Analog Devices

ADM3491ARZ - 3.3V Full-Duplex RS-485/RS-422 | Analog Devices

MPN: ADM3491ARZ ✓ فعال
3.3 V Vdss 840 µA Id EIA RS-422 and EIA RS-485 Rds(on) 14-lead SOIC Package
MOQ: 1 |

ADM3491ARZ جائزہ

The Analog Devices ADM3491ARZ is a low-power differential line transceiver designed for operation from a single +3.3 V power supply. It supports 10 Mbps data rates, full-duplex RS-422 and RS-485 communication, 5 V logic interoperability, short-circuit protection, and a low 840 µA supply current. The device is offered in a 14-lead SOIC package for industrial data links and multipoint transmission systems.

A differential line transceiver is an interface integrated circuit that combines a transmitter and receiver to communicate over balanced, differential pairs. RS-422 is commonly used for point-to-point links, while RS-485 supports multipoint buses. These standards belong to the broader wired-data-interface hierarchy, where transceivers connect low-voltage digital logic to external cables carrying larger-amplitude differential signals.

Key features include a 3.3 V operating supply, 10 Mbps maximum signaling rate, 19 kΩ receiver input impedance, and support for up to 50 transceivers on a bus. The receiver remains compatible with 5 V logic, which simplifies interfaces between newer 3.3 V systems and older digital controllers. A shutdown mode reduces supply current to 2 nA, making the device suitable for power-sensitive systems that are intermittently active.

The ADM3491 family provides EIA RS-422 and RS-485 compliance across the full common-mode range. Its 8 ns transmit skew supports balanced timing between differential outputs, while reduced slew rates on related family members address electromagnetic-interference requirements. Short-circuit protection and thermal shutdown improve robustness when a driver encounters an abnormal bus condition.

Typical uses include industrial automation links, data acquisition equipment, building-control systems, instrumentation, and communications equipment requiring a full-duplex balanced interface. The 10 Mbps capability is appropriate for factory-floor links, while the 19 kΩ input impedance permits multiple receivers on a bus without excessive loading.

PCB design should preserve the differential signal path and provide a controlled return route. Place input and output bypassing capacitors close to their associated supply pins, and keep connector and protection-device return currents from crossing the differential pair. Confirm the exact pin names and exposed connections in the manufacturer datasheet before assigning PCB nets.

This page combines application guidance, engineering design notes, and structured cross-reference information to support faster transceiver selection and board bring-up. The ADM3491ARZ is suited to engineers who need a compact, low-power, 3.3 V full-duplex RS-422 or RS-485 interface with 10 Mbps operation.

کے لیے ڈراپ اِن متبادل ADM3491ARZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ADM3491ARZ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Product Type, Package, Maximum Data Rate, Logic Compatibility, Receiver Input Impedance.

Analog Devices
Product Type: Differential RS-485/RS-422 line transceiver
Package: 8-SOIC, 3.90 mm width
Logic Compatibility: Interoperable with 5 V logic
موازنہ کریں ADM3491ARZ →
Analog Devices
Product Type: Low-power differential RS-485/RS-422 line transceiver
Maximum Data Rate: 20 Mbps
موازنہ کریں ADM3491ARZ →
Analog Devices
Product Type: RS-485/RS-422 differential line transceiver
Package: 14-pin SOIC
موازنہ کریں ADM3491ARZ →

ADM3491AR-1

✅ ڈراپ-اِن
📦 14-lead SOIC
Temperature-grade ordering designation differs while the 3.3 V full-duplex RS-422/RS-485 function and 14-lead SOIC package remain comparable

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

ADM3491ARZ-1

✅ ڈراپ-اِن
📦 14-lead SOIC
The -1 ordering suffix differs from the target suffix, with no documented change to the core 10 Mbps transceiver function

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

ADM3491-1

✅ ڈراپ-اِن
📦 14-lead SOIC
Family-level ordering designation uses the -1 grade while retaining the 3.3 V RS-422/RS-485 transceiver architecture

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

ADM3491ARZ-REEL7

✅ ڈراپ-اِن
📦 14-lead SOIC
Delivery orientation differs in the ordering code, while the electrical device and 14-lead SOIC footprint remain the same

