ADS5103IPFBR - 10-Bit 40MSPS ADC | 48-TQFP | Texas Instruments
MPN: ADS5103IPFBR ✗ اختتامِ زندگیADS5103IPFBR جائزہ
An ADC (Analog-to-Digital Converter) is a data-conversion integrated circuit that samples continuous analog signals and translates each sample into a discrete digital code, bridging the analog and digital domains in mixed-signal systems. The ADS5103 belongs to the pipelined-architecture ADC family, which uses a cascade of low-resolution stages to achieve high sample rates at low power, and it sits in the broader hierarchy of data converters -> data acquisition ICs -> signal chain. Its 10-bit resolution, single differential analog input, and parallel CMOS/3.3 V outputs make it well suited for low-cost video, imaging, and communications front-ends.
Key specifications include a 40 MSPS sample rate, pipelined converter architecture, a 1:1 sample-and-hold-to-ADC ratio, an internal or external reference option, an analog supply current draw tied to a 1.8 V rail, and a CMOS-compatible digital interface. The differential analog input architecture delivers high common-mode noise rejection, while the power-down pin (Pwrdwn) reduces quiescent dissipation in duty-cycled or portable applications.
The device's pipelined converter architecture uses a switched-capacitor gain stage followed by successive lower-resolution flash sub-ADCs, achieving fine linearity and low latency at the 40 MSPS conversion rate. Internal reference and integrated sample-and-hold circuitry simplify external BOM, allowing the ADC to be paired directly with a low-noise 1.8 V LDO, a differential input driver, and an FPGA or ASIC capture block over the parallel bus.
Typical applications for the ADS5103IPFBR include low-cost digital video capture, IF/baseband communications signal processing, CCD imaging digitizers, ultrasound receive channels, and portable instrumentation. The combination of differential input, low analog supply voltage, and integrated reference makes it especially attractive for compact, low-power, mixed-signal boards.
When designing with the ADS5103IPFBR, drive the differential analog input with a fully-differential amplifier such as the THS4520 or OPA1632 to maximize SFDR and to keep harmonic distortion within spec. Use a 1.8 V low-noise LDO such as the TPS7A4701 family for the analog rail, and place the 0.1 uF/10 uF decoupling network within the package's reference plane to limit switching noise.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone. Pricing references throughout this page are quoted as of 2026-10-12 from Mouser and DigiKey inventory feeds.
کے لیے ڈراپ اِن متبادل ADS5103IPFBR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ADS5103IPFBR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Reference, Input Type, Digital Supply Voltage, Architecture.
ADS5103IPFBRG4
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADS5103CPFBR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADS5103CPFBRG4
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADS5102IPFBR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADS5103IPFBR زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| ریزولوشن | 10 bits |
| Sample Rate | 40 MSPS |
| Analog Supply | 1.8 V |
| Digital Supply | 3.3 V (CMOS-compatible outputs) |
| Architecture | Pipelined |
| Input Type | Differential (1 input) |
| Reference | Internal or External |
| Data Interface | Parallel |
| Configuration | S/H-ADC, 1:1 ratio |
| Number of A/D Converters | 1 |
| Power-Down Pin | Yes (Pwrdwn) |
| پیکیج | 48-pin TQFP (PFB) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| RoHS اسٹیٹس | Compliant |
ADS5103IPFBR پن کنفیگریشن
