 kV | Lower protection rating than ADM202EARWZ | Lower protection rating than ADM202EARWZ |
اہم امتیازی خصوصیات
- Enhanced electrostatic-discharge protection (بمقابلہADM202ARWZ)
- High-speed RS-232 operation (بمقابلہADM202ARWZ)
- Single-supply bipolar output generation (بمقابلہADM202ARW)
ڈیزائن نوٹس
Place the four 0.1 µF charge-pump capacitors close to the pins identified in the manufacturer’s reference layout. Keep each capacitor’s connection to the device short, symmetrical, and free of unnecessary loop area because these components carry switched charge-pump current. Confirm capacitor voltage rating, tolerance, and dielectric requirements from the official datasheet before layout release.
Separate the charge-pump and RS-232 driver routing from sensitive receiver inputs and unrelated low-level analog traces. Route each RS-232 signal as a driver-to-receiver point-to-point connection with a corresponding ground reference, and avoid long unshielded branches. The approximately ±10 V driver outputs require spacing appropriate to the board’s fabrication and isolation requirements.
Do not connect the ADM202EARWZ receiver directly to a TTL UART because the receiver expects bipolar RS-232 levels. Also avoid treating the 16-SOIC outline as sufficient proof of interchangeability: verify the exact pinout, package width, supply limits, temperature grade, and ESD requirement. The 230 kbps figure is a maximum supported rate and should not replace signal-integrity and timing validation in the target cable environment.
تعمیل کی معلومات
The enhanced ADM202E family is described as compliant with the EU EMC directive 89/336/EEC. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated for the exact MPN in the available technical information.