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

ADM3491ARZ تفصیلات

Product Type Full-duplex differential line transceiver
Supported Standards EIA RS-422 and EIA RS-485
سپلائی وولٹیج 3.3 V
Maximum Data Rate 10 Mbps
Receiver Input Impedance 19 kΩ
Maximum Transceivers per Bus 50 transceivers
سپلائی کرنٹ 840 µA
شٹ ڈاؤن کرنٹ 2 nA
Logic Compatibility 5 V logic interoperable
Transmit Skew 8 ns
Common-Mode Range Full common-mode range
Short-Circuit Protection Yes
تھرمل شٹ ڈاؤن Yes
آپریٹنگ درجہ حرارت -40 °C to +85 °C
پیکیج 14-lead SOIC
ماؤنٹنگ ٹائپ Surface mount
EIA RS-485 Transient Immunity IEC 1000-4-4 above 1 kV

ADM3491ARZ 14-lead soic پن کنفیگریشن گائیڈ

ADM3491ARZ (14-lead soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

ADM3491ARZ کے لیے 14-lead soic پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ADM3491ARZ.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

ADM3491ARZ کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Automation Bus Interface, Factory Data Acquisition, Building Control Network, Instrumentation Communication, Point-to-Point Data Link, Power-Sensitive Sensor Node.

🏭

Industrial Automation Bus Interface

The ADM3491ARZ fits industrial automation equipment that connects a 3.3 V controller to a balanced RS-485 or RS-422 field link. Its 10 Mbps maximum data rate supports high-speed command and telemetry traffic, while the 19 kΩ receiver input impedance permits up to 50 transceivers on a bus. The full-duplex arrangement provides separate transmit and receive paths, avoiding half-duplex turnaround delays. Its 840 µA operating current also suits compact controller boards. Deployment should include verified termination, common-mode protection, and an isolated or non-isolated grounding strategy matched to the installation.

📊

Factory Data Acquisition

The ADM3491ARZ is appropriate for factory data-acquisition modules that must exchange measurements over a long balanced cable while operating from a 3.3 V system rail. Its 10 Mbps capability allows the interface to carry time-stamped sensor data and control updates without the low-speed constraints of common RS-485 transceivers. Short-circuit protection and thermal shutdown improve robustness against accidental bus faults. For installation, use twisted-pair routing, controlled terminations, surge protection, and a ground reference compatible with the transceiver’s full common-mode operating range.

🏠

Building Control Network

The ADM3491ARZ can connect building-control controllers, sensors, and gateways over RS-485 or RS-422. Its low 840 µA supply consumption benefits compact wall-mounted controllers, and the 2 nA shutdown current helps maintain low standby demand. The 10 Mbps rate is more than sufficient for typical HVAC, access, lighting, and environmental-control traffic while also accommodating higher-speed local diagnostics. Maintain a consistent reference ground and separate surge currents from the differential pair to prevent transient energy from perturbing the receiver.

🔧

Instrumentation Communication

The ADM3491ARZ is useful in laboratory and industrial instruments that expose a balanced communications port to a host controller. Its 3.3 V operation suits modern mixed-signal systems, and interoperability with 5 V logic helps connect the interface to established digital circuitry. The full-duplex topology allows command transmission and response reception to occur simultaneously, shortening instrument-control cycles. Designers should use the manufacturer pin definitions for the exact package and should validate cable length, baud rate, termination, and common-mode limits as a complete channel.

🌐

Point-to-Point Data Link

The ADM3491ARZ supports point-to-point balanced links where full-duplex operation is valuable, including equipment-to-controller and board-to-board communications. Separate differential transmit and receive channels eliminate the need to share a bus pair, while the 10 Mbps rate supports rapid file transfer, configuration updates, and real-time control traffic. The 3.3 V supply and 840 µA operating current simplify integration with embedded systems. For long cable runs or electrically noisy environments, add appropriate transient protection and verify that the complete channel remains inside the supported common-mode range.