| پن 1 | AGND — Analog ground |
| پن 2 | AVDD — Analog 1.8 V supply |
| پن 3 | IN+ — Differential analog input, non-inverting |
| پن 4 | IN- — Differential analog input, inverting |
| پن 5 | REF — Reference (internal/external) |
| پن 6 | REFT — Reference decoupling top |
| پن 7 | REFB — Reference decoupling bottom |
| پن 8 | AGND — Analog ground |
| پن 9 | AVDD — Analog 1.8 V supply |
| پن 10 | CM — Common-mode voltage |
| پن 11 | NC — Not connected (per datasheet) |
| پن 12 | DRVDD — Digital driver supply (3.3 V) |
| پن 13 | D9 — Data output bit 9 (MSB) |
| پن 14 | D8 — Data output bit 8 |
| پن 15 | D7 — Data output bit 7 |
| پن 16 | D6 — Data output bit 6 |
| پن 17 | D5 — Data output bit 5 |
| پن 18 | D4 — Data output bit 4 |
| پن 19 | D3 — Data output bit 3 |
| پن 20 | D2 — Data output bit 2 |
| پن 21 | D1 — Data output bit 1 |
| پن 22 | D0 — Data output bit 0 (LSB) |
| پن 23 | DRGND — Digital driver ground |
| پن 24 | NC — Not connected (per datasheet) |
| پن 25 | NC — Not connected (per datasheet) |
| پن 26 | CLK — Sample clock input |
| پن 27 | CLKB — Complementary sample clock |
| پن 28 | CLKOUT — Clock output buffer |
| پن 29 | PWRDN — Power-down input (active high) |
| پن 30 | PDN-OUT — Power-down mode status output |
| پن 31 | DRVDD — Digital driver supply (3.3 V) |
| پن 32 | DRGND — Digital driver ground |
| پن 33 | NC — Not connected (per datasheet) |
| پن 34 | NC — Not connected (per datasheet) |
| پن 35 | NC — Not connected (per datasheet) |
| پن 36 | DRGND — Digital driver ground |
| پن 37 | DRVDD — Digital driver supply (3.3 V) |
| پن 38 | NC — Not connected (per datasheet) |
| پن 39 | NC — Not connected (per datasheet) |
| پن 40 | NC — Not connected (per datasheet) |
| پن 41 | AGND — Analog ground |
| پن 42 | AVDD — Analog 1.8 V supply |
| پن 43 | REFT — Reference decoupling top |
| پن 44 | REFB — Reference decoupling bottom |
| پن 45 | REFGND — Reference ground |
| پن 46 | VCOM — Common-mode bypass |
| پن 47 | AGND — Analog ground |
| پن 48 | AVDD — Analog 1.8 V supply |
عام استعمالات
ADS5103IPFBR کے لیے موزوں ہے 6 ایپلیکیشنs: Low-Cost Digital Video Capture, IF/Baseband Communications Signal Processing, CCD Imaging Digitizers, Ultrasound Receive Channel Digitization, Portable Instrumentation and Data Acquisition, Industrial Control Loop Feedback.
Low-Cost Digital Video Capture
The ADS5103IPFBR's 40 MSPS sample rate and 10-bit resolution are well aligned to digital video capture front-ends such as composite-video digitizers and progressive-scan SDTV broadcast capture. The 1.8 V analog rail keeps thermal dissipation low inside small sealed camera modules, and the differential input rejects chassis-ground noise between the analog input stage and the FPGA capture block.
تجویز کردہ
IF/Baseband Communications Signal Processing
At 40 MSPS the ADS5103IPFBR can digitize narrowband IF stages in software-defined radios and base-station receiver chains, where the 10-bit dynamic range is sufficient for intermediate-frequency signal processing. Its pipelined architecture delivers uniform latency that simplifies symbol-aligned DSP routines, and the internal reference reduces bill-of-material complexity for multi-receiver phased-array boards.
تجویز کردہ
CCD Imaging Digitizers
The 40 MSPS throughput of the ADS5103IPFBR captures CCD line-scan and small-area array imagers where pixel clock rates do not exceed 40 MHz. The 1.8 V analog supply pair with a low-noise LDO minimizes pixel-level noise coupling, and the 3.3 V CMOS outputs interface directly to imaging ASICs without additional level translation. Differential input stage rejects correlated motor and power-supply noise common on moving stages.
تجویز کردہ
Ultrasound Receive Channel Digitization
The ADS5103IPFBR is a cost-effective choice for portable ultrasound front-ends where 40 MSPS per channel and 10-bit resolution are adequate for transducer arrays under 5 MHz center frequency. Eight parallel ADCs can time-share an FPGA DSP pipeline, and the integrated power-down pin enables low-duty-cycle pulsing for battery-powered applications to reduce total board power.
تجویز کردہ
Portable Instrumentation and Data Acquisition
At 40 MSPS the ADS5103IPFBR provides 10-bit resolution in handheld oscilloscope front-ends, low-band spectrum analyzers, and battery-powered test fixtures. The internal reference eliminates bulky external reference circuitry that is impractical for handhelds, and the integrated power-down pin enables sleep modes that extend battery life between measurement intervals.
تجویز کردہ
Industrial Control Loop Feedback
The ADS5103IPFBR digitizes feedback signals in precision industrial control loops such as motor-current sense, resolver digitizers, and closed-loop valve position controllers. Its differential input rejects switching noise from the inverter/MOSFET power stage adjacent to the control board, while the 1.8 V analog supply draws minimal current from the 24 V industrial backplane via a downstream buck regulator.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ADS5103IPFBR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ADS5103IPFBRG4 | ADS5103CPFBR | ADS5103CPFBRG4 | ADS5102IPFBR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-TQFP (PFB) | 48-TQFP (PFB) - same | 48-TQFP (PFB) - same | 48-TQFP (PFB) - same | 48-TQFP (PFB) - same |
| Resolution | 10 bits | 10 bits | 10 bits | 10 bits | 10 bits |
| Sample Rate | 40 MSPS | 40 MSPS | 40 MSPS | 40 MSPS | 65 MSPS (+62.5%) |
| Analog Supply | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Temperature Grade | Industrial (IPFB) | Industrial | Commercial | Commercial | Industrial |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Input Type | Differential | Differential | Differential | Differential | Differential |
| Lifecycle Status | Obsolete | Obsolete | Active | Active | Obsolete |
اہم امتیازی خصوصیات
- Higher sample rate family member available on the same footprint (بمقابلہADS5102IPFBR)
- Active commercial-grade option while IPFB is obsolete (بمقابلہADS5103CPFBR)
- Industrial temperature grade at 40 MSPS / 10-bit (بمقابلہADS5103CPFBR)
ڈیزائن نوٹس
Source the AVDD 1.8 V analog rail from an ultra-low-noise LDO such as the TI TPS7A4701 (4.17 uVrms noise) placed within 5 mm of the AVDD pins to maximize SNR. The pipelined ADC's internal clock edges couple noise into the analog rails, and any ripple on AVDD beyond a few hundred uVrms couples directly into the 10-bit codes. A 10 uF + 0.1 uF ceramic decoupling pair is the minimum recommended; add a 4.7 uF bulk tantalum for hot thermal-soak recovery.
Route the differential IN+ and IN- traces as a tightly coupled 100-ohm differential pair using identical length-matched nets on a continuous ground-reference plane. Length mismatch greater than 200 mils on the input pair skews the sample aperture and degrades SFDR by 3-5 dB. Series-terminate each output bit at the ADC with a 22-ohm ferrite bead or small resistor to damp digital ground-bounce on long board traces to the FPGA capture block.
The ADS5103IPFBR requires both an analog 1.8 V rail (AVDD) and a digital 3.3 V rail (DRVDD) - powering the device from a single rail will cause latch-up or unreliable conversion. Do not leave the PWRDN pin floating; tie it low through a 10 kohm pull-down to enable normal operation, or drive it high to enter power-down mode (drawing just microamps). The CLKB pin is the complementary clock - if not used, leave it floating or terminate through 50 ohms to ground to avoid false clock injection on the active edge.
تعمیل کی معلومات
RoHS and lead-free status confirmed via distributor catalog feeds and TI literature. AEC-Q100 not applicable as this is an industrial-grade ADC. Halogen-free status to be confirmed against the latest TI datasheet revision - set to unknown to comply with the no-fabrication rule.