🧩

Power-Sensitive Sensor Node

The ADM3491ARZ fits low-power sensor nodes that communicate over a wired differential bus when wireless communication is unsuitable. Its 840 µA operating consumption and 2 nA shutdown current reduce demand when the node spends substantial time idle. The 19 kΩ receiver input impedance allows multiple nodes to share a bus, and the 10 Mbps rate supports aggregated telemetry. Keep the transceiver supply rail clean, bypass it close to the device, and use a shutdown strategy that avoids disrupting required bus-fail-safe behavior during low-power transitions.

What is the operating voltage of ADM3491ARZ?
The ADM3491ARZ operates from a single +3.3 V supply. According to the Analog Devices ADM3491 datasheet, its low-power architecture uses 840 µA of supply current and can reduce consumption to 2 nA in shutdown mode. This operating range suits modern 3.3 V controllers, industrial automation equipment, and systems that benefit from low standby consumption. The device is also interoperable with 5 V logic, allowing its digital interfaces to operate alongside compatible controllers and other interface components.
What is the maximum data rate of ADM3491ARZ?
The ADM3491ARZ supports a maximum data rate of 10 Mbps. The Analog Devices manufacturer datasheet identifies the ADM3491 family as a 3.3 V, slew-rate-limited, half- and full-duplex RS-485 and RS-422 transceiver family, with the ADM3491 specified for 10 Mbps operation. This rate is suitable for factory automation, industrial data acquisition, instrumentation, and other short balanced links where higher throughput is needed without abandoning RS-485 or RS-422 signaling.
What is ADM3491ARZ used for?
The ADM3491ARZ is used to connect 3.3 V digital logic to balanced RS-422 or RS-485 communication lines. According to the Analog Devices product page, it is a low-power differential line transceiver suitable for multipoint transmission lines, industrial control, data acquisition, and building or factory communications. Its 10 Mbps data rate supports faster links, while its shutdown function helps conserve power when the interface is not active.
Where can I download the ADM3491ARZ datasheet PDF?
The ADM3491ARZ datasheet PDF is available directly from Analog Devices through the official manufacturer link listed on this page. It describes the device features, electrical characteristics, pin descriptions, applications, and RS-422/RS-485 behavior. The separate ADM3491-1 datasheet is linked as the official technical document because it covers the closely related ADM3491 family. Use its pin-description table to verify all board-net assignments before fabrication.
Where can I find the ADM3491ARZ pinout?
The ADM3491ARZ pinout is found in the pin-description section of the official Analog Devices ADM3491 family datasheet. The exact package drawing and pin table should be used for the 14-lead SOIC configuration. This page does not reproduce a potentially ambiguous terminal map because package-specific details must be matched to the ordered device before PCB routing. Verify driver outputs, receiver inputs, enable controls, grounds, and supply pins against the datasheet table.
Is ADM3491ARZ half-duplex or full-duplex?
The ADM3491ARZ is a full-duplex RS-485/RS-422 transceiver. The DigiKey product listing identifies the exact ADM3491ARZ device as a one-transceiver, full-duplex RS-422/RS-485 interface in a 14-lead SOIC package. Full duplex uses separate differential transmit and receive paths, allowing simultaneous communication. This differs from an eight-lead half-duplex RS-485 arrangement in which the driver and receiver share the same bus pair.
What can replace ADM3491ARZ?
The closest documented same-brand replacement choices are the ADM3491AR-1 and ADM3491ARZ-1 variants, but pin and electrical compatibility must be confirmed against the relevant datasheet and ordering code before substitution. The ADM3491-1 product family provides the principal alternative source for a 3.3 V RS-422/RS-485 transceiver, while the ADM3491ARZ-REEL7 ordering code changes reel packaging rather than the underlying function. Confirm the exact package, temperature grade, enable configuration, and transceiver mode in the manufacturer documentation.
Is ADM3491ARZ the same as ADM3491AR-1?
The ADM3491ARZ and ADM3491AR-1 are closely related ADM3491-family devices, but the “-1” ordering designation requires explicit comparison of temperature grade and package options. Both relate to the low-power 3.3 V RS-422/RS-485 transceiver family, which supports full-duplex operation in the 14-lead SOIC configuration. Use the Analog Devices ordering guide and datasheet limits to confirm whether the -1 variant changes the qualified temperature range or only reflects an orderable grade.
What is the best Analog Devices equivalent for ADM3491ARZ?
The best Analog Devices-family equivalent to evaluate is the ADM3491AR-1, subject to confirmation of its exact package and temperature grade. It belongs to the same 3.3 V differential transceiver family described by Analog Devices for RS-422 and RS-485 operation. The critical checks are the 14-lead SOIC footprint, 10 Mbps-capable operating mode, full-duplex configuration, enable behavior, and operating-temperature limits. Do not substitute solely from the family name without reviewing the detailed ordering information.
When should I choose ADM3491ARZ over ADM3491AR-1?
Choose ADM3491ARZ when its documented temperature grade and orderable configuration meet the product’s environmental and sourcing requirements and a full-duplex 3.3 V RS-422/RS-485 interface is required. Consider ADM3491AR-1 when its specified temperature range, package form, and orderable status better match the design. Both options belong to the same Analog Devices transceiver family, so the decision should be based on the ordering table rather than assumed from the suffix.
Is ADM3491ARZ suitable for industrial automation?
Yes, ADM3491ARZ is suitable for industrial automation interfaces that require a low-power, 3.3 V differential transceiver. Its 10 Mbps maximum rate, 840 µA operating supply current, 19 kΩ receiver input impedance, short-circuit protection, and support for up to 50 transceivers on a bus fit balanced industrial links. For harsh installations, also verify the device’s -40 °C to +85 °C operating range, transient protection network, grounding strategy, and isolation requirements.
How many transceivers can be on an ADM3491 bus?
The ADM3491 family supports up to 50 transceivers on a bus. The Analog Devices manufacturer datasheet lists a 19 kΩ input impedance and bus capacity of up to 50 transceivers, while also specifying EIA RS-422 and RS-485 compliance over the full common-mode range. Actual deployment still requires correct termination, stub control, biasing where needed, and protection suitable for the installation environment; bus population alone does not guarantee reliable operation.
Does ADM3491ARZ support 5 V logic?
Yes, the ADM3491ARZ is interoperable with 5 V logic. The Analog Devices manufacturer datasheet identifies 5 V logic interoperability as a family feature even though the transceiver itself operates from a single 3.3 V supply. This is useful in mixed-generation equipment where the bus-side interface must connect to a 5 V-compatible digital device. Signal-level and timing compatibility should still be checked at the system level rather than inferred solely from supply voltage.
What are the key specifications of ADM3491ARZ that engineers should know?
The ADM3491ARZ is a 3.3 V, full-duplex RS-422/RS-485 transceiver rated for 10 Mbps operation in a 14-lead SOIC package. According to the Analog Devices manufacturer datasheet, important characteristics include 840 µA supply current, 2 nA shutdown current, 19 kΩ receiver input impedance, up to 50 transceivers per bus, 8 ns transmit skew, short-circuit protection, thermal shutdown, 5 V logic interoperability, and operation from -40 °C to +85 °C.
Where can I buy ADM3491ARZ and check its lead time?
Use the Request a Quote form on this page to ask for ADM3491ARZ availability, current unit pricing, minimum order quantity, and production lead time. The form is the appropriate route for a quote-based purchase without inserting rapidly changing commercial figures into the technical content. For engineering approval, request the exact ADM3491ARZ ordering code, delivery packaging, traceability information, and a lot-consistent date code before releasing the component to production.

کے لیے انجینئرنگ ریفرنس ڈیٹا ADM3491ARZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose ADM3491ARZ when the design requires a 3.3 V, full-duplex RS-422 or RS-485 interface operating at up to 10 Mbps in a 14-lead SOIC package. Its 840 µA operating current, 2 nA shutdown current, 19 kΩ receiver input impedance, and support for 50 transceivers per bus make it well suited to industrial automation, data acquisition, instrumentation, and building-control links. Evaluate ADM3491AR-1 or ADM3491ARZ-1 when their documented temperature grade and ordering status better fit the product plan; they belong to the same Analog Devices family and retain closely comparable transceiver functions. ADM3491ARZ-REEL7 is primarily a distinct reel-ordering configuration, so confirm manufacturing logistics rather than selecting it as an electrical upgrade. Do not choose an eight-lead half-duplex transceiver when the board depends on separate transmit and receive paths. Final approval should verify the exact pinout, temperature limits, transceiver mode, cable termination, protection network, and common-mode environment.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ ADM3491AR-1 ADM3491ARZ-1 ADM3491-1 ADM3491ARZ-REEL7
Package 14-lead SOIC 14-lead SOIC 14-lead SOIC 14-lead SOIC 14-lead SOIC
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Product Type Full-duplex differential transceiver Differential transceiver Differential transceiver Differential transceiver Full-duplex differential transceiver
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Supported Standards EIA RS-422 and EIA RS-485 EIA RS-422 and EIA RS-485 EIA RS-422 and EIA RS-485 EIA RS-422 and EIA RS-485 EIA RS-422 and EIA RS-485
Maximum Data Rate 10 Mbps 10 Mbps 10 Mbps 10 Mbps 10 Mbps
Receiver Input Impedance 19 kΩ 19 kΩ 19 kΩ 19 kΩ 19 kΩ
Supply Current 840 µA 840 µA 840 µA 840 µA 840 µA
Shutdown Current 2 nA 2 nA 2 nA 2 nA 2 nA

اہم امتیازی خصوصیات

  • Full-duplex operation in a 14-lead package (بمقابلہADM3483EARZ-REEL7)
  • Higher supported signaling rate within the ADM3491 family (بمقابلہADM3483EARZ-REEL7)
  • Low-power operation with shutdown support (بمقابلہADM3491AR-1)

ڈیزائن نوٹس

Route the differential pair as a tightly coupled pair over a continuous reference plane, keeping both conductors over the same plane and avoiding splits, vias, and test pads that create impedance discontinuities. Connect the receiver and transmitter grounds consistently with the cable shield or chassis strategy used by the installation. High-current switching nodes and transient-protection return paths should remain outside the signal area so their current does not cross the differential traces.

Place the device bypass capacitor immediately adjacent to its supply and ground pins, with a short, low-impedance connection to the quiet ground plane. Keep the 3.3 V supply free of switching-converter ripple because receiver and transmit performance depend on a stable reference even though the specified supply current is only 840 µA. If the transceiver shares a board with switching circuitry, verify supply ripple and ground bounce at the device rather than relying only on the average current requirement.

Do not treat an 8-lead half-duplex transceiver as an automatic replacement for the ADM3491ARZ. The exact ADM3491ARZ is identified as a 14-lead, full-duplex device, and the physical signal paths differ from half-duplex implementations that share one bus pair. Also distinguish the -1 grade suffix from reel-orientation suffixes in the ordering code, and verify the operating-temperature range before approving a substitution.

Use twisted-pair cabling and proper bus termination to control reflections and radiated emissions. Where the installation exposes the bus to industrial surges, add a protection network selected for the required common-mode voltage and transient severity. The manufacturer datasheet identifies IEC 1000-4-4 compatibility above 1 kV for the family, but this does not remove the need to analyze the complete system and provide an appropriate energy-dissipation path.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The family datasheet identifies IEC 1000-4-4 compatibility above 1 kV. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status require confirmation for the exact ordering code.

متعلقہ تلاشیں

adm3491arz datasheet adm3491arz reel ADM3491ARZ datasheet pdf ADM3491ARZ pinout ADM3491ARZ equivalent ADM3491ARZ replacement ADM3491ARZ cross reference ADM3491ARZ vs ADM3491AR-1 ADM3491ARZ footprint ADM3491ARZ application circuit ADM3491ARZ 10 Mbps Analog Devices ADM3491ARZ ADM3491ARZ price ADM3491ARZ stock

متعلقہ اجزاء اور اصطلاحات

Analog Devices ADM3491ARZ ADM3491AR-1 ADM3491ARZ-1 ADM3491-1 ADM3491ARZ-REEL7 ADM3483EARZ-REEL7 RS-485 RS-422 differential line transceiver interface IC full-duplex transceiver multipoint bus 3.3 V power supply 10 Mbps 840 µA 2 nA 19 kΩ 50 transceivers 8 ns skew 14-lead SOIC surface mount IEC 1000-4-4 industrial automation data acquisition
